DIN EN ISO 9712 Bb 1-2014 Non-destructive testing - Qualification and certification of NDT personnel Supplement 1 Recommendations on the application of DIN EN ISO 9712 2012-12《无损检测.pdf

《DIN EN ISO 9712 Bb 1-2014 Non-destructive testing - Qualification and certification of NDT personnel Supplement 1 Recommendations on the application of DIN EN ISO 9712 2012-12《无损检测.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 9712 Bb 1-2014 Non-destructive testing - Qualification and certification of NDT personnel Supplement 1 Recommendations on the application of DIN EN ISO 9712 2012-12《无损检测.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、May 2014 Translation by DIN-Sprachendienst.English price group 4No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 03.

2、100.30; 19.100!%1l1“2147314www.din.deDThis supplement provides information relating to DIN EN ISO 9712, but does not contain any additional specifications.DIN EN ISO 9712 Supplement 1Non-destructive testing Qualification and certification of NDT personnel; Supplement 1:Recommendations on the applica

3、tion of DIN EN ISO 9712:2012-12,English translation of DIN EN ISO 9712 Beiblatt 1:2014-05Zerstrungsfreie Prfung Qualifizierung und Zertifizierung von Personal der zerstrungsfreien Prfung; Beiblatt 1:Empfehlungen zur Anwendung von DIN EN ISO 9712:2012-12,Englische bersetzung von DIN EN ISO 9712 Beibl

4、att 1:2014-05Essais non destructifs Qualification et certification du personnel END; Supplment 1: Recommandations pourlutilisation de la norme DIN EN ISO 9712:2012-12,Traduction anglaise de DIN EN ISO 9712 Beiblatt 1:2014-05www.beuth.deDocument comprises 5 pagesIn case of doubt, the German-language

5、original shall be considered authoritative.08.14 DIN EN ISO 9712 Suppl. 1:2014-05 2 A comma is used as the decimal marker. Contents Page Foreword 3 Introduction .3 1 Scope 4 2 References 4 3 Approval of instructional content of vocational training.4 4 Infrared thermography 4 DIN EN ISO 9712 Suppl. 1

6、:2014-05 3 Foreword This document has been prepared by Working Committee NA 062-08-21 AA Qualifizierung und Zertifizierung von Personal der zerstrungsfreien Prfung of the Normenausschuss Materialprfung (NMP) (Materials Testing Standards Committee). Introduction In order to receive NDT personnel cert

7、ification according to DIN EN ISO 9712, the candidate shall provide evidence, at a minimum, of the completion of a theoretical and practical training program which is recognized by a certification body. The training program approval procedure involves verification by the certification body that the

8、content of the instruction adheres to those specifications published regarding the training. Many certification bodies also have a formal approval process in which a training curriculum of a training establishment is appraised in advance and officially approved. A characteristic unique to Germany is

9、 the dual vocational training system. Here, future skilled workers receive a comprehensive theoretical and practical training, which for some jobs also includes instruction in non-destructive testing methods. If these parts of the training program (e.g. vocational training as a materials tester) are

10、 to be certified as theoretical and practical training in compliance with DIN EN ISO 9712, they are also required to be appraised by the certification body. Because of legally established divisions of responsibility, the certification bodies are not able to directly appraise vocational training scho

11、ols in a formal approval process or to perform regular assessments. Thus, such training programs are approved on the basis of suitable evidence. This supplement provides a recommendation for a uniform approval procedure. In addition, this supplement gives detailed recommendations on the allocation o

12、f minimum training times in various areas involving infrared thermographic methods. DIN EN ISO 9712 Suppl. 1:2014-05 4 1 Scope This supplement provides recommendations on how to receive approval of the instructional content of vocational training (in vocational schools) relating to the qualification

13、 examination for the certification of NDT personnel, as well as the minimum training times for training in infrared thermography methods according to DIN EN ISO 9712:2012-12. 2 References The following documents, in whole or in part, are normatively referenced in this document and are indispensable

14、for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN EN ISO 9712:2012-12, Non-destructive testing Qualification and certification of NDT personnel (ISO 9712:2012) 3 App

15、roval of instructional content of vocational training In the framework of certification in compliance with DIN EN ISO 9712:2012-12, (starting August 1, 2013) instructional training content can be approved which has been successfully completed as part of the “materials tester” job qualification in th

16、e dual vocational training system. In this case, the report booklet provides adequate proof of proper training according to 14 Abs. 1 Nr. 4 Berufsbildungsgesetz (Vocational training law - BBiG), which stipulates that trainees are to be encouraged to keep a documentation of their training. In additio

17、n to the report booklet, proof of NDT-specific training and tasks shall be provided. It shall be left to the discretion of the certification body to specify additional measures necessary prior to the admission of a candidate to qualification examinations in the individual NDT methods. 4 Infrared the

18、rmography It is recommended that methods of infrared thermography be divided into the following fields of application: building construction; electrical engineering; general industry passive thermography; general industry active thermography. Irrespective of the field, a minimum training time of 40

19、h in Level 1 should be completed. In Level 2, training times as outlined in Table 1 are recommended. DIN EN ISO 9712 Suppl. 1:2014-05 5 Table 1 Recommended minimum training in Level 2 for infrared thermography Scope Level 2 h Basic training 16 Building construction 24 Electrical engineering 24 General industry passive thermography 24 General industry active thermography 24