DLA MS14057 REV H-2009 INSERT ARRANGEMENTS ELECTRICAL CONNECTOR SIZE 52 CLASS L 200 AMPS [Refer To DLA MIL-DTL-22992 G SUPP 1 DLA MIL-DTL-22992 G DLA MIL-C-22992B SUPP 1A DLA MIL-C.pdf

《DLA MS14057 REV H-2009 INSERT ARRANGEMENTS ELECTRICAL CONNECTOR SIZE 52 CLASS L 200 AMPS [Refer To DLA MIL-DTL-22992 G SUPP 1 DLA MIL-DTL-22992 G DLA MIL-C-22992B SUPP 1A DLA MIL-C.pdf》由会员分享，可在线阅读，更多相关《DLA MS14057 REV H-2009 INSERT ARRANGEMENTS ELECTRICAL CONNECTOR SIZE 52 CLASS L 200 AMPS [Refer To DLA MIL-DTL-22992 G SUPP 1 DLA MIL-DTL-22992 G DLA MIL-C-22992B SUPP 1A DLA MIL-C.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 MS14057H 1 April 2009 SUPERSEDING MS14057G 26 October 2005 INCH-POUND DETAIL SPECIFICATION SHEET INSERT ARRANGEMENTS, ELECTRICAL CONNECTOR, SIZE 52, CLASS L, 200 AMPS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring

2、the product described herein shall consist of this specification sheet and MIL-DTL-22992. Quantity Contact Size Socket SAE-AS39029/49- Pin SAE-AS39029/48- 1 A 4/0 335 327 1 N 4/0N 335 (see note 5) 328 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. Unless other

3、wise specified, tolerance is .002 (.05 mm). 2. Unless otherwise specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -02-ICEA 2-NO 2/0 conductor round type W cable, 0 - 600 volts. 4. Trademark and 52-( ) shall appear in available space. Contact identifying letter

4、shall be located so as to identify relative contact. 5. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is the same as the power contact. FIGURE 1. 28 volt DC two wire, -02 insert arrangement, service D. AMSC N/A FSC 5935 Provided by IHSNot for Resal

5、eNo reproduction or networking permitted without license from IHS-,-,-MS14057H 2Quantity Contact Size Socket SAE-AS39029/49-Pin SAE-AS39029/48-2 A, B 4/0 335 327 1 N 4/0N 335 (see note 5) 328 3 G1, G2, G3 4G 332 322 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information onl

6、y. Unless otherwise specified, tolerance is .002 (.05 mm). 2. Unless otherwise specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -02-IPCEA 3-NO 2/0 conductor round type W cable, 0 - 600 volts. 4. Trademark and 52-( ) shall appear in available space. Contact ide

7、ntifying letter shall be located so as to identify relative contact. 5. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is the same as the power contact. FIGURE 2. AC single phase three wire grounding, -06 insert arrangement, service D. Provided by I

8、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14057H 3Quantity Contact Size Socket SAE-AS39029/49- Pin SAE-AS39029/48- 3 A, B, C 4/0 335 327 1 N 4/0N 335 (see note 6) 328 4 G1, G2, G3, G4 4G 332 322 NOTES: 1. Dimensions are in inches. Metric equivalents are g

9、iven for information only. Unless otherwise specified, tolerance is .002 (.05 mm). 2. Unless otherwise specified, front face of pin insert pattern is shown. Socket inserts are the reverse. 3. -12-Cable ICEA 4-NO 4/0 conductor round type G cable, 0 - 600 volts. 4. -13-Cable-C0-04-HDE (4/0000) 2380 in

10、 accordance with MIL-DTL-3432. 5. Mark 52-12 on 52-13 insert. Trademark and 52-( ) shall appear in available space. Contact identifying letter shall be located so as to identify relative contact. 6. Only the pin contact is lengthened and has the N (neutral) designation. The mating socket contact is

11、the same as the power contact. FIGURE 3. AC three phase four wire grounding, -12 and -13 insert arrangements, service D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14057H 4Insert rotation (degrees from normal) Alternate (see figures 6 and 8) 4

12、00 Hz Arrangement number Normal DC or 60 Hz (see figures 5 and 7) W X Y 52 02 0 - - - 52 06 0 - - - 52 12 52 13 0 300 - - FIGURE 4. Insert arrangements and rotations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14057H 5NOTES: 1. For use with co

13、nnectors under MS90555 and MS90557 utilizing socket contacts and normal keying. 2. Front face of socket insert shown. FIGURE 5. Socket contact pattern and polarization, insert in normal position (60 Hz power only). Provided by IHSNot for ResaleNo reproduction or networking permitted without license

14、from IHS-,-,-MS14057H 6NOTES: 1. For use with connectors under MS90555 and MS90557 utilizing socket contacts and alternate (W) keying. 2. Front face of socket insert shown. FIGURE 6. Socket contact pattern and polarization, insert in alternate position (400 Hz power only). Provided by IHSNot for Res

15、aleNo reproduction or networking permitted without license from IHS-,-,-MS14057H 7NOTES: 1. For use with connectors under MS90556 and MS90558 utilizing pin contacts and normal keying. 2. Front face of pin insert shown. FIGURE 7. Socket contact pattern and polarization, insert in normal position (60

16、Hz power only). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14057H 8NOTES: 1. For use with connectors under MS90556 and MS90558 utilizing pin contacts and alternate (W) keying. 2. Front face of pin insert shown. FIGURE 8. Socket contact pattern

17、 and polarization, insert in alternate position (400 Hz power only). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14057H 9REQUIREMENTS: Design and construction, see figures 1 through 8 and table I. Neutral pin (N) is not connected to shell. Grou

18、nding pin (G) is connected to shell. Applicable SAE-AS33481 crimp bushings shall be supplied with the contacts for insert arrangements as specified. TABLE I. Accessories. Contacts Cable conductors MS90556 & MS90557 Contact bushings required Insert Arrangement Quantity Size Quantity Size Quantity PIN

19、 SAE- AS33481- 52 02 2 4/0 2 2/0 2 4/0 - 2/0L 52 06 3 3 4/0 4 3 3 2/0 5(G) 3 3 4/0 - 2/0L 4 - 5L Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to

20、 MIL-DTL-22992, this document references the following: MIL-DTL-3432 MS90555 MS90556 MS90557 MS90558 SAE-AS33481 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS14057H 10CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA CC Navy EC Air

21、 Force 85 DLA CC Review activities: (Project 5935-2009-130) Army AT, AV, CR4, MI Navy AS, CG, MC, SH, YD Air Force 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-