BS ISO 1832-2017 Indexable inserts for cutting tools Designation《切削刀具用可转位刀片 名称》.pdf

《BS ISO 1832-2017 Indexable inserts for cutting tools Designation《切削刀具用可转位刀片 名称》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 1832-2017 Indexable inserts for cutting tools Designation《切削刀具用可转位刀片 名称》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 1832:2017Indexable inserts for cuttingtools DesignationBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 1832:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 1832:2017. It supersedes BS ISO 1832:2012 which is wi

2、thdrawn.The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessar

3、y provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 92410 1 ICS 25.100.01 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was

4、 published under the authority of the Standards Policy and Strategy Committee on 31 March 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 1832:2017 ISO 2017Indexable inserts for cutting tools DesignationPlaquettes amovibles pour outils coupants DsignationINTERNA

5、TIONAL STANDARDISO1832Sixth edition2017-02Reference numberISO 1832:2017(E)BS ISO 1832:2017ISO 1832:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or ut

6、ilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyri

7、ght officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 1832:2017ISO 1832:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Explanation of designation code 15 Symbols 35.1 Symbo

8、l for insert shape Reference 35.2 Symbol for normal clearance Reference 45.3 Symbol for tolerance class Reference 45.4 Symbol for fixing and/or chip breakers Reference 75.5 Symbol for insert size Reference . 95.6 Symbol for insert thickness Reference . 95.7 Symbol for insert corner configuration Ref

9、erence 106 Optional symbols for indexable inserts 126.1 General 126.2 Symbol for cutting edge condition Reference 126.3 Symbol for the corner type and the application of the insert (direction of feed motion) Reference . 137 Additional symbols for tipped inserts 137.1 General 137.2 Size of cutting ed

10、ge condition Reference .137.2.1 General. 137.2.2 E = rounded . 137.2.3 T = chamfered 147.2.4 S = chamfered and rounded 147.2.5 K = double chamfered .157.2.6 P = double chamfered and rounded . 167.3 Style of tipped or solid cutting edge and number of tipped corners Reference 167.4 Length of tipped cu

11、tting edge Reference .18Annex A (informative) Symbols for insert size (reference ) according to standardized inscribed circles for equilateral and round inserts 20Annex B (informative) Symbols for standardized insert thicknesses (reference ) 22Annex C (informative) Relationship between designations

12、in this document and the ISO 13399 series 23Bibliography .24 ISO 2017 All rights reserved iiiContents PageBS ISO 1832:2017ISO 1832:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing

13、 International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liais

14、on with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Direc

15、tives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that

16、some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent decl

17、arations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformit

18、y assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.Attention is drawn to the possibility that some of the elements of this document may be the su

19、bject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.This document was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This sixth edition cancels and replaces the fifth editi

20、on (ISO 1832:2012), which has been technically revised.iv ISO 2017 All rights reservedBS ISO 1832:2017INTERNATIONAL STANDARD ISO 1832:2017(E)Indexable inserts for cutting tools Designation1 ScopeThis document establishes a code for the designation of the usual types of indexable inserts for cutting

21、tools in hard cutting materials or any other cutting materials, in order to simplify orders and specifications for such inserts.It also specifies the designations for cubic boron nitride (BL, BH, BC) inserts, tipped and solid, as well as polycrystalline diamond (DP) inserts, tipped.2 Normative refer

22、encesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) a

23、pplies.ISO 513, Classification and application of hard cutting materials for metal removal with defined cutting edges Designation of the main groups and groups of applicationISO 3002-1, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, refer

24、ence systems, tool and working angles, chip breakersISO 16462, Cubic boron nitride inserts, tipped or solid Dimensions, typesISO 16463, Polycristalline diamond inserts, tipped Dimensions, types3 Terms and definitionsNo terms and definitions are listed in this document.ISO and IEC maintain terminolog

25、ical databases for use in standardization at the following addresses: IEC Electropedia: available at http:/ www .electropedia .org/ ISO Online browsing platform: available at http:/ www .iso .org/ obp4 Explanation of designation codeFor indexable inserts, the designation code comprises nine symbols

26、for designating the dimensions and other characteristics; the first seven symbols (symbols to ) shall be used in every designation. Symbols and may be used when necessary.For tipped inserts in accordance with ISO 16462 and ISO 16463, the designation code comprises 12 symbols for designating the dime

27、nsions and other characteristics; symbols to as well as and shall be used in every designation. Symbols , and may be used when necessary. Symbols and shall be separated by a dash as shown in Clause 4, example 2.In addition to the standardized designation for indexable inserts and tipped inserts, a s

28、upplementary symbol consisting of one or two characters may be added by the manufacturer for a better description of his/her product (for example, different chip breakers), provided this symbol is separated from the standardized designation by a dash and that it does not contain letters specific to

29、references , and . ISO 2017 All rights reserved 1BS ISO 1832:2017ISO 1832:2017(E)No addition to or extension of the designations specified in this document shall be made without consultation with ISO/TC 29 and without its agreement. Rather than adding symbols not provided for in this system, it is p

30、referable to add all necessary explanations in the form of detailed sketches or specifications to the designation in accordance with this document.However, if the letter symbol “X” is used in position 4 of the designation, it is allowed to use, in positions 5, 6 and 7, symbols representing values no

31、t appearing in this document, but which shall be described explicitly using the sketch or the detailed specifications given in 5.4.The significance of the symbols constituting the designation code is as follows: Letter symbol identifying insert shape (see 5.1)Compulsory symbols for indexable inserts

32、Compulsory symbols for tipped inserts according to ISO 16462 and ISO 16463, except as noted Letter symbol identifying normal clearance (see 5.2) Letter symbol identifying tolerance class (see 5.3) Letter symbol indicating fixing and/or chip breakers (see 5.4) Number symbol identifying insert size (s

33、ee 5.5) Number symbol identifying insert thickness (see 5.6) Letter or number symbol identifyinginsert corner configu-ration (see 5.7) Letter symbol indicating (optional symbol for indexable and tipped inserts)cutting edge condition (see 6.2) Letter symbol identifying (optional symbol for indexable

34、and tipped inserts)cutting direction (see 6.3) Number symbol identifying (optional symbol for tipped inserts)size of cutting edge condition (see 7.2) Letter symbol identifying style of tipped or solid cutting edge and num-ber of tipped corners (see 7.3) Letter or number symbol identifyinglength of t

35、ipped cut-ting edge (see 7.4) Manufacturers symbol or cutting material designation according to ISO 513 (optional symbol for indexable and tipped inserts)2 ISO 2017 All rights reservedBS ISO 1832:2017ISO 1832:2017(E)EXAMPLE 1 General designation Metric dimensions: T P G N 16 03 08 E N Inch dimension

36、s: T P G N 3 2 2 E N EXAMPLE 2 Designation of inserts according to ISO 16462 and ISO 16463 Designation of insert for turningS N M A 15 06 08 E (N) B L .Designation of insert for millingT P G T 16 T3 AP S 01520 R M 028 .The designations and symbols of the different angles allowing geometrical definit

37、ion of the indexable inserts shall conform with ISO 3002-1, with the following conventions: the insert is considered in the tool-in-hand system; the reference plane, Pr, is parallel to the base of the insert; the assumed working plane, Pf, is perpendicular to the reference plane, Pr, and is parallel

38、 to the assumed direction of feed motion. This plane is defined only in the case of inserts having one or more wiper edges.The assumed direction of feed motion is taken parallel to the considered wiper edge (see Note 1 to Table 9).For the relationship between designations in this document and the IS

39、O 13399 series, see Annex C.5 Symbols5.1 Symbol for insert shape Reference See Table 1.Table 1TypeLetter symbolDescription of shapeIncluded angle, rIllustrationIEquilateral and equian-gular insertsH Hexagonal inserts 120O Octagonal inserts 135P Pentagonal inserts 108S Square inserts 90T Triangular i

40、nserts 60aThe smaller angle is always the included angle that is considered. ISO 2017 All rights reserved 3BS ISO 1832:2017ISO 1832:2017(E)TypeLetter symbolDescription of shapeIncluded angle, rIllustrationIIEquilateral but non- equiangular insertsCRhombic inserts80aD 55aE 75aM 86aV 35aW Trigon inser

41、ts 80aIIINon-equilateral but equiangular insertsL Rectangular inserts 90IVNon-equilateral and non-equiangular insertsAParallelogram-shaped inserts85aB 82aK 55aV Round inserts R Round inserts aThe smaller angle is always the included angle that is considered.5.2 Symbol for normal clearance Reference

42、See Table 2.Table 2Letter symbolFor normal clearance, choose, from the letter symbols listed below, the one that corresponds to the major cut-ting edge (see the figure below).If (in spite of different clearances) all cutting edges have to be used as major cutting edges, the symbol to be used for the

43、 designation of the normal clearance shall be the symbol applicable to the normal clearance of the longer cutting edge, which is also considered the major cutting edge for the indication of the insert size (see reference ).A 3B 5C 7D 15E 20F 25G 30N 0P 11O Other normal clearances requiring special s

44、peci -fication5.3 Symbol for tolerance class Reference See Table 3.The dimensions concerned are d (nominal diameter of the inscribed circle of the insert), s (thickness of the insert) and m. For this last dimension, the three cases represented in Figures 1 to 3 are distinguished.Table 1 (continued)4

45、 ISO 2017 All rights reservedBS ISO 1832:2017ISO 1832:2017(E)Figure 1 Case 1: inserts with odd numbers of sides and rounded cornersFigure 2 Case 2: inserts with even numbers of sides and rounded cornersFigure 3 Case 3: inserts with wiper edges (see Note 1 in Table 9)Table 3LetterTolerance in millime

46、tres Tolerance in inchesd m s d m sAa0,025 0,005 0,025 0,001 0,000 2 0,001Fa0,013 0,005 0,025 0,000 5 0,000 2 0,001Ca0,025 0,013 0,025 0,001 0,000 5 0,001H 0,013 0,013 0,025 0,000 5 0,000 5 0,001E 0,025 0,025 0,025 0,001 0,001 0,001G 0,025 0,025 0,13 0,001 0,001 0,005Jafrom 0,05bto 0,15b0,005 0,025f

47、rom 0,002bto 0,006b0,000 2 0,001Kafrom 0,05bto 0,15b0,013 0,025from 0,002bto 0,006b0,000 5 0,001Lafrom 0,05bto 0,15b0,025 0,025from 0,002bto 0,006b0,001 0,001Mfrom 0,05bto 0,15bfrom 0,08bto 0,2b0,13from 0,002bto 0,006bfrom 0,003bto 0,008b0,005Nfrom 0,05bto 0,15bfrom 0,08bto 0,2b0,025from 0,002bto 0,

48、006bfrom 0,003bto 0,008b0,001Ufrom 0,08bto 0,25bfrom 0,13bto 0,38b0,13from 0,003bto 0,01bfrom 0,005bto 0,015b0,005a These tolerance classes normally apply to indexable inserts with wiper edges.b The tolerance is dependent upon the insert size (see Tables 4 and 5) and should be indicated for insert according to the corresponding dimensional standards. ISO 2017 All rights reserved 5BS ISO 18