DIN EN ISO 4035-2013 Hexagon thin nuts chamfered (style 0) - Product grades A and B (ISO 4035 2012) German version EN ISO 4035 2012《倒角六角薄螺母(0型) 产品等级A和B级 德文版本EN ISO 4035-2012》.pdf

《DIN EN ISO 4035-2013 Hexagon thin nuts chamfered (style 0) - Product grades A and B (ISO 4035 2012) German version EN ISO 4035 2012《倒角六角薄螺母(0型) 产品等级A和B级 德文版本EN ISO 4035-2012》.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 4035-2013 Hexagon thin nuts chamfered (style 0) - Product grades A and B (ISO 4035 2012) German version EN ISO 4035 2012《倒角六角薄螺母(0型) 产品等级A和B级 德文版本EN ISO 4035-2012》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、April 2013Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 21

2、.060.20!$P“1999345www.din.deDDIN EN ISO 4035Hexagon thin nuts chamfered (style 0) Product grades A and B (ISO 4035:2012);English version EN ISO 4035:2012,English translation of DIN EN ISO 4035:2013-04Niedrige Sechskantmuttern mit Fase (Typ 0) Produktklassen A und B (ISO 4035:2012);Englische Fassung

3、EN ISO 4035:2012,Englische bersetzung von DIN EN ISO 4035:2013-04crous bas hexagonaux chanfreins (style 0) Grades A et B (ISO 4035:2012);Version anglaise EN ISO 4035:2012,Traduction anglaise de DIN EN ISO 4035:2013-04SupersedesDIN EN ISO 4035:2001-03www.beuth.deIn case of doubt, the German-language

4、original shall be considered authoritative.Document comprises 14 pages03.13 DIN EN ISO 4035:2013-04 2 A comma is used as the decimal marker. National foreword This document (EN ISO 4035:2012) has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/

5、TC 185 “Fasteners” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Mechanische Verbindungs-elemente (Fasteners Standards Committee), Working Committee NA 067-00-03 AA Verbindungselemente mit metrischem Innengewinde. The DIN Standards corre

6、sponding to the International Standards referred to in this document are as follows: ISO 225 DIN EN ISO 225 ISO 724 DIN ISO 724 ISO 898-2 DIN EN ISO 898-2 ISO 965-1 DIN ISO 965-1 ISO 3269 DIN EN ISO 3269 ISO 3506-2 DIN EN ISO 3506-2 ISO 4042 DIN EN ISO 4042 ISO 4759-1 DIN EN ISO 4759-1 ISO 6157-2 DI

7、N EN ISO 6157-2 ISO 8839 DIN EN 28839 ISO 8992 DIN ISO 8992 ISO 10683 DIN EN ISO 10683 ISO 10684 DIN EN ISO 10684 ISO 16048 DIN EN ISO 16048 Amendments This standard differs from DIN EN ISO 4035:2001-03 as follows: a) normative references are now undated; b) the letter symbol d has been replaced by

8、D (in accordance with DIN EN ISO 225 and DIN ISO 724); c) in Tables 1 and 2, the number of decimal places has been unified; d) Table 3 has been brought in line with the new edition of DIN EN ISO 898-2; e) the standard has been editorially revised and normative references have been updated. Previous

9、editions DIN 439: 1921-01, 1921-12, 1925-04, 1941-09, 1963-03, 1972-12 DIN 439-1: 1983-12 DIN 439-2: 1983-12, 1987-10 DIN ISO 4035: 1987-10 DIN EN 24035: 1992-02 DIN EN ISO 4035: 2001-03 DIN EN ISO 4035:2013-04 3 National Annex NA (informative) Bibliography DIN EN 28839, Mechanical properties of fas

10、teners Nonferrous metal bolts, screws, studs and nuts DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions DIN EN ISO 898-2, Mechanical properties of fasteners made of carbon steel and alloy steel Part 2: Nuts with specified property classes Coarse thread an

11、d fine pitch DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 3506-2, Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Pro

12、duct grades A, B and C DIN EN ISO 6157-2, Fasteners Surface discontinuities Part 2: Nuts DIN EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN EN ISO 10684, Fasteners Hot dip galvanized coatings DIN EN ISO 16048, Passivation of corrosion-resistant stainless-steel fasteners

13、 DIN ISO 724, ISO general purpose metric screw threads Basic dimensions DIN ISO 965-1, ISO general purpose metric screw threads Tolerances Part 1: Principles and basic data DIN ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts DIN EN ISO 4035:2013-04 4 This page is intention

14、ally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 4035 December 2012 ICS 21.060.20 Supersedes EN ISO 4035:2000English Version Hexagon thin nuts chamfered (style 0) - Product grades A and B (ISO 4035:2012) crous bas hexagonaux chanfreins (style 0) - Grades A Produktklassen A und B (

15、ISO 4035:2012) This European Standard was approved by CEN on 15 November 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bib

16、liographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the respo

17、nsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Rep

18、ublic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CE

19、N All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 4035:2012: Eet B (ISO 4035:2012) EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Niedrige Sechskantmuttern mit Fase (Typ 0) - Co

20、ntents Page Foreword . 3 Introduction . 4 1 Scope . 5 2 Normative references. 5 3 Dimensions . 5 4 Requirements and reference International Standards . 8 5 Designation . 8 Bibliography 9 2DIN EN ISO 4035:2013-04 EN ISO 4035:2012 (E) Foreword This document (EN ISO 4035:2012) has been prepared by Tech

21、nical Committee ISO/TC 2 in collaboration with Technical Committee CEN/TC 185 “Fasteners”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2013, and c

22、onflicting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This docu

23、ment supersedes EN ISO 4035:2000. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav

24、Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 4035:2012 has been

25、 approved by CEN as a EN ISO 4035:2012 without any modification. “Fasteners”3DIN EN ISO 4035:2013-04 EN ISO 4035:2012 (E) IntroductionThis International Standard belongs to a complete group of product standards developed by ISO on external hexagon drive fasteners. It comprises the following:a) hexag

26、on head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765);b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);c) hexagon nuts (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042, ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513);d)

27、 hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15072);e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 and ISO 21670).4DIN EN ISO 4035:2013-04 EN ISO 4035:2012 (E) 1 ScopeThis International Standard specifies the characteristics of chamfered hexagon

28、 thin nuts (style 0), with threads from M1,6 up to and including M64, with product grade A for threads D M16 and product grade B for threads D M16.If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing Internationa

29、l Standards, for example ISO 724, ISO 898-2, ISO 965-1, ISO 3506-2 and ISO 4759-1.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable to its application. For undated references, the latest edition of the referenced doc

30、ument (including any amendments) applies.ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensionsISO 724, ISO general-purpose metric screw threads Basic dimensionsISO 898-2, Mechanical properties of fasteners made of carbon steel and alloy steel Part 2: Nuts with speci

31、fied property classes Coarse thread and fine pitch threadISO 965-1, ISO general-purpose metric screw threads Tolerances Part 1: Principles and basic dataISO 3269, Fasteners Acceptance inspectionISO 3506-2, Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: NutsISO 4042, F

32、asteners Electroplated coatingsISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and CISO 6157-2, Fasteners Surface discontinuities Part 2: NutsISO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metalsISO 8992,

33、Fasteners General requirements for bolts, screws, studs and nutsISO 10683, Fasteners Non-electrolytically applied zinc flake coatingsISO 10684, Fasteners Hot dip galvanized coatings3 DimensionsSee Figure 1 and Tables 1 and 2.Symbols and descriptions of dimensions are specified in ISO 225.5DIN EN ISO

34、 4035:2013-04 EN ISO 4035:2012 (E) a = 15 to 30.b = 110 to 120.Figure 1Table 1 Preferred threadsDimensions in millimetresThread DM1,6 M2 M2,5 M3 M4 M5 M6 M8 M10 M12Pa0,35 0,4 0,45 0,5 0,7 0,8 1 1,25 1,5 1,75damax. 1,84 2,30 2,90 3,45 4,60 5,75 6,75 8,75 10,80 13,00min. 1,60 2,00 2,50 3,00 4,00 5,00

35、6,00 8,00 10,00 12,00dwmin. 2,40 3,10 4,1 4,60 5,90 6,90 8,90 11,60 14,60 16,60e min. 3,41 4,32 5,45 6,01 7,66 8,79 11,05 14,38 17,77 20,03m max. 1,00 1,20 1,60 1,80 2,20 2,70 3,20 4,00 5,00 6,00min. 0,75 0,95 1,35 1,55 1,95 2,45 2,90 3,70 4,70 5,70mwmin. 0,60 0,80 1,10 1,20 1,60 2,00 2,3 3,0 3,8 4,

36、60snom. = max. 3,20 4,00 5,00 5,50 7,00 8,00 10,00 13,00 16,00 18,00min. 3,02 3,82 4,82 5,32 6,78 7,78 9,78 12,73 15,73 17,736DIN EN ISO 4035:2013-04 EN ISO 4035:2012 (E) Table 1 (continued)Dimensions in millimetresThread DM16 M20 M24 M30 M36 M42 M48 M56 M64Pa2 2,5 3 3,5 4 4,5 5 5,5 6damax. 17,30 21

37、,60 25,90 32,40 38,90 45,40 51,80 60,50 69,10min. 16,00 20,00 24,00 30,00 36,00 42,00 48,00 56,00 64,00dwmin. 22,50 27,70 33,20 42,80 51,10 60,00 69,50 78,70 88,20e min. 26,75 32,95 39,55 50,85 60,79 71,30 82,60 93,56 104,86m max. 8,00 10,00 12,00 15,00 18,00 21,00 24,00 28,00 32,00min. 7,42 9,10 10

38、,90 13,90 16,90 19,70 22,70 26,70 30,40mwmin. 5,90 7,30 8,70 11,10 13,50 15,80 18,20 21,40 24,30snom. = max. 24,00 30,00 36,00 46,00 55,00 65,00 75,00 85,00 95,00min. 23,67 29,16 35,00 45,00 53,80 63,10 73,10 82,80 92,80aP is the pitch of the thread.Table 2 Non-preferred threadsDimensions in millime

39、tresThread DM3,5 M14 M18 M22 M27 M33 M39 M45 M52 M60Pa0,6 2 2,5 2,5 3 3,5 4 4,5 5 5,5damax. 4,00 15,10 19,50 23,70 29,10 35,60 42,10 48,60 56,20 64,80min. 3,50 14,00 18,00 22,00 27,00 33,00 39,00 45,00 52,00 60,00dwmin. 5,10 19,60 24,90 31,40 38,00 46,60 55,90 64,70 74,20 83,40e min. 6,58 23,36 29,5

40、6 37,29 45,20 55,37 66,44 76,95 88,25 99,21m max. 2,00 7,00 9,00 11,00 13,50 16,50 19,50 22,50 26,00 30,00min. 1,75 6,42 8,42 9,90 12,40 15,40 18,20 21,20 24,70 28,70mwmin. 1,40 5,10 6,70 7,90 9,90 12,30 14,60 17,00 19,80 23,00snom. = max. 6,00 21,00 27,00 34,00 41,00 50,00 60,00 70,00 80,00 90,00mi

41、n. 5,82 20,67 26,16 33,00 40,00 49,00 58,80 68,10 78,10 87,80aP is the pitch of the thread.7DIN EN ISO 4035:2013-04 EN ISO 4035:2012 (E) 4 Requirements and reference International StandardsSee Table 3.Table 3 Requirements and reference International StandardsMaterial Steel Stainless steel Non-ferrou

42、s metalGeneral requirementsInternational StandardISO 8992ThreadTolerance class 6HInternational StandardsISO 724, ISO 965-1Mechanical propertiesProperty classD M39: as agreed D M39: as agreedInternational StandardsD M39: as agreed (specified in ISO 898-2:2012, Annex A)D M39: as agreedToleranceProduct

43、 gradeD M16: AD M16: BInternational StandardISO 4759-1Finish CoatingAs processed Clean and brightA method for passivation is specified in ISO 16048.As processedRequirements for electroplating are specified in ISO 4042.Requirements for electroplating are specified in ISO 4042.Requirements for non-ele

44、ctrolytically applied zinc flake coatings are specified in ISO 10683.Requirements for hot dip galvanized coatings are specified in ISO 10684.Additional requirements or other finishes or coatings shall be agreed between the supplier and the purchaser.Surface integrityLimits for surface discontinuitie

45、s are specified in ISO 6157-2Acceptability Acceptance inspection is specified in ISO 3269.5 DesignationEXAMPLE A chamfered hexagon thin nut (style 0) with thread M12 and property class 05 is designated as follows:Hexagon thin nut ISO 4035 - M12 - 058DIN EN ISO 4035:2013-04 EN ISO 4035:2012 (E) Bibli

46、ography1 ISO 4014, Hexagon head bolts Product grades A and B2 ISO 4015, Hexagon head bolts Product grade B Reduced shank (shank diameter approximately equal to pitch diameter)3 ISO 4016, Hexagon head bolts Product grade C4 ISO 4017, Hexagon head screws Product grades A and B5 ISO 4018, Hexagon head

47、screws Product grade C6 ISO 4032, Hexagon regular nuts (style 1) Product grades A and B7 ISO 4033, Hexagon high nuts (style 2) Product grades A and B8 ISO 4034, Hexagon regular nuts (style 1) Product grade C9 ISO 4036, Hexagon thin nuts unchamfered (style 0) Product grade B10 ISO 4161, Hexagon nuts

48、with flange, style 2 Coarse thread11 ISO 4162, Hexagon flange bolts Small series Product grade A with driving feature of product grade B12 ISO 7040, Prevailing torque type hexagon regular nuts (with non-metallic insert) Property classes 5, 8 and 1013 ISO 7041, Prevailing torque type hexagon nuts (wi

49、th non-metallic insert), style 2 Property classes 9 and 1214 ISO 7042, Prevailing torque type all-metal hexagon high nuts Property classes 5, 8, 10 and 1215 ISO 7043, Prevailing torque type hexagon nuts with flange (with non-metallic insert), style 2 Product grades A and B16 ISO 7044, Prevailing torque type all-metal hexagon nuts with fl