BS ISO 22960-2008 Titanium and titanium alloys - Determination of iron - Molecular absorption spectrometry using 1 10- phenanthroline《钛和钛合金 铁的测定 使用1 10邻二氮杂菲的分子吸收光谱测定法》.pdf

《BS ISO 22960-2008 Titanium and titanium alloys - Determination of iron - Molecular absorption spectrometry using 1 10- phenanthroline《钛和钛合金 铁的测定 使用1 10邻二氮杂菲的分子吸收光谱测定法》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 22960-2008 Titanium and titanium alloys - Determination of iron - Molecular absorption spectrometry using 1 10- phenanthroline《钛和钛合金 铁的测定 使用1 10邻二氮杂菲的分子吸收光谱测定法》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS ISO 22960:2008Titanium and titanium alloys Determination of iron Molecular absorption spectrometry using 1, 10-phenanthrolineICS 77.120.50g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55

2、g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS ISO 22960:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 May 2008 BSI 2008ISBN 978 0 580 57633 1National forewordThis British Standard is the UK implementation of ISO 22960:2

3、008.The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a cont

4、ract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publicationDate CommentsReference numberISO 22960:2008(E)INTERNATIONAL STANDARD ISO22960First edition2008-01-15Titanium and tit

5、anium alloys Determination of iron Molecular absorption spectrometry using 1, 10-phenanthroline Titane et alliages de titane Dosage du fer Spectromtrie dabsorption molculaire par la 1,10-phnanthroline BS ISO 22960:2008ii iiiContents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Principle

6、. 1 4 Reagents 1 5 Apparatus 2 6 Sample . 3 7 Procedure 3 8 Expression of results . 4 9 Precision 5 BS ISO 22960:2008iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International St

7、andards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also

8、 take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committee

9、s is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possib

10、ility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 22960 was prepared by Technical Committee ISO/TC 79, Light metals and their alloys, Subcommittee SC 11, Titanium. BS ISO 22960:20

11、081Titanium and titanium alloys Determination of iron Molecular absorption spectrometry using 1, 10-phenanthroline 1 Scope This International Standard specifies a molecular absorption spectrometric method using 1, 10-phenanthroline for the determination of the mass fraction of iron in titanium and t

12、itanium alloys. The method is applicable to titanium and titanium alloys with a mass fraction of iron in the range from 0,005 % to 2,0 %. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited app

13、lies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 384:1978, Laboratory glassware Principles of design and construction of volumetric glassware ISO 648:1), Laboratory glassware Single volume pipettes ISO 1042:1998, Laboratory glassware

14、 One-mark volumetric flasks ISO 3696:1987, Water for analytical laboratory use Specifications and test methods ISO 4787:1984, Laboratory glassware Volumetric glassware Methods for use and testing of capacity 3 Principle Dissolve the test portion in hydrochloric acid and hydrofluoric acid. Add nitric

15、 acid to oxidize titanium. Then add boric acid, tartaric acid, ammonium acetate and hydroxyl ammonium chloride. Add 1, 10-phenanthroline to make a 1,10-phenanthroline-iron complex. Determine the iron concentration in the test portion using a spectrophotometer. 4 Reagents 4.1 General During the analy

16、sis, use only reagents of recognized analytical grade and water that complies with grade 2 of ISO 3696. 1) To be published. (Revision of ISO 648:1977) BS ISO 22960:20082 4.2 Hydrochloric acid (1+1) Add slowly 500 ml of hydrochloric acid ( 201,16 g/ml to 1,19 g/ml) to 500 ml of water. 4.3 Nitric acid

17、 (1+1) Add slowly 500 ml of nitric acid ( 201,42 g/ml) to 500 ml of water. 4.4 Hydrofluoric acid (1+1) Add, carefully and slowly, 100 ml of hydrofluoric acid ( 201,14 g/ml) to 100 ml of water. 4.5 Boric acid 4.6 Tartaric acid solution (200 g/l) 4.7 Ammonium acetate solution (500 g/l) 4.8 Hydroxyl am

18、monium chloride solution (100 g/l) 4.9 1, 10-phenanthroline solution (100 g/l) Dissolve 2,4 g of 1,10-phenanthrolinium chloride monohydrate in 1 000 ml of water, or dissolve 2,0 g of 1,10-phenanthroline monohydrate in 100 ml of ethanol minimum purity 95 % (volume fraction) and dilute to 1 000 ml wit

19、h water. 4.10 Iron standard solution 4.10.1 Iron standard stock solution (0,500 mg Fe/ml) Weigh, to the nearest 0,1 mg, 0,500 g of iron metal minimum purity 99,9 % (mass fraction) into a 300 ml beaker, heat and decompose with 30 ml of hydrochloric acid (4.2). Add 5 ml of nitric acid (4.3) to oxidize

20、 iron and heat to evaporate nitrogen oxides. After cooling, transfer to a 1 000 ml volumetric flask, make up to the mark with water and mix. 4.10.2 Iron standard solution (0,050 mg Fe/ml) Pipette 10,00 ml of iron standard stock solution (4.10.1) to a 100 ml volumetric flask, make up to the mark with

21、 water and mix. Prepare this solution on the day of use. 5 Apparatus 5.1 General. Use normal laboratory apparatus. 5.2 Volumetric glassware, of class A complying with ISO 384, ISO 648 and ISO 1042. Use in accordance with ISO 4787. 5.3 Analytical balance, sensitive to 0,1 mg. 5.4 Spectrophotometer. B

22、S ISO 22960:200836 Sample 6.1 Sampling The sampling procedure for titanium and titanium alloys shall be agreed upon until a corresponding standard method has been published. 6.2 Test portion Extract a test portion from the test sample as specified in Table 1 and weigh to the nearest 0,1 mg. Table 1

23、Recommended test portion masses and aliquot volume taken in 7.4 Mass fraction of iron Mass of test portion Volume of aliquot taken in 7.4 c) % g ml W 0,005 0,1 1,0 20,0 W 0,1 0,4 1,0 10,0 W 0,4 0,8 0,50 10,0 W 0,8 u 2,0 0,20 10,0 7 Procedure 7.1 Number of determinations Carry out the determination a

24、t least in duplicate, as far as possible under repeatability conditions, on each sample. 7.2 Blank test Carry out a blank test in parallel with the analysis, using the same quantities of all reagents but omitting the test portion. 7.3 Preparation of working curve Pipette 0 ml, 2 ml, 4 ml, 6 ml and 8

25、 ml of iron standard solution (4.10.2) into five 100 ml volumetric flasks. Add 15 ml of tartaric acid solution (4.6), 25 ml of ammonium acetate solution (4.7) and 5 ml of hydroxyl ammonium chloride solution (4.8) to each volumetric flask. Dilute to about 80 ml with water and mix. Add 10 ml of 1,10-p

26、henanthroline solution (4.9) to each volumetric flask, make up to the mark with water and mix. After allowing to stand for about 20 min at room temperature, transfer a part of the solution into an absorption cell (10 mm), and measure the absorbance at a wavelength of 510 nm using water as a contrast

27、 solution. Prepare the curve showing the relation between the obtained absorbance and the iron concentration, in milligrams per 100 ml. Ensure that the graph achieves better than 0,999 correlation and is suitably linear. Prepare the working curve for a sample by parallel shifting of the relation cur

28、ve so as to let the curve pass the origin of the coordinate axes. BS ISO 22960:20084 7.4 Preparation of test solution for presentation to spectrophotometer Carry out the following steps. a) Transfer the test portion to a polyethylene beaker (200 ml). b) Add 10 ml of hydrochloric acid (4.2) and 5 ml

29、of hydrofluoric acid (4.4), cover with a polyethylene watch glass and heat gently on a water bath to decompose the test portion. Add 3 ml of nitric acid (4.3) and continue heating until nitrogen oxides evaporate. Then add 3 g of boric acid (4.5), stir to dissolve the boric acid and cool to room temp

30、erature. c) Transfer the solution into a 100 ml volumetric flask and make up to the mark with water. Pipette a test solution into two volumetric flasks (A and B) (specified volume in Table 1) according to the mass fractions of iron in the sample. d) Add 15 ml of tartaric acid solution (4.6), 25 ml o

31、f ammonium acetate solution (4.7) and 5 ml of hydroxyl ammonium chloride solution (4.8) to the volumetric flasks A and B. Dilute to about 80 ml with water and mix. e) Add 10 ml of 1,10-phenanthroline solution (4.9) to volumetric flask A, and make up to the mark with water. To the volumetric flask B,

32、 add water to make up to the mark and mix. 7.5 Determination of iron concentration After allowing to stand for about 20 min at room temperature, transfer a part of the solution into an absorption cell (10 mm), and measure the absorbance at a wavelength of 510 nm using the solution in flask B as the

33、contrast solution. Determine the iron concentration of the test solution from the working curve (7.3). 8 Expression of results The mass fraction of iron in the test portion, wFe, expressed as a percentage, is given by the following equation: wV=312Fe100 10m100(1) where 1is the concentration of iron

34、in the aliquot solution, expressed in mg/100 ml; 2is the concentration of iron in the blank solution, expressed in mg/100 ml; V is the volume of aliquot solution, expressed in ml; m is the mass of test portion, expressed in g. Calculate the mass fraction of iron in the test portion to the third deci

35、mal place. The difference in results of two parallel determinations of the mass fraction of iron in the same sample shall not be greater than the tolerance Equation (2), (3), or (4). If the difference exceeds the tolerance, the analysis shall be repeated. BS ISO 22960:200859 Precision The tolerance

36、of this analytical method is expressed by the following equations: Repeatability limit 2,8 0,005 5 (WFe) + 0,001 0 % (mass fraction) (2) Within-laboratory-reproducibility limit 2,8 0,008 3 (WFe) + 0,001 0 % (mass fraction) (3) Between-laboratory-reproducibility limit 2,8 0,023 3 (WFe) + 0,000 8 % (m

37、ass fraction) (4) BS ISO 22960:2008BS ISO 22960:2008BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporate

38、d by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone findin

39、g an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called

40、PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards a

41、re also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of inform

42、ation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax:

43、+44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 89

44、96 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyrigh

45、t, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise

46、without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.