DLA MIL-DTL-55302 66 G (1)-2011 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES RECEPTACLE SOCKET CONTACTS DECADE INCREMENTS 10 THRU 70 CONTACT POSITIONS AND INTERMEDIATE PO.pdf

《DLA MIL-DTL-55302 66 G (1)-2011 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES RECEPTACLE SOCKET CONTACTS DECADE INCREMENTS 10 THRU 70 CONTACT POSITIONS AND INTERMEDIATE PO.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-55302 66 G (1)-2011 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES RECEPTACLE SOCKET CONTACTS DECADE INCREMENTS 10 THRU 70 CONTACT POSITIONS AND INTERMEDIATE PO.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 MIL-DTL-55302/66G w/AMENDMENT 1 31 March 2011 SUPERSEDING MIL-DTL-55302/66G 3 February 2004 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: RECEPTACLE, SOCKET CONTACTS, DECADE INCREMENTS 10 THRU 70 CONTACT POSITIONS AND INTERMEDIATE POSITIONS OF

2、14, 24, 44, 54 AND 26, 36, 56, 66 FOR PRINTED WIRING BOARDS (.100 SPACING) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-55302. FIG

3、URE 1. Connectors, receptacle, .100 (2.54 mm) spacing. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/66G w/AMENDMENT 1 2 Inches mm Inches mm Inches mm Inches mm .001 0.03 .030 0.76 .130 3.30 .250 6.35 .006 0.15 .075 1.91 .1

4、50 3.81 .500 12.70 .008 0.20 .078 1.98 .161 4.09 .585 14.86 .010 0.25 .086 2.18 .187 4.76 .700 17.78 .025 0.64 .100 2.54 .200 5.08 FIGURE 1. Connectors, receptacle, .100 (2.54 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M

5、IL-DTL-55302/66G w/AMENDMENT 1 3 Number of contacts A .010 BSC B REF C 10 .850 (21.59) .650 (16.51) .400 (10.16) 14 1.050 (26.67) .850 (21.59) .600 (15.24) 20 1.350 (34.29) 1.150 (29.21) .900 (22.86) 24 1.550 (39.37) 1.350 (34.29) 1.100 (27.94) 26 1.650 (41.91) 1.450 (36.83) 1.200 (30.48) 30 1.850 (

6、46.99) 1.650 (41.91) 1.400 (35.56) 36 2.150 (54.61) 1.950 (49.53) 1.700 (43.18) 40 2.350 (56.69) 2.150 (54.61) 1.900 (48.26) 44 2.550 (64.77) 2.350 (56.69) 2.100 (53.35) 50 2.850 (72.39) 2.650 (67.31) 2.400 (60.96) 54 3.050 (85.09) 2.850 (72.39) 2.600 (66.04) 56 3.150 (80.01) 2.950 (74.93) 2.700 (68

7、.58) 60 3.350 (85.09) 3.150 (80.01) 2.900 (73.66) 66 3.650 (92.71) 3.450 (87.63) 3.200 (81.28) 70 3.850 (97.79) 3.650 (92.71) 3.400 (86.36) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm). 4. These

8、 connectors mate with connectors specified in MIL-DTL-55302/57, MIL-DTL-55302/61, MIL-DTL-55302/63 using appropriate hardware. 5. Numbers indicating the first and last position in each row and every fourth contact position in between shall be marked on the side(s) of the connector. As and option to

9、the above, numbers indicating every fourth cavity may be stamped on the side of the connector, with the exception that the number one contact shall be marked. 6. Termination layout on .025 (0.64 mm) modular grid. 7. Metric equivalents are in parentheses. 8. Contacts M55302/65-01 (standard force) and

10、 M55302/65-02 (low force) are individual contacts shipped loose in a plastic bag unless otherwise specified (see MIL-DTL-55302/65). Contacts may be ordered separately. 9. Hole depth to female guide hardware is .282 min (7.16 mm). Full thread depth to female threaded hardware is .240 min (6.1 mm). FI

11、GURE 1. Connectors, receptacle, .100 (2.54 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/66G w/AMENDMENT 1 4 Requirements: Dimensions and configuration: See figure 1. Material: Jackscrews and jack sockets shal

12、l be made of corrosion resisting stainless steel in accordance with ASTM A581/A581M or ASTM A582/A582M passivated in accordance with SAE-AMS2700 or shall be corrosion resistant copper nickel alloy (61 2% nickel, 2.5% max. other, and the balance zinc and shall have a brinell hardness of 145 to 175. P

13、lating: The contact plating shall be in accordance with MIL-DTL-55302 or gold in accordance with ASTM B488 type II, code C, class 1.27, over nickel plating in accordance with SAE-AMS-QQ-N-290, class 2, 50 to 150 microinches in the engaging area and gold in accordance with ASTM B488 type II, code C,

14、class 0.51, or type III, code A, 0.51 over nickel plating in accordance with SAE-AMS-QQ-N-290, class 2, 50 to 150 microinches in the termination area. Contact identification: See figure 1. Contact engagement and separation forces (number 22 contacts): Minimum separation: 0.5 ounce. Maximum engagemen

15、t: 12.0 ounces for standard force and 4.0 ounces for low force. Mating and unmating: Standard insertion force contacts: The maximum mating force, in pounds, shall be the number of contacts multiplied by 0.56 and the withdrawal force, in pounds, shall be a minimum of 0.08 times the number of contacts

16、 and shall not exceed the measured insertion force. Low insertion force contacts: The maximum mating force, in pounds, shall be the number of contacts multiplied by 0.25 and the withdrawal force, in pounds, shall be a minimum of 0.04 times the number of contacts and shall not exceed the maximum inse

17、rtion force. NOTE: Not applicable when mating and unmating is accomplished through the engaging of turning jacksets. Jackscrew and jack socket torque: 2-inch pounds maximum fully mated. Contact resistance: The average contact resistance of all contacts measured shall not exceed 0.010 ohm, and no ind

18、ividual contact pair shall have a resistance exceeding 0.020 ohm. Dielectric withstanding voltage: Sea level: 1,000 volts rms. High altitude: 300 volts rms. Current rating: 5.0 amperes maximum in accordance with contact. Insertion and removal tool: MIL-I-81969/12. Crimp tool: M22520/2-01 Provided by

19、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/66G w/AMENDMENT 1 5 Example of Part or Identifying Number (PIN): M55302/66 L 10 L Basic number of Type of contacts Number of Type of mounting specification sheet contacts hardware (see figure 1) L =

20、Low insertion (Contacts supplied with L = .700 slotted turning jackset force contacts connector are crimp M = .500 slotted turning jackset removable type for no. S = .200 slotted turning jackset - = Standard insertion 22 maximum wire size F = fixed jackset force contacts .048 maximum insulation) H =

21、 hex turning jackset Amendment notations. The margins of this specification are marked with vertical lines to indicate modifications generated by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders an

22、d contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Referenced documents. In addition to MIL-DTL-55302, this document references the following documents: MIL-DTL-55302/57 MIL-DTL-55302/61 MIL-DTL-55302/63 MIL-D

23、TL-55302/65 MIL-I-81969/12 ASTM A581/A581M ASTM A582/A582M ASTM B488 SAE-AMS2700 SAE-AMS-QQ-N-290 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/66G w/AMENDMENT 1 6 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC

24、 Navy - EC Air Force - 85 (Project 5935-2010-152) NASA - NA DLA - CC Review activities: Army - AR, AT, AV, CR4, MI Navy - AS, MC, OS, TD Air Force - 19, 99NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-