EN 14450-2017 en Secure storage units - Requirements classification and methods of test for resistance to burglary - Secure safe cabinets.pdf

《EN 14450-2017 en Secure storage units - Requirements classification and methods of test for resistance to burglary - Secure safe cabinets.pdf》由会员分享，可在线阅读，更多相关《EN 14450-2017 en Secure storage units - Requirements classification and methods of test for resistance to burglary - Secure safe cabinets.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、Secure storage units Requirements, classification and methods of test for resistance to burglary Secure safe cabinetsBS EN 14450:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14450 November 2017 ICS 13.310 Su

2、persedes EN 14450:2005English Version Secure storage units - Requirements, classification and methods of test for resistance to burglary - Secure safe cabinets Units de stockage en lieu sr - Exigences, classification et mthodes dessai de rsistance leffraction - Coffres domestiques Wertbehltnisse - A

3、nforderungen, Klassifizierung und Methoden zur Prfung des Widerstandes gegen Einbruchdiebstahl - Sicherheitsschrnke This European Standard was approved by CEN on 16 July 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Eur

4、opean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versio

5、ns (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, B

6、elgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Swe

7、den, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for C

8、EN national Members. Ref. No. EN 14450:2017 ENational forewordThis British Standard is the UK implementation of EN 14450:2017. It supersedes BS EN 14450:2005, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee GW/2, Secure storage of cash, valuables and d

9、ata media.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by

10、BSI Standards Limited 2017ISBN 978 0 580 88457 3ICS 13.310Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2017.Amendments/corrigenda issued since pub

11、licationDate Text affectedBRITISH STANDARDBS EN 14450:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14450 November 2017 ICS 13.310 Supersedes EN 14450:2005English Version Secure storage units - Requirements, classification and methods of test for resistance to burglary - Secure safe cabin

12、ets Units de stockage en lieu sr - Exigences, classification et mthodes dessai de rsistance leffraction - Coffres domestiques Wertbehltnisse - Anforderungen, Klassifizierung und Methoden zur Prfung des Widerstandes gegen Einbruchdiebstahl - Sicherheitsschrnke This European Standard was approved by C

13、EN on 16 July 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards

14、may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notifie

15、d to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Icela

16、nd, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELE

17、C Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14450:2017 EBS EN 14450:2017EN 14450:2017 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative re

18、ferences 5 3 Terms and definitions . 5 4 Classification and requirements 6 4.1 Classification . 6 4.2 Requirements . 6 5 Technical Documentation 7 6 Test specimen . 8 7 Tool attack test . 8 7.1 Tool attacks . 8 7.1.1 Tool list . 8 7.1.2 Tool attack procedure . 9 7.1.3 Timing 10 7.1.4 Test criteria 1

19、1 7.2 Testing programme . 11 7.2.1 Free-standing cabinets . 11 7.2.2 Wall or floor cabinets . 11 7.2.3 Calculation of tool attack resistance . 12 7.2.4 Completion of tool attack test 12 8 Anchoring strength test . 12 9 Test report 13 10 Marking 13 Annex A (normative) . 14 Bibliography . 17 BS EN 144

20、50:2017EN 14450:2017 (E) 3 European foreword This document (EN 14450:2017) has been prepared by Technical Committee CEN/TC 263 “Secure safe cabinets”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identic

21、al text or by endorsement, at the latest by May 2018, and conflicting national standards shall be withdrawn at the latest by May 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifyi

22、ng any or all such patent rights. This document supersedes EN 14450:2005. In comparison with EN 14450:2005, the following changes have been made: updating introduction; changing testing requirements regarding marking time (Clause 7.1.3.2) and anchoring (Clause 7.1.2.1); size of the tool “wedge” chan

23、ged in Clause 7.1.1; a note was changed to a requirement and the test equipment shall now have a capacity of at least 30 kN (Clause 8); editorial clarification of the positioning of anchoring holes (Clause 4.2.2); editorial changes amongst others in Clauses 4.1, 7.1.2.4, 7.1.3, 7.1.4.6, 7.2, Table 1

24、, Table 2 and Annex A). According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic o

25、f Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 14450:2017EN 14450:2017 (E) 4 Introduction Tests

26、are made and the results used to classify resistance to burglary. The standard covers products meant for purposes where the security resistance required is less than that measured by EN 1143-1. Normally these products are used in lower risk situations. Secure safe cabinets aim to protect against bur

27、glars who typically have no specific information on the level of resistance offered by construction and are not prepared to take high risks. The burglar attempts to gain access to the cabinet using simple tools which they normally bring to access premises. To reflect this limitation the tools permit

28、ted in the type tests of this standard are mostly manual tools (“hand tools”). However for purpose of repeatability two mains driven tools are included: electric drill (to eliminate power loss to battery state); electric disc grinder (represents and replaces hammer and chisel testing to eliminate te

29、sters fatigue and risk of injury especially in respect of the test conditions by counting the gross time). Depending on the criminal, the conditions at the place of crime and the availability of tools, considerably longer times are likely to occur in real burglar attacks than in a type test. It shou

30、ld be noted that results of manual testing are dependent of the skills of the testing team. It is therefore recommended that testing teams exchange skills and experience on a regular basis. There is no requirement under this standard to test for resistance to fraudulent access. BS EN 14450:2017EN 14

31、450:2017 (E) 5 1 Scope This document establishes the basis for testing and classifying secure safe cabinets. The standard covers products meant for purposes where the security resistance required is less than that measured by EN 1143-1. Normally these products are used in lower risk situations. 2 No

32、rmative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendment

33、s) applies. EN 1300, Secure storage units - Classification for high security locks according to their resistance to unauthorized opening 3 Terms and definitions For the purpose of this document, the following terms and definitions apply. 3.1 secure safe cabinet storage unit which protects its conten

34、t against burglary, which has at least one internal side 1 m length when closed, and the interior of which is accessed through a lockable door or lid 3.2 free-standing cabinet secure safe cabinet whose protection against burglary depends only upon the materials and construction of its primary manufa

35、cture and not upon materials added or attached during installation 3.3 wall cabinet secure safe cabinet for installation into a wall and whose protection against burglary is partly dependent upon the wall(s) and the materials added during installation 3.4 floor cabinet secure safe cabinet for instal

36、lation into a floor and whose protection against burglary is partly dependent upon materials added during installation 3.5 working time time spent during testing during which one or more tools are used to create a change in the test specimen 3.6 gross time time from when a test is started to when th

37、e test is complete or abandoned 3.7 encasement material added at installation to protect and anchor wall cabinets and floor cabinets BS EN 14450:2017EN 14450:2017 (E) 6 3.8 tool points, TP numerical value assigned to test tool 3.9 security units, SU numerical value expressing resistance against burg

38、lary attack 4 Classification and requirements 4.1 Classification Secure safe cabinets are classified to a resistance level according to Table 1. Table 1 Requirements for classification of secure safe cabinets S1 S2 Minimum resistance for access 2,00 SU 5,00 SU Limit to number and type of tools used

39、for testing 40 TP 60 TP Minimum strength per anchoring hole 20 kN 30 kN Minimum locking One lock to EN 1300 One lock to EN 1300 Gross attack time is limited as described in 7.2.4 b). 4.2 Requirements 4.2.1 There shall be no holes through the protection material other than those for locks, cables or

40、anchoring. One cable hole is allowed, this shall not exceed 100 mm2. 4.2.2 A free-standing cabinet with a mass less than 1 000 kg shall have at least two holes by which it can be anchored. These holes shall be at one face or at two different faces through which it is to be anchored. The anchoring as

41、sembly for each anchoring hole shall sustain the minimum anchoring strength given in Table 1. 4.2.3 Secure safe cabinets shall be provided with operating and installation instructions, including instructions in respect of the locks and anchoring. For freestanding secure safe cabinets the installatio

42、n instruction shall note that the cabinet shall be anchored on site through at least two of the anchoring holes (see 4.2.2). BS EN 14450:2017EN 14450:2017 (E) 7 5 Technical Documentation The technical documentation shall contain the following information: 5.1 Date of issue and the name of the manufa

43、cturer (or the name and status of the applicant requesting testing) shall be on each page. 5.2 Statement of the type and model number of secure safe cabinet, e.g. free-standing cabinet, wall cabinet or floor cabinet. 5.3 Drawings of the test specimen and documents giving the following: a) weight, ou

44、tside and inside dimensions, and the manufacturing tolerances of the dimensions; b) horizontal and vertical cross-sections; c) the quantity, layout and features of locks, boltwork and relocking devices; d) the quantity, pitch and position of door bolts, their dimensions (e.g. cross-section), throw a

45、nd engagement and their type (e.g. moving or fixed); e) the location and design of any local areas of special protection material; f) purpose, position and dimensions of any holes which pass through the protection material with details of any associated special protection; g) details of optional fea

46、tures, e.g. time locking and time delay locking; h) specification of the materials of construction. 5.4 Operating and installation instructions, including instructions in respect of the locks and anchoring. 5.5 In addition to 5.2, 5.3 and 5.4, for wall cabinets and floor cabinets the following infor

47、mation shall be provided: a) details of the recommended procedure for installation; b) drawing showing the recommended plane of door or lid in relation to the surface of the wall or floor into the cabinet is to be installed; c) details of encasement materials (see 3.7); d) recommendation for the pro

48、portion of the body to be encased and the thickness of the encasement; e) identification of any areas of the body which are not protected by material added at installation; 5.6 List of all locks that may be fitted, giving the manufacturer and model number; 5.7 Details of any materials or device(s) i

49、ntended to generate gas, smoke, soot, etc., in the event of physical attack or which could generate harmful substances during testing. BS EN 14450:2017EN 14450:2017 (E) 8 6 Test specimen 6.1 The test specimen shall be a complete secure safe cabinet. Optional features which could decrease resistance time shall be present in the test specimen. Optional features which could increase resistance time shall either not be present or shall be made inoperative. 6.2 Wall cabinets and floor cabinets shall be encased according to the recomm