DLA MIL-PRF-19207 13 J-2013 FUSEHOLDERS EXTRACTOR POST TYPE NONINDICATING TYPE FHN23W.pdf

《DLA MIL-PRF-19207 13 J-2013 FUSEHOLDERS EXTRACTOR POST TYPE NONINDICATING TYPE FHN23W.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-19207 13 J-2013 FUSEHOLDERS EXTRACTOR POST TYPE NONINDICATING TYPE FHN23W.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5920 MIL-PRF-19207/13J 12 December 2013 SUPERSEDING MIL-PRF-19207/13H 24 April 2007 PERFORMANCE SPECIFICATION SHEET FUSEHOLDERS, EXTRACTOR POST TYPE, NONINDICATING, TYPE FHN23W This specification is approved for use by all Departments and Agencies of the Department of Defense The requir

2、ements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-19207. See notes on page 2. FIGURE 1. Type FHN23W fuseholder. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/13J 2 Ltr I

3、nches mm Ltr Inches mm Min Max Min Max Min Max Min Max A .175 .185 4.45 4.70 G .845 .865 21.46 21.97 B 1.307 1.317 33.20 33.45 H .860 .900 21.84 22.86 C 1.760 1.800 44.70 45.72 J - 2.680 - 68.07 D 1.180 1.220 29.97 30.99 K .870 .910 22.10 23.11 E 1.010 1.050 25.65 26.67 L .185 .195 4.70 4.95 F .110

4、.120 2.79 3.05 M 1.307 1.317 33.20 33.45 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .02 (0.5 mm) for two-place decimals and .005 (0.13 mm) for three-place decimals. 4. Marking on fuseholder cap shall

5、 be raised lettering (3 places). FIGURE 1. Type FHN23W fuseholder - continued. REQUIREMENTS: Interface and physical dimensions: See figure 1. Cap and body molding material: Cap and body molding materials shall be selected to enable the fuseholder to meet the performance requirements of this specific

6、ation. Additional information and guidance on body molding material are specified in the notes. Fuse accommodation: Ferrule type: Size: 0.406 inch (10.31 mm) diameter, 1.500 inches (38.10 mm) length. Style: F09: MIL-PRF-15160/9, F60: MIL-PRF-15160/60. (or equivalent size and style) Poles: One. Ratin

7、g: 30 amperes, 500 volts maximum. Panel thickness: 0.187 inch (4.75 mm) maximum. Lamp series resistor: None. Terminals: Solder lug type. Enclosure: Watertight. Test fuses: Temperature rise: F09A250V30A of MIL-PRF-15160/9. Short circuit: F60C500V30A of MIL-PRF-15160/60. Mechanical shock: Method II of

8、 MIL-PRF-19207. Terminal strength: 5 pounds. Torque: Cap insert: 15 pounds-inch. Salt spray (corrosion): Test condition B. Endurance: 300 operations. Mounting hardware: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/13J 3 Screw: Self-s

9、ealing panhead, slotted, stainless steel 8-32NC-2A, .625 inch (15.88 mm) long. Nut: Hexagonal, .125 inch (3.18 mm) thick stainless steel. Part or Identifying Number (PIN): FHN23W. NOTES: Cap and body molding material: It is recommended that types MAI-60, GDI-30F or SDG-F of American Society for Test

10、ing and Materials ASTM-D5948 be considered for meeting the cap and body molding material requirements of this specification. Mounting hardware and gasket: The mounting hardware and gasket shall be supplied loose in a plastic bag. Referenced documents. In addition to MIL-PRF-19207, this document refe

11、rences the following: MIL-PRF-15160/9 MIL-PRF-15160/60 ASTM-D5948 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies

12、in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing Activity: Army - CR DLA - CC Navy - SH Air force - 85 (Project

13、 5920-2012-061) DLA - CC Review activities: Army - EA, MI Navy - AS, MC Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-