BS ISO 15637-1-2002 Holding fixtures of cylindrical abrasive sleeves - Holding fixtures with shank for hand-held grinding machines《圆柱形研磨套筒支承夹具 手动砂轮机用带柄的支承夹具》.pdf

《BS ISO 15637-1-2002 Holding fixtures of cylindrical abrasive sleeves - Holding fixtures with shank for hand-held grinding machines《圆柱形研磨套筒支承夹具 手动砂轮机用带柄的支承夹具》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 15637-1-2002 Holding fixtures of cylindrical abrasive sleeves - Holding fixtures with shank for hand-held grinding machines《圆柱形研磨套筒支承夹具 手动砂轮机用带柄的支承夹具》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 15637-1:2002 Holding fixtures of cylindrical abrasive sleeves Part 1: Holding fixtures with shank for hand-held grinding machines ICS 25.100.70 BS ISO 15637-1:2002 This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Co

2、mmittee, was published under the authority of the Standards Policy and Strategy Committee on 13 December 2002 BSI 13 December 2002 ISBN 0 580 40945 7 National foreword This British Standard reproduces verbatim ISO 15637-1:2002 and implements it as the UK national standard. The UK participation in it

3、s preparation was entrusted to Technical Committee MTE/13, Grinding wheels, abrasive tools, paper cloths and powders, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which imple

4、ment international publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purpor

5、t to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee

6、any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii

7、, a blank page, pages 1 to 3 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsINTERNATIONAL STANDARD ISO 15637-1 First edition 2002-11-15 Reference number ISO 15637-1:2002(E) Hol

8、ding fixtures of cylindrical abrasive sleeves Part 1: Holding fixtures with shank for hand-held grinding machines Porte-manchons pour manchons abrasifs cylindriques Partie 1: Porte-manchons queue pour meuleuses portativesBSISO156371:2002 ISO -73651:1)E(2002 ii FDP dicslaimre This FDP fam elitnoc yt

9、deddebme niayfep.seca In roccatiw ecnadA hycilop gnisnecil sebod, thf sim eliarp eb ytnieiv ro dewb detu sllah ton eb tidesselnu de tt ehyfepseca hwich rae meil era deddebct desnetsni dna olat no delmoc ehtupre epfrromign tide ehti.gn In odaolnwt gnidihs file, rapticca setpe trehiet neh serilibisnop

10、ty fo ton fnirisebodA gnign ilop gnisnecilcy. TI ehSO tneCrceS larteraita catpecon s illibaity it nihs aera. ebodA si t armedarak fo dAS ebotsysme Inroctarop.de teDailfo s tfos ehtware prtcudos t desuo crtaet ehFDP si ff eb nac elit ni dnuoG ehlarene Info talerive to tf eh;eli teh PDF-rctaerap noima

11、teers weer tpof dezimior rptnii.gn vErec yaeeb sah ert nakt neo rusnet etah tf ehi elis tiusbaf elob esu ry ISO merebm seidob. In the kilnuley evtne ttah a borpmel talerign to ti f si,dnuo saelpfni erom teh tneCS larterceratai ta thserdda es igvne olebw. ISO 2002 Ar llieser sthgrvsselnU .de torehcep

12、s esiwfi,dei rap ont iht fos bupliactim noarper eb yro decudo tuzilina ni dey from b roy nasnaem y, tcelernahcem ro cinoicla, inclidung tohppocoying m dnaicrfomli, tiwtuoh permini noiss wrtif gnirmo ietI rehSO ta tserdda eheb slow or SIsO memreb ydob in toc ehtnury fo tr ehtseuqeer. ISO copyrithg fo

13、fiec tsop esaCela 65 G 1121-HCeneva 02 T.le + 22 14 10 947 11 Fxa + 14 47 2290 9 74 E-liam cpoyrigthsio.ch Web wwwsi.oc.h BSISO156371:2002 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of pre

14、paring International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in

15、 liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft Interna

16、tional Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 15

17、637 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 15637-1 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 5, Grinding wheels and abrasives. ISO 15637 consists of the followi

18、ng parts, under the general title Holding fixtures of cylindrical abrasive sleeves: Part 1: Holding fixtures with shank for hand-held grinding machines Part 2: Holding fixtures for stationary machines BSISO156371:2002 ANRETNIITOTS LANDNADRA OSI -736512002:1)E(1 Holding fixtures of cylindrical abrasi

19、ve sleeves Part 1: Holding fixtures with shank for hand-held grinding machines 1 Scope This part of ISO 15637 applies to holding fixtures with shank for use with cylindrical abrasive sleeves within accordance with ISO 2421. Holding fixtures with shank having a diameter mostly have lamellar cores and

20、 are used on hand-held grinding machines. The impact of centrifugal forces on the lamellae result in an increase in diameter and thereby clamp the abrasive sleeve on to the holding fixture. 2 Normative reference The following normative document contains provisions which, through reference in this te

21、xt, constitute provisions of this part of ISO 15637. For dated references, subsequent amendments to, or revisions of, this publication do not apply. However, parties to agreements based on this part of ISO 15637 are encouraged to investigate the possibility of applying the most recent edition of the

22、 normative document indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 2421: 1) , Coated abrasives Cylindrical sleeves 3 Design and dimensions 3.1 Design

23、The shape and design of the holding fixtures with shank are at the manufacturers discretion; only the specified dimensions and tolerances shall be observed. See Figure 1. 1) To be published. (Revision of ISO 2421:1972) Figure 1 D 100 mm D 100 mm BSISO156371:2002 2 3.2 Dimensions See Table 1. 4 Requi

24、rements 4.1 Holding fixtures These shall be made of rubber the type of which is left to the manufacturers discretion. 4.2 Shank This shall be made of steel having a minimum yield strength, and whose class is left to the manufacturers discretion. 5 Designation A holding fixture conforming to this par

25、t of ISO 15637 shall be designated by a) “Holding fixture”; b) reference to this part of ISO 15637, i.e. ISO 15637-1; c) its dimensions , and , in millimetres; d) its maximum operating speed , in metres per second. Table 1 Dimensions Dimensions in millimetres Nominal Limit deviations 10 10 6 40 20 1

26、5 10 30 22 20 40 30 20 30 40 50 45 30 40 50 60 30 6 or 8 40 50 75 30 8 40 50 100 40 DTSL 1h 9 3 +0,5 0 +0,5 0 +0,4 0,1 +0,4 0,1 +0,4 0,1 0,3 +0,4 0,3 +0,4 0,3 R e = 300 N/mm 2 DT S v s BSISO156371:2002 3 EXAMPLE A holding fixture with diameter , thickness , shank diameter and maximum operating speed

27、 is designated as follows: Holding fixture ISO 15637-1 - 45 30 6/40 6M a r k i n g The marking of holding fixtures with shank is left to the manufacturers discretion. D= 45 mm T = 30 mm S= 6mm v s = 40 m/s BSISO156371:2002 BS ISO 15637-1:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Stan

28、dards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British S

29、tandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the tech

30、nical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying s

31、tandards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international

32、standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical H

33、elp to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with stand

34、ards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via B

35、ritish Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Exce

36、pt as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in

37、the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.