BS ISO 16525-4-2014 Adhesives Test methods for isotropic electrically conductive adhesives Determination of shear strength and electrical resistance using rigid-to-rigid bonded ass.pdf
《BS ISO 16525-4-2014 Adhesives Test methods for isotropic electrically conductive adhesives Determination of shear strength and electrical resistance using rigid-to-rigid bonded ass.pdf》由会员分享,可在线阅读,更多相关《BS ISO 16525-4-2014 Adhesives Test methods for isotropic electrically conductive adhesives Determination of shear strength and electrical resistance using rigid-to-rigid bonded ass.pdf(18页珍藏版)》请在麦多课文档分享上搜索。
1、BSI Standards PublicationBS ISO 16525-4:2014Adhesives Test methods for isotropic electrically conductive adhesivesPart 4: Determination of shear strength and electrical resistance using rigid-to-rigid bonded assembliesBS ISO 16525-4:2014 BRITISH STANDARDNational forewordThis British Standard is the
2、UK implementation of ISO 16525-4:2014. The UK participation in its preparation was entrusted to TechnicalCommittee PRI/52, Adhesives.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provis
3、ions of a contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 76956 6 ICS 83.180Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published u
4、nder the authority of the Standards Policy and Strategy Committee on 31 May 2014.Amendments issued since publicationDate Text affectedBS ISO 16525-4:2014 ISO 2014Adhesives Test methods for isotropic electrically conductive adhesives Part 4: Determination of shear strength and electrical resistance u
5、sing rigid-to-rigid bonded assembliesAdhsifs Mthodes dessai pour adhsifs conductivit lectrique isotrope Partie 4: Dtermination de la rsistance au cisaillement et de la rsistance lectrique des assemblages colls rigide sur rigideINTERNATIONAL STANDARDISO16525-4First edition2014-05-15Reference numberIS
6、O 16525-4:2014(E)BS ISO 16525-4:2014ISO 16525-4:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, inclu
7、ding photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22
8、749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 16525-4:2014ISO 16525-4:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Apparatus and materials 25 Specimen . 26 Tests . 36.1 Atmospheric cond
9、itions 36.2 Procedure 37 Test report . 4Annex A (normative) Apparatus for shear strength tests 5Annex B (normative) Procedure of shear strength tests . 7Bibliography 9BS ISO 16525-4:2014ISO 16525-4:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of n
10、ational standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Inter
11、national organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those inte
12、nded for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso
13、.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be
14、 in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 61, Plastics, Subcommitt
15、ee SC 11, Products.ISO 16525 consists of the following parts, under the general title Adhesives Test methods for isotropic electrically conductve adhesives: Part 1: General test methods Part 2: Determination of electric characteristics for use in electronic assemblies Part 3: Determination of heat-t
16、ransfer properties Part 4: Determination of shear strength and electrical resistance using rigid-to-rigid bonded assemblies Part 5: Determination of shear fatigue Part 6: Determination of pendulum-type shear impact Part 7: Environmental test methods Part 8: Electrochemical migration test methods Par
17、t 9: Determination of high-speed signal-transmission characteristicsiv ISO 2014 All rights reservedBS ISO 16525-4:2014INTERNATIONAL STANDARD ISO 16525-4:2014(E)Adhesives Test methods for isotropic electrically conductive adhesives Part 4: Determination of shear strength and electrical resistance usi
18、ng rigid-to-rigid bonded assembliesSAFETY STATEMENT Persons using this part of ISO 16525 should be familiar with normal laboratory practice. This part of ISO 16525 does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establi
19、sh appropriate safety and health practices and to ensure compliance with any regulatory conditions.IMPORTANT Certain procedures specified in this part of ISO 16525 might involve the use or generation of substances, or the generation of waste, that could constitute a local environmental hazard. Refer
20、ence should be made to appropriate documentation on safe handling and disposal after use.1 ScopeThis part of ISO 16525 specifies test methods using miniature specimens to determine shear strength and electrical resistance of a bonded joint that consists of isotropic electrically conductive adhesives
21、 and rigid adherends in specified conditions.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of
22、the referenced document (including any amendments) applies.ISO 291, Plastics Standard atmospheres for conditioning and testingISO 431, Copper refinery shapesISO 472, Plastics VocabularyISO 10365, Adhesives Designation of main failure patternsISO 17212, Structural adhesives Guidelines for the surface
23、 preparation of metals and plastics prior to adhesive bonding3 Terms and definitionsFor the purposes of this document, the terms and definitions in ISO 472 and the following apply.3.1displacement ratecrosshead speed of the test machine, i.e. a jig, which applies the load to the isotropic electricall
24、y conductive adhesive layer during the shear strength test ISO 2014 All rights reserved 1BS ISO 16525-4:2014ISO 16525-4:2014(E)4 Apparatus and materials4.1 Apparatus for shear fatigue tests, consisting of a tensile machine, a specimen-holder jig, an ohmmeter, and a recorder. The specifications shall
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO1652542014ADHESIVESTESTMETHODSFORISOTROPICELECTRICALLYCONDUCTIVEADHESIVESDETERMINATIONOFSHEARSTRENGTHANDELECTRICALRESISTANCEUSINGRIGIDTORIGIDBONDEDASSPDF

链接地址:http://www.mydoc123.com/p-585067.html