DIN EN ISO 2580-2-2004 Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2 Preparation of test specimens and determination of properties (ISO.pdf

《DIN EN ISO 2580-2-2004 Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2 Preparation of test specimens and determination of properties (ISO.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 2580-2-2004 Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2 Preparation of test specimens and determination of properties (ISO.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、ICS 83.080.20PlasticsAcrylonitrile-butadiene-styrene (ABS) moulding and extrusion materialsPart 2: Preparation of test specimens and determination of properties(ISO 2580-2 : 2003)English version of DIN EN ISO 2580-2Kunststoffe Acrylnitril-Butadien-Styrol (ABS)-Formmassen Teil 2: Herstellung von Prob

2、ekrpern undBestimmung von Eigenschaften (ISO 2580-2 : 2003)European Standard EN ISO 2580-2 : 2003 has the status of a DIN Standard.A comma is used as the decimal marker.National forewordThis standard has been published in accordance with a decision taken by CEN/TC 249 to adopt, withoutalteration, In

3、ternational Standard ISO 2580-2 as a European Standard.The responsible German body involved in its preparation was the Normenausschuss Kunststoffe (PlasticsStandards Committee), Technical Committee Polystyrol-Formmassen.The DIN Standards corresponding to the IEC Publications and International Standa

4、rds referred to in clause 3of the EN are as follows:IEC Publication/ DIN StandardISO StandardIEC 60093 DIN IEC 60093IEC 60112 DIN IEC 60112IEC 60243-1 DIN EN 60243-1IEC 60296 DIN VDE 0370-1ISO 62 DIN EN ISO 62ISO 75-2 DIN EN ISO 75-2ISO 178 DIN EN ISO 178ISO 179 DIN EN ISO 179ISO 180 DIN EN ISO 180I

5、SO 293 DIN 16770-1ISO 294-1 DIN EN ISO 294-1ISO 306 DIN EN ISO 306ISO 527-2 DIN EN ISO 527-2ISO 527-4 DIN EN ISO 527-4ISO 899-1 DIN EN ISO 899-1DEUTSCHE NORM May 2004DIN EN ISO 2580-2 No part of this standard may be reproduced without the prior permission ofDIN Deutsches Institut fr Normung e.V., Be

6、rlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).English price group 10www.din.dewww.beuth.de9570481Continued overleaf.Document comprises 12 pages.08.04G4G15G63G10G87G5Supersedes October 1999 edition.ISO 1133 DIN EN ISO 1133ISO 1183 DIN

7、 53479ISO 1656 DIN 53625ISO 2580-1 DIN EN ISO 2580-1ISO 2818 DIN EN ISO 2818ISO 3167 DIN EN ISO 3167ISO 4589 DIN EN ISO 4589-1 to DIN EN ISO 4589-3ISO 8256 DIN EN ISO 8256ISO 10350 DIN EN ISO 10350ISO 11357-2 DIN 53765AmendmentsThis standard differs from the October 1999 edition in that it has been

8、editorially revised and references havebeen updated.Previous editionsDIN 16772-2: 1977-08, 1988-12; DIN EN ISO 2580-2: 1999-10.National Annex NAStandards referred to(and not included in Normative references and Annex ZA)DIN 16770-1 Preparation of specimens of thermoplastic moulding materials by comp

9、ression mouldingDIN 53479 Determination of density of plastics and elastomersDIN 53625 Testing of rubber and elastomers Determination of total nitrogen content by the KjeldahlmethodDIN 53765 Thermal analysis of plastics and elastomers by the DSC methodDIN EN ISO 62 Plastics Determination of water ab

10、sorption (ISO 62 : 1999)DIN EN ISO 75-2 Determination of temperature of deflection of plastics under load Part 2: Plastics andebonite (ISO 75-2 : 1993)DIN EN ISO 178 Plastics Determination of flexural properties (ISO 178 : 1993)DIN EN ISO 179 Plastics Determination of Charpy impact properties (ISO 1

11、79 : 1993)DIN EN ISO 180 Plastics Determination of Izod impact strength (ISO 180 : 1993)DIN EN ISO 294-1 Plastics Injection moulding of test specimens of thermoplastic materials Part 1: Generalprinciples, and moulding of multipurpose and bar test specimens (ISO 294-1 : 1996)DIN EN ISO 306 Thermoplas

12、tic materials Determination of Vicat softening temperature (VST)(ISO 306 : 1994)DIN EN ISO 527-2 Plastics Determination of tensile properties Part 2: Test conditions for moulding andextrusion plastics (ISO 527-2 : 1993 + Corr 1 : 1994)DIN EN ISO 527-4 Plastics Determination of tensile properties Par

13、t 4: Test conditions for isotropic andorthtropic fibre-reinforced plastic composites (ISO 527-4 : 1997)DIN EN ISO 899-1 Plastics Determination of creep behaviour Part 1: Tensile creep (ISO 899-1 : 1993)DIN EN ISO 1133 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow r

14、ate(MVR) of thermoplastics (ISO 1133 : 1997)DIN EN ISO 2580-1 Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Part 1:Designation system and basis for specifications (ISO 2580-1 : 2000)DIN EN ISO 2818 Plastics Preparation of test specimens by machining (ISO 2818 : 1994)DIN EN I

15、SO 3167 Plastics Multi-purpose test specimens (ISO 3167 : 1993)DIN EN ISO 4589-1 Plastics Determination of burning behaviour by oxygen index Part 1: Guidance(ISO 4589-1 : 1996)DIN EN ISO 4589-2 Plastics Determination of burning behaviour by oxygen index Part 2: Ambient-temperature test (ISO 4589-2 :

16、 1996)DIN EN ISO 4589-3 Plastics Determination of burning behaviour by oxygen index Part 3: Elevated-temperature test (ISO 4589-3 : 1996)DIN EN ISO 8256 Plastics Determination of the tensile-impact strength of plastics (ISO 8256 : 1990,including Technical Corrigendum 1 : 1991)DIN EN ISO 10350 Plasti

17、cs Acquisition and presentation of comparable single-point data(ISO 10350-1 : 1993)Page 2DIN EN ISO 2580-2 : 2004-05English versionICS 83.080.20PlasticsAcrylonitrile-butadiene-styrene (ABS) moulding andextrusion materialsPart 2: Preparation of test specimens and determination of properties(ISO 2580-

18、2 : 2003) 2003. CEN All rights of exploitation in any form and by any meansreserved worldwide for CEN national members.Ref. No. EN ISO 2580-2 : 2003 EKunststoffe Acrylnitril-Butadien-Styrol (ABS)-Formmassen Teil 2:Herstellung von Probekrpern undBestimmung von Eigenschaften(ISO 2580-2 : 2003)This Eur

19、opean Standard was approved by CEN on 2003-11-10.CEN members are bound to comply with the CEN/CENELEC Internal Regulationswhich stipulate the conditions for giving this European Standard the status of anational standard without any alteration.Up-to-date lists and bibliographical references concernin

20、g such national stand-ards may be obtained on application to the Management Centre or to anyCEN member.The European Standards exist in three official versions (English, French, German).A version in any other language made by translation under the responsibility of aCEN member into its own language a

21、nd notified to the Management Centre hasthe same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, the CzechRepublic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland,Ireland, Italy, Luxembourg, Malta, the Netherlands, Norway, Portugal, Slo

22、vakia,Spain, Sweden, Switzerland, and the United Kingdom.EN ISO 2580-2December 2003Management Centre: rue de Stassart 36, B-1050 BrusselsEuropean Committee for StandardizationComit Europen de NormalisationEuropisches Komitee fr NormungPlastiques Acrylonitrile-butadine-styrne (ABS) pour moulage et ex

23、tru-sion Partie 2: Prparation des prou-vettes et dtermination des proprits(ISO 2580-2 : 2003)Supersedes EN ISO 2580-2 : 1999.Page 2EN ISO 2580-2 : 2003ForewordInternational StandardISO 2580-2 : 2003 Plastics Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Part 2:Preparation of

24、 test specimens and determination of properties,which was prepared by ISO/TC 61 Plastics of the International Organization for Standardization, has beenadopted by Technical Committee CEN/TC 249 Plastics, the Secretariat of which is held by IBN, as a EuropeanStandard.This European Standard shall be g

25、iven the status of a national standard, either by publication of an identical textor by endorsement, and conflicting national standards withdrawn, by June 2004 at the latest.In accordance with the CEN/CENELEC Internal Regulations, the national standards organizations of thefollowing countries are bo

26、und to implement this European Standard:Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,Italy, Luxembourg, Malta, the Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland, and theUnited Kingdom.Endorsement noticeThe text of th

27、e International Standard ISO 2580-2 : 2003 was approved by CEN as a European Standard withoutany modification.NOTE: Normative references to international publications are listed in Annex ZA (normative).Page 3EN ISO 2580-2 : 200323335669Page 4EN ISO 2580-2 : 2003Page 5EN ISO 2580-2 : 2003Page 6EN ISO 2580-2 : 2003Page 7EN ISO 2580-2 : 2003Page 8EN ISO 2580-2 : 2003Page 9EN ISO 2580-2 : 2003Page 10EN ISO 2580-2 : 2003