DLA MIL-DTL-55302 60 J (1)-2011 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES RECEPTACLE SOCKET CONTACTS DECADE INCREMENTS 90 100 and 120 CONTACT POSITIONS ( 100 SPACING).pdf
《DLA MIL-DTL-55302 60 J (1)-2011 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES RECEPTACLE SOCKET CONTACTS DECADE INCREMENTS 90 100 and 120 CONTACT POSITIONS ( 100 SPACING).pdf》由会员分享,可在线阅读,更多相关《DLA MIL-DTL-55302 60 J (1)-2011 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES RECEPTACLE SOCKET CONTACTS DECADE INCREMENTS 90 100 and 120 CONTACT POSITIONS ( 100 SPACING).pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、AMSC N/A FSC 5935 MIL-DTL-55302/60J w/AMENDMENT 1 31 March 2011 SUPERSEDING MIL-DTL-55302/60J 3 February 2004 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: RECEPTACLE, SOCKET CONTACTS, DECADE INCREMENTS 90, 100 and 120 CONTACT POSITIONS (.100 SPACING) This speci
2、fication is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-55302. FIGURE 1. Connectors, receptacle, .100 (2.54 mm) spacing. INCH-POUND Provided by IHSNot
3、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/60J w/AMENDMENT 1 2 FIGURE 1. Connectors, receptacle, .100 (2.54 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/60J w
4、/AMENDMENT 1 3 FIGURE 1. Connectors, receptacle, .100 (2.54 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/60J w/AMENDMENT 1 4 FIGURE 1. Connectors, receptacle, .100 (2.54 mm) spacing - Continued. Provided by I
5、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/60J w/AMENDMENT 1 5 Inches mm Inches mm Inches mm Inches mm .001 0.03 .030 0.76 .094 2.39 .172 4.37 .002 0.05 .032 0.81 .100 2.54 .200 5.08 .005 0.13 .035 0.89 .110 2.79 .225 5.72 .006 0.15 .051 1.30 .
6、120 3.05 .234 5.94 .008 0.20 .058 1.47 .125 3.18 .250 6.35 .010 0.25 .075 1.91 .130 3.30 .335 8.51 .025 0.64 .078 1.98 .140 3.56 .350 8.89 .027 0.69 .082 2.08 .150 3.81 .625 15.88 .028 0.71 .086 2.18 .161 4.09 Number of contacts Dimensions BSC A BSC B .010 C .010 D REF E REF F REF G 90 2.475 (62.87)
7、 2.700 (68.58) 5.650 (143.51) 5.150 (130.81) 2.200 (55.88) 2.100 (53.34) .400 (10.16) 100 2.725 (69.22) 2.950 (74.93) 6.150 (156.21) 5.650 (143.51) 2.400 (60.95) 2.400 (60.95) .400 (10.16) 120 3.225 (81.92) 3.450 (87.63) 7.150 (181.61) 6.650 (168.91) 2.900 (73.66) 2.900 (73.66) .400 (10.16) NOTES: 1
8、. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm). 4. These connectors mate with connectors specified in MIL-DTL-55302/59. 5. Numbers indicating the first and last position in each row and every fourth conta
9、ct position in between shall be marked on the side(s) of the connector. As an option to the above, numbers indicating every fourth cavity may be stamped on the side of the connector, with the exception that the number one contact shall be marked. 6. Termination layout on .025 (0.64 mm) modular grid.
10、 7. Metric equivalents are in parentheses. 8. Hole depth to female guide hardware is .282 min (7.16 mm). Full thread depth to female threaded hardware is .240 min (6.1 mm). FIGURE 1. Connectors, receptacle, .100 (2.54 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networkin
11、g permitted without license from IHS-,-,-MIL-DTL-55302/60J w/AMENDMENT 1 6 Requirements: Dimensions and configuration: See figure 1. Material: Guide pins, type X guide sockets, jackscrews and jack sockets shall be made of corrosion resisting stainless steel in accordance with ASTM A581/A581M or ASTM
12、 A582/A582M passivated in accordance with SAE-AMS2700 or shall be corrosion resistant copper nickel alloy (61 2% nickel, 2.5% max. other, and the balance zinc and shall have a brinell hardness of 145 to 175. Type Y guide sockets shall be beryllium copper in accordance with ASTM B196/B196M or ASTM B1
13、97/B197M, nickel plated in accordance with SAE-AMS-QQ-N-290, class 2, 50 to 150 microinches. Plating: The contact plating shall be in accordance with MIL-DTL-55302 or gold in accordance with ASTM B488 type II, code C, class 1.27, over nickel plating in accordance with SAE-AMS-QQ-N-290, class 2, 50 t
14、o 150 microinches in the engaging area and gold in accordance with ASTM B488 type II, code C, class 0.51, or type III, code A, 0.51 over nickel plating in accordance with SAE-AMS-QQ-N-290, class 2, 50 to 150 microinches in the termination area. Contact identification: See figure 1. Contact engagemen
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILDTL5530260J12011CONNECTORSPRINTEDCIRCUITSUBASSEMBLYANDACCESSORIESRECEPTACLESOCKETCONTACTSDECADEINCREMENTS90100AND120CONTACTPOSITIONS100SPACINGPDF

链接地址:http://www.mydoc123.com/p-691011.html