DLA MIL-PRF-83383 1 F-2010 CIRCUIT BREAKERS REMOTE CONTROL AC-DC THERMAL TRIP-FREE SERIES TRIP SINGLE POLE (5 TO 100 AMPERES).pdf

《DLA MIL-PRF-83383 1 F-2010 CIRCUIT BREAKERS REMOTE CONTROL AC-DC THERMAL TRIP-FREE SERIES TRIP SINGLE POLE (5 TO 100 AMPERES).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-83383 1 F-2010 CIRCUIT BREAKERS REMOTE CONTROL AC-DC THERMAL TRIP-FREE SERIES TRIP SINGLE POLE (5 TO 100 AMPERES).pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5925 INCH-POUND MIL-PRF-83383/1F 29 April 2010 SUPERSEDING MIL-PRF-83383/1E 08 December 2004 PERFORMANCE SPECIFICATION SHEET CIRCUIT BREAKERS, REMOTE CONTROL, AC-DC, THERMAL, TRIP-FREE, SERIES TRIP, SINGLE POLE, (5 TO 100 AMPERES) This specification is approved for use by all Department

2、s and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-83383. FIGURE 1. Interface and physical dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

3、 IHS-,-,-MIL-PRF-83383/1F 2 1/ PIN is from National Aerospace Standard NASM315. 2/ PIN is from National Aerospace Standard NASM35338 3/ PIN is from National Aerospace Standard NAS1149. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwi

4、se specified, tolerance is .015 (0.38 mm) for three decimal places and .03 (0.76 mm) for two decimal places. 4. Stiffening webs at mounting flanges shown for reference profile as required. 5. Current rating markings may be rotated 90 degrees from the type marking shown in order to accommodate large

5、ampere ratings. FIGURE 1. Interface and physical dimensions - Continued. Current rating amperes A B +.015 -.000 C Nut 1/ Lock washer 2/ Flat washer 3/ 5 to 25 .190-32UNC-2A .500 .500 AN315-3R MS35338-43 NAS1149F0332P 35 to 100 .250-28UNF-2A .610 .610 AN315-4R MS35338-44 NAS1149F0463P Inches mm Inche

6、s mm Inches mm .005 0.13 .172 4.37 .500 12.70 .010 0.25 .180 4.57 .60 15.2 .030 0.76 .190 4.83 .610 15.49 .050 1.27 .20 5.1 .688 17.48 .056 1.42 .250 6.35 1.200 30.48 .060 1.52 .256 6.50 1.530 38.86 .061 1.55 .350 8.89 2.250 57.15 .070 1.78 .400 10.16 2.940 74.68 .084 2.13 .420 10.67 3.250 82.55 .15

7、0 3.81 .484 12.29 3.420 86.87 4.260 108.20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83383/1F 3 NOTE: Terminals 5A and 5B shall be internally grounded to the mounting flange(s). Terminals 3 and 6 shall be internally connected. FIGURE 2.

8、 Schematic. NOTE: Terminal junction system (TJS) module shall accept pin contacts P/N M39029/1-100 or -101 as specified in SAE-AS39029/1. FIGURE 3. Terminal junction system module. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83383/1F 4 TA

9、BLE I. Dash numbers and characteristics. REQUIREMENTS: Interface and physical dimensions: See figure 1. Weight: 5 to 25 amperes: 0.735 pound (334 grams), maximum. 35 to 50 amperes: 0.750 pound (341 grams), maximum. 60 to 100 amperes: 0.766 pound (348 grams), maximum. Trip indication: See figure 1. T

10、erminals: See figures 1 and 2. Voltage rating: 28 V dc or 115 V ac, 400 Hz. Current ratings: See table I. Tripping times: See table I. Response time: 25 milliseconds, maximum.Dash number Current rating (amperes) Tripping times from -54C 5C to +71C 5C (time in seconds) Percent rated current 200 400 1

11、000 Min Max Min Max Min Max 01 5.0 7 40 1.2 6.4 .3 1.2 02 7.5 11 40 2.4 6.8 .33 1.1 03 10.0 12 42 2.8 8.5 .42 1.05 04 15.0 13 45 1.7 8.3 .35 1.2 05 20.0 14 46 2.9 7.6 .4 1.15 06 25.0 15 50 2.6 8.7 .4 1.3 07 35.0 16 55 2.8 8.3 .35 1.3 08 40.0 16 55 2.9 9.2 .36 1.3 09 50.0 13 55 2.9 10 .4 1.25 10 60.0

12、 13 60 2.6 13 .26 1.8 11 75.0 13 60 2.5 13 .26 1.8 12 80.0 14 60 2.7 12.5 .3 2 13 100.0 17 63 3.5 13 .35 1.9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83383/1F 5 Power requirements and response time at minimum voltage: Standby current d

13、rain and actuation current: Test voltage: 28 0.5 V dc to TJS module, then 115 2 V ac, 400 Hz to line terminal. Actuating current, 3.5 amperes dc and 11 amperes ac rms maximum. Maximum operating time at minimum voltage: Test voltage: 18 V dc then 104 V ac rms, 400 Hz, maximum. Endurance: Electrical:

14、5 to 25 amperes: 50,000 cycles resistive or inductive or motor load or lamp load. 35 to 50 amperes: 50, 000 cycles resistive or inductive or motor load or 25,000 cycles lamp load. 60 to 100 amperes: 50,000 cycles resistive or inductive load or 25,000 cycles motor load. Interrupting capacities: A - 3

15、,600 amperes. B - 3,600 amperes. C - 3,600 amperes. D - 3,600 amperes. Other marking: Current rating: See figure 1. Line and load terminals: See figure 1. Terminal junction system (TJS) module: See figure 3. Position indication: See figure 1. Indication is provided by a lens over “open” and “closed”

16、 on red and green background. Part or Identifying Number (PIN): M83383/01- (dash number from table I) (e.g., M83383/01-01). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83383/1F 6 Indicator/control unit (I/CU): In order to maintain compati

17、bility between the RCCB and the I/CU, the following must be observed when making an I/CU selection: a. The I/CU must be a ampere rated circuit breaker (MS22073-1/2 or MS26574-1/2, as specified in SAE-AS58091, or equivalent). b. The line impedance (terminal 3 to I/CU) plus the I/CU impedance plus I/C

18、U to ground connection. c. The I/CU must respond to a decreasing current pulse of I2t 2 throughout the temperature range. CAUTION TO USERS: Coordination between devices supplied by different manufacturers should be verified by the user. Referenced documents. In addition to MIL-PRF-83383, this docume

19、nt references the following: NASM315 NASM35338 NAS1149 SAE-AS58091 SAE-AS39029/1 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for an

20、y inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Forc

21、e - 85 (Project 5925-2010-025) DLA - CC Review activities: Army - AT, AV, CR4 Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-