DLA A-A-59374-2000 DECALS (HEAT TRANSFER) USMC [Superseded DLA MIL-D-29362 B CANC NOTICE 1 DLA MIL-D-29362 B DLA MIL-D-29362 A DLA MIL-D-29362 (1) DLA MIL-D-29362]《美国海军陆战队(传热)识别标记(.pdf

《DLA A-A-59374-2000 DECALS (HEAT TRANSFER) USMC [Superseded DLA MIL-D-29362 B CANC NOTICE 1 DLA MIL-D-29362 B DLA MIL-D-29362 A DLA MIL-D-29362 (1) DLA MIL-D-29362]《美国海军陆战队(传热)识别标记(.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59374-2000 DECALS (HEAT TRANSFER) USMC [Superseded DLA MIL-D-29362 B CANC NOTICE 1 DLA MIL-D-29362 B DLA MIL-D-29362 A DLA MIL-D-29362 (1) DLA MIL-D-29362]《美国海军陆战队(传热)识别标记(.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDA-A-5937426 May 2000 SUPERSEDINGMIL-D-29362B4 December 1991Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any datathat may improve this document should be sent to: Defense Supply Center Richmond(DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, Rich

2、mond, VA 23297-5610.AMSC N/A FSC 7690DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.DECALS (HEAT TRANSFER): USMCThe General Services Administration has authorized the use of thiscommercial item description for all federal agencies.1. SCOPE. This commercial item desc

3、ription covers requirements for the Marine Corps serviceemblem decal used on utility coats and helmet covers.2. CLASSIFICATION. The decal shall be the heat transfer type.3. SALIENT CHARACTERISTICS3.1 Decal. The decal shall be printed on 4-1/2 inch wide white transparent transfer paper using ablack,

4、resin printing medium. The design shall be the United States Marine Corps emblem asshown in figure 1.3.2 Printed method. The printed method shall allow for application in accordance with 3.4.3.3 Put up. The decals shall be put up (wound) on cardboard tubes with 1,000 decals per roll.An appropriate i

5、nstruction/caution sheet conforming to figure 2, shall be inserted alternatelybetween the decals in the roll. Horizontal tear line markings shall be provided every 5-1/4 inchesbetween each decal and instruction/caution sheet. The decals shall be placed on the tightlywound roll as shown in figure 3.3

6、.4 Application. The decals shall be designed to be applied by a dry heat process so that theinitial print is well defined and clearly legible without smearing, bleeding or offsetting. A handiron or automatic thermopress no greater than 300F is used to apply the decals.3.5 Colorfastness. Ink transfer

7、 to the utility coats and helmet covers shall be full and uniform,free from grayness, pinpoints or other imperfections. The ink shall show fastness to laundering(after 3 cycles) equal to or better than a rating of 4-5 on the American Association of TextileChemists and Colorists (AATCC) Gray Scale fo

8、r Color Change and Staining when tested inaccordance with Test 2A of AATCC 61, “Colorfastness to Laundering, Home and Commercial:Accelerated“.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-593742(11964)1-3/4“4-1/2“5-1/4“2“3/4“FIGURE 1. Decal.3.6

9、 Labels. A label containing the contractors name, contract number and National StockNumber (NSN) shall be attached to the outside of each roll. In addition, a bar code label shall beattached to the outside of each roll and the outside of each shipping container. The bar code shallbe printed on press

10、ure-sensitive labels with a finish compatible with printing technology usedand shall be clearly legible and readable by a scanner.4. REGULATORY REQUIREMENTS4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with pa

11、ragraph 23.403 of the Federal AcquisitionRegulation (FAR).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-593743(11964A)Placement On Pocket1. Detach instructions from Decal.2. Press pocket free of wrinkles.3. Place decal on pocket with inked side

12、 down.4. Use dry iron set at 300F (synthetic).5. Press over decal three to four seconds. Do not use steam.6. Remove paper immediately, while paper is hot.If paper should stick, reapply iron to decal and remove paper from pocket.U.S. MARINEFIGURE 2. Instruction sheet.Provided by IHSNot for ResaleNo r

13、eproduction or networking permitted without license from IHS-,-,-A-A-593744FIGURE 3. Required winding.5. PRODUCT CONFORMANCE PROVISIONS5.1 Product conformance. The products provided shall meet the salient characteristics of thiscommercial item description, conform to the producers own drawings, spec

14、ifications, standards,and quality assurance practices, and be the same product offered for sale in the commercialmarketplace. The government reserves the right to require proof of such conformance.5.2 Standard sample. Standard samples may be furnished and are solely for guidance andinformation to th

15、e contractor. Variation from this specification may appear in the standardsample in which case this specification shall govern.5.3 Responsibility for inspection. Unless otherwise specified in the contract (see 7.3(b), thecontractor is responsible for the performance of all required inspections and m

16、ay use his or anyother suitable facilities for the performance of the required inspections.U.S. MARINE1. Detach instructions from Decal.2. Press pocket free of wrinkles.3. Place decal on pocket with inked side down.4. Use dry iron set at 300F (synthetic).5. Press over decal three to four seconds. Do

17、 not use steam.6. Remove paper immediately, while paper is hot.If paper should stick, reapply iron to decal and remove paper from pocket.U.S. MARINE2. Press pocket 3. Place decal on pocket with 4. Use dry iron set at 300F (synthetic).5. Press over decal three to four seconds. Do not use s6. Remove p

18、aper immediately, while paper is hot.If paper should stick, reapply iron to decal and remove paper from pocket.(12215)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5937456. PACKAGING6.1 Preservation, packing, and marking. For acquisition purpos

19、es, the decals shall be preserved,packed, and marked as specified in the acquisition order (see 7.3(c).7. NOTES7.1 Part or identification number (PIN). The part or identification numbering procedure for thisCID is A-A-59374-1. It is for government purposes and does not constitute a requirement for t

20、hecontractor.7.2 National stock number (NSN). This CID is associated with NSN 7690-01-060-7503. OtherNSNs may also correspond with this document.7.3 Ordering data. Acquisition documents must specify the following information:a. CID document number, revision, and CID PINb. Inspections, if different (

21、see 5.3)c. Preservation, packing and marking instructions (see 6.1)7.4 Sources of documents.7.4.1 FAR. The FAR may be obtained from the Superintendent of Documents, U.S.Government Printing Office, Washington, DC 20402-0001.7.4.2 AATCC test methods. Copies of AATCC test methods may be obtained from t

22、heAmerican Association of Textiles Chemists and Colorists (AATCC), One Davis Drive, P.O.Box 12215, Research Triangle Park, NC 27709-2215.MILITARY INTEREST:CIVIL AGENCYCOORDINATING ACTIVITY:Custodian:Navy - MCGSA - 2FYEPreparing activity:DLA - GS(Project 7690-0001)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-