DLA MIL-DTL-3970 16 C-2008 WAVEGUIDE ASSEMBLIES RIGID 90-DEGREE H-PLANE MITERED CORNER《刚性90度H面切角弯波导组装》.pdf

《DLA MIL-DTL-3970 16 C-2008 WAVEGUIDE ASSEMBLIES RIGID 90-DEGREE H-PLANE MITERED CORNER《刚性90度H面切角弯波导组装》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-3970 16 C-2008 WAVEGUIDE ASSEMBLIES RIGID 90-DEGREE H-PLANE MITERED CORNER《刚性90度H面切角弯波导组装》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-DTL-3970/16C 28 April 2008 SUPERSEDING MIL-W-3970/16B 4 April 1977 DETAIL SPECIFICATION SHEET WAVEGUIDE ASSEMBLIES, RIGID, 90-DEGREE H-PLANE MITERED CORNER This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. Requirements for acquiring the waveg

2、uide assemblies described herein shall consist of this document and MIL-DTL-3970. FIGURE 1. Assembly configuration. AMSC N/A FSC 5985INCH-POUND Inactive for new design after 18 September 1998. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I.

3、Dash number, electrical and physical characteristics, and dimensions. Flange 1 2 Dimensions 1/ 2/ 3/ Dash no. Wave- guide M85/ M3922/ Frequency range TE10mode Insertionloss max VSWRmax Pressur-ization lbf/in2gauge A B C Pin dia B E F G 001 1-043 56-001 61-002 GHz 2.60 - 3.95 dB .05 1.09 15 4.225 (10

4、7.32) .020 (0.51) 2.625 (66.68) .015 (0.38) .278 (7.06) .005 (0.13) .394 (10.01) .005 (0.13) 4.384 (111.35) .020 (0.51) .060 (1.52) .012 (0.30) 002 1-055 57-002 62-002 3.95 - 5.85 .05 1.08 30 2.924 (74.57) .020 (0.51) 1.875 (47.63) .015 (0.38) .184 (4.67) .005 (0.13) .260 (6.60) .005 (0.13) 2.898 (7

5、3.61) .020 (0.51) .041 (1.04) .008 (0.20) 003 1-067 55-001 60-001 5.85 - 8.20 .05 1.08 30 2.139 (54.33) .015 (0.38) 1.375 (34.93) .010 (0.25) .136 (3.45) .003 (0.08) .190 (4.83) .003 (0.08) 2.141 (54.38) .015 (0.38) .032 (0.81) .006 (0.15) 004 1-073 53-002 59-007 7.05 - 10.0 .06 1.08 30 1.869 (47.47

6、) .015 (0.38) 1.250 (31.75) .010 (0.25) .110 (2.79) .002 (0.05) .156 (3.96) .002 (0.05) 1.760 (44.70) .015 (0.38) .024 (0.61) .005 (0.13) 005 1-079 53-001 59-006 8.20 - 12.40 .06 1.10 30 1.370 (34.80) .010 (0.25) 0.875 (22.23) .010 (0.25) .088 (2.24) .002 (0.05) .125 (3.18) .002 (0.05) 1.410 (35.81)

7、 .010 (0.25) .019 (0.48) .004 (0.10) 006 1-102 54-001 59-003 18.0 - 26.50 .11 1.06 30 .775 (19.69) .010 (0.25) .550 (13.97) .010 (0.25) .040 (1.02) .002 (0.05) .0580 (1.47) .0005 (0.01) .672 (17.07) .010 (0.25) .011 (0.28) .002 (0.05) 007 1-106 54-001 59-003 18.0 - 26.50 .11 1.06 30 .775 (19.69) .01

8、0 (0.25) .550 (13.97) .010 (0.25) .040 (1.02) .002 (0.05) .0580 (1.47) .0005 (0.01) .672 (17.07) .010 (0.25) .011 (0.28) .002 (0.05) 008 1-077 53-003 59-008 8.20 - 12.40 .06 1.10 30 1.370 (34.80) .010 (0.25) .875 (22.23) .010 (0.25) .088 (2.24) .002 (0.05) .125 (3.18) .002 (0.05) 1.410 (35.81) .010

9、(0.25) .019 (0.48) .004 (0.10) See footnotes at end of table. MIL-DTL-3970/16C2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Dash number, electrical and physical characteristics, and dimensions - Continued. Flange 1 2 Dimensions 1/ 2/ 3/

10、Dash no. Wave- guide M85/ M3922/ Frequencyrange TE10modeInsertionloss max VSWRmax Pressur-ization lbf/in2gauge A B C Pin dia B E F G 009 1-071 53-004 59-009 GHz 7.05 - 10.0dB .06 1.08 30 1.869 (47.47) .015 (0.38) 1.250 (31.75) .010 (0.25) .110 (2.79) .002 (0.05) .156 (3.96) .002 (0.05) 1.760 (44.70)

11、 .015 (0.38) .024 (0.61) .005 (0.13) 010 1-041 56-002 61-001 2.60 - 3.95 .05 1.09 15 4.225 (107.32) .020 (0.51) 2.626 (66.68) .015 (0.38) .278 (7.60) .005 (0.13) .394 (10.01) .005 (0.13) 4.384 (111.35) .020 (0.51) .060 (1.52) .012 (0.30) 011 1-089 53-005 59-001 12.4 - 18.0 .07 1.10 30 1.091 (27.71)

12、.010 (0.25) .750 (19.05) .010 (0.25) .060 (1.52) .002 (0.05) .087 (2.21) .001 (0.03) .978 (24.84) .010 (0.25) .015 (0.38) .003 (0.08) 012 1-053 57-001 62-001 3.95 - 5.85 .05 1.08 30 2.924 (74.57) .020 (0.51) 1.875 (47.63) .015 (0.38) .184 (4.67) .005 (0.13) .260 (6.60) .005 (0.13) 2.898 (73.61) .020

13、 (0.51) .041 (1.04) .008 (0.20) 013 3-006 54-003 59-005 26.5 - 40.0 .15 1.12 30 .645 (16.38) .010 (0.25) .500 (12.70) .010 (0.25) .027 (0.69) .002 (0.05) .0390 (0.99) .0005 (0.01) .459 (11.66) .010 (0.25) .009 (0.23) .001 (0.03) 014 1-065 55-002 60-002 5.85 - 8.20 .05 1.08 30 2.139 (54.33) .015 (0.3

14、8) 1.375 (34.93) .010 (0.25) .136 (3.45) .003 (0.08) .190 (4.83) .003 (0.08) 2.141 (54.38) .015 (0.38) .032 (0.81) .006 (0.15) 015 1-093 53-005 59-001 12.4 - 18.0 .07 1.10 30 1.091 (27.71) .010 (0.25) .750 (19.05) .010 (0.25) .060 (1.52) .002 (0.05) .087 (2.21) .001 (0.03) .978 (24.84) .010 (0.25) .

15、015 (0.38) .003 (0.08) 016 1-103 54-002 59-004 18.0 - 26.5 .11 1.06 30 .775 (19.69) .010 (0.25) .550 (13.97) .010 (0.25) .040 (1.02) .002 (0.05) .0580 (1.47) .0005 (0.01) .672 (17.07) .010 (0.25) .011 (0.28) .002 (0.05) 1/ Dimensions are in inches. 2/ Metric equivalents (to the nearest .01 mm) are g

16、iven for general information only and are based upon 1 inch = 25.4 mm. 3/ Metric equivalents are in parentheses. MIL-DTL-3970/16C3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3970/16C 4 REQUIREMENTS: Dimensions and configuration: See figu

17、re 1 and table I. Electrical characteristics: See table I. Part or Identifying Number (PIN): M3970/16-(dash number from table I). Cross reference: See table II. TABLE II. Cross reference. PIN M3970/16- Type designation PIN M3970/16- Type designation 001 002 003 004 005 006 007 008 UG-844/U UG-845/U

18、UG-846/U UG-847/U UG-848/U UG-849/U UG-850/U UG-851/U 009 010 011 012 013 014 015 016 UG-852/U UG-853/U UG-854/U UG-855/U UG-856/U UG-857/U UG-858/U UG-859/U Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to th

19、e extent of the changes. Referenced documents. This specification sheet references only MIL-DTL-3970. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 11 (Project 5985-2008-035) DLA - CC Review activities: Army - AR, MI Navy - AS, CG, MC, OS Air Force - 19, 99 NOTE: The activ

20、ities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-