DIN EN 16291-2-2013 Glass packaging - Screw finishes for pressure capsules - Part 2 One way glass MCA 2 finish German version EN 16291-2 2013《玻璃包装 压力传感器的螺纹瓶口 第2部分 单向玻璃MCA 2瓶口 德文版本E.pdf

《DIN EN 16291-2-2013 Glass packaging - Screw finishes for pressure capsules - Part 2 One way glass MCA 2 finish German version EN 16291-2 2013《玻璃包装 压力传感器的螺纹瓶口 第2部分 单向玻璃MCA 2瓶口 德文版本E.pdf》由会员分享，可在线阅读，更多相关《DIN EN 16291-2-2013 Glass packaging - Screw finishes for pressure capsules - Part 2 One way glass MCA 2 finish German version EN 16291-2 2013《玻璃包装 压力传感器的螺纹瓶口 第2部分 单向玻璃MCA 2瓶口 德文版本E.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、May 2013 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 55.

2、100!%$*d“2010765www.din.deDDIN EN 16291-2Glass packaging Screw finishes for pressure capsules Part 2: One way glass MCA 2 finish;English version EN 16291-2:2013,English translation of DIN EN 16291-2:2013-05Verpackungen aus Glas Schraubmundstcke fr Flaschen mit Innendruck Teil 2: Einweg-MCA 2-Mundstc

3、k;Englische Fassung EN 16291-2:2013,Englische bersetzung von DIN EN 16291-2:2013-05Emballage en verre Bagues vis pour capsules pression Partie 2: Bague MCA 2 pour verre perdu;Version anglaise EN 16291-2:2013,Traduction anglaise de DIN EN 16291-2:2013-05www.beuth.deDocument comprises 12 pagesIn case

4、of doubt, the German-language original shall be considered authoritative.01.17DIN EN 16291-2:2013-05 2 A comma is used as the decimal marker. Based on EN 16291-2:2013/AC:2014, the English version of DIN EN 16291-2:2013-05 has been correctedas follows: Figure 1 has been replaced. National foreword Th

5、is document (EN 16291:2013) has been prepared by Technical Committee CEN/TC 261 “Packaging” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Verpackungswesen (Packaging Standards Committee), Working Committee NA 115-02-04 AA Behltnisse aus

6、 Glas. In addition to the legal units of measurement, this standard also uses the unit “in” (inch). It should, however, be noted that the Gesetz ber Einheiten im Messwesen (German Law on units in metrology) prohibits the use of this unit for official and commercial purposes in Germany. EUROPEAN STAN

7、DARD NORME EUROPENNE EUROPISCHE NORM EN 16291-2 March 2013 ICS 55.100 English Version Glass packaging - Screw finishes for pressure capsules - Part 2: One way glass MCA 2 finish Emballage en verre - Bagues vis pour capsules pression - Partie 2: Bague MCA 2 pour verre perdu Verpackungen aus Glas - Sc

8、hraubmundstcke fr Flaschen mit Innendruck - Teil 2: Einweg-MCA 2-Mundstck This European Standard was approved by CEN on 12 January 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national

9、 standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version

10、 in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czec

11、h Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EU

12、ROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16291-2:2013: EEN 16291-2:

13、2013 (E) 2 Contents Page Foreword . 3 Introduction 4 1 Scope 5 2 Terms and definitions 5 3 Dimensions. 5 Bibliography 10 DIN EN 16291-2:2013-05 EN 16291-2:2013 (E) 3 Foreword This document (EN 16291-2:2013) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is

14、held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by September 2013. Attention is drawn to the poss

15、ibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. EN 16291, Glass packaging Screw finishes for pressure capsules, consists of the following parts: Part 1: Returnable

16、glass MCA 2 finish; Part 2: One way glass MCA 2 finish. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Fin

17、land, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 16291-2:2013-05 EN 16291

18、-2:2013 (E) 4 Introduction This document is based on CE.T.I.E. (International Technical Centre for Bottling and related Packaging) data sheet GME 320 1. Efficient packaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to da

19、mage or wastage of the contents of the pack. DIN EN 16291-2:2013-05 EN 16291-2:2013 (E) 5 1 Scope This European Standard specifies the dimensions of the screw finish for glass containers designated MCA 2 for one way glass. 2 Terms and definitions For the purposes of this document, the following term

20、 and definition applies. 2.1 MCA (glass) finish designed for the closure of pressurised or vacuum liquids with a tamper-evident closure (metal or plastic) 3 Dimensions The design and dimensions of the finish shall be as shown in Table 1 and Figures 1, 2, 3, 4 and 5. Table 1 Design and dimensions of

21、the finish Pitch TPI cutter 3,175 mm 2 12 8 12,5 mm = Helix angle or angle or fixture to cutter NOTE TPI = threads per inch. One inch is equal to 25,4 mm. The Tan of helix angle for cutter is calculated via the following formula: pitch Tan = (nominal T + nominal E) 2 where T is the thread diameter;

22、E is the wall diameter of threaded finish. The average of the maximum and minimum of “L“ diameter is as close as possible to “L“ nominal. The mean diameter 2min diameter max diameter + Lis in the tolerance of 0,2 mm. Optional: depressed thread at mould parting line (see EN 16292). DIN EN 16291-2:201

23、3-05 EN 16291-2:2013 (E) 6 Dimensions in millimetres Key N neck (under bead) diameter H thread height S start of thread position from sealing surface to intersection of thread flank F height of the finish L locking bead diameter T thread diameter E wall diameter of threaded finish NOTE Bore diameter

24、: 18,1 mm 1,0 mm for a depth of 3mm. Figure 1 MCA 2 finish DIN EN 16291-2:2013-05 EN 16291-2:2013 (E) 7 Dimensions in millimetres Key a mould parting line b sealing surface The sealing surface is smooth and free of any defects and flash. Figure 2 Possible alternative constructions of the bore entran

25、ce to suit glass manufacturer DIN EN 16291-2:2013-05 EN 16291-2:2013 (E) 8 Dimensions in millimetres Minimum through bore 16,0 Figure 3 Detail of the profile DIN EN 16291-2:2013-05 EN 16291-2:2013 (E) 9 NOTE Z-Z is the last full depth and width of thread. Beyond this point and Y-Y, the thread root i

26、s increased gradually to full thread diameter T in 90. Figure 4 Run out of thread Dimensions in millimetres Figure 5 Limit of construction DIN EN 16291-2:2013-05 EN 16291-2:2013 (E) 10 Bibliography 1 CE.T.I.E. data sheet GME 320 - Pilferproof for pressured beverages1)2 EN 16292, Glass packaging Screw finishes Depressed threads 1) Obtainable through Centre Technique International de lEmbouteillage et du Conditionnement (CE.T.I.E), 112- 114, rue La Botie, 75008 Paris, France; www.cetie.org, TP: 0033-1-42 65 26 45, TF: 0033-1-40 07 03 21. DIN EN 16291-2:2013-05