BS ISO 12614-8-2014 Road vehicles Liquefied natural gas (LNG) fuel system components Excess flow valve《道路车辆 液化天然气 (LNG) 燃料系统部件 溢流阀》.pdf

《BS ISO 12614-8-2014 Road vehicles Liquefied natural gas (LNG) fuel system components Excess flow valve《道路车辆 液化天然气 (LNG) 燃料系统部件 溢流阀》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 12614-8-2014 Road vehicles Liquefied natural gas (LNG) fuel system components Excess flow valve《道路车辆 液化天然气 (LNG) 燃料系统部件 溢流阀》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 12614-8:2014Road vehicles Liquefiednatural gas (LNG) fuel systemcomponentsPart 8: Excess flow valveBS ISO 12614-8:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 12614-8:2014.The UK participation in its preparation was entru

2、sted to TechnicalCommittee GSE/40, Gas supply equipment for natural gas vehicles.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its corr

3、ectapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 77155 2ICS 43.060.40Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy

4、 Committee on 31 July 2014.Amendments issued since publicationDate Text affectedBS ISO 12614-8:2014 ISO 2014Road vehicles Liquefied natural gas (LNG) fuel system components Part 8: Excess flow valveVhicules routiers quipements pour vhicules utilisant le gaz naturel liqufi (GNL) comme combustible Par

5、tie 8: Valve de limitation de dbitINTERNATIONAL STANDARDISO12614-8First edition2014-07-01Reference numberISO 12614-8:2014(E)BS ISO 12614-8:2014ISO 12614-8:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publi

6、cation may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the count

7、ry of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 12614-8:2014ISO 12614-8:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative refe

8、rences 13 Terms and definitions . 14 Marking 25 Construction and assembly . 26 Test 36.1 Applicability 36.2 Hydrostatic strength 36.3 Leakage 36.4 Excess torque resistance 46.5 Bending moment . 46.6 Continued operation 46.7 Operation . 4Bibliography 5BS ISO 12614-8:2014ISO 12614-8:2014(E)ForewordISO

9、 (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical com

10、mittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrot

11、echnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was draft

12、ed in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent righ

13、ts. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitu

14、te an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe commit

15、tee responsible for this document is ISO/TC 22, Road vehicles, Subcommittee SC 25, Vehicles using gaseous fuels.ISO 12614 consists of the following parts, under the general title Road vehicles Liquefied natural gas (LNG) fuel system components: Part 1: General requirements and definitions Part 2: Pe

16、rformance and general test methods Part 3: Check valve Part 4: Manual valve Part 5: Tank pressure gauge Part 6: Pressure regulator Part 7: Pressure relief valve Part 8: Excess flow valve Part 9: Gas-tight housing and ventilation hose Part 10: Rigid fuel line in stainless steel Part 11: Fittings Part

17、 12: Rigid fuel line in copper and its alloys Part 13: Pressure control regulator Part 14: Differential pressure fuel content gauge Part 15: Capacitance fuel content gaugeiv ISO 2014 All rights reservedBS ISO 12614-8:2014ISO 12614-8:2014(E) Part 16: Heat exchanger vaporizer Part 17: Natural gas dete

18、ctor Part 18: Gas temperature sensor ISO 2014 All rights reserved vBS ISO 12614-8:2014BS ISO 12614-8:2014Road vehicles Liquefied natural gas (LNG) fuel system components Part 8: Excess flow valve1 ScopeThis part of ISO 12614 specifies tests and requirements for the excess flow valve, a liquefied nat

19、ural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This part of ISO 12614 is applicable to vehicles using natural gas in accordance with ISO 15403 (mono-fuel, bi-fuel, or dual-fuel applications). It is not applicable to the following:a) fuel container

20、s;b) stationary gas engines;c) container mounting hardware;d) electronic fuel management;e) refueling receptacles.NOTE 1 It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this part of ISO 12614 and tested according to the appropria

21、te functional tests.NOTE 2 All references to pressure in this part of ISO 12614 are to be considered gauge pressures unless otherwise specified.NOTE 3 This part of ISO 12614 is based upon a working pressure for natural gas as a fuel of 1,6 MPa (16 bar). (1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.) O

22、ther working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, a 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.2 Normative referencesThe following documents, in whole or in part, are normatively referenced

23、 in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 12614-1, Road vehicles Liquefied natural gas (LNG) fuel system components Pa

24、rt 1: General requirements and definitionsISO 12614-2, Road vehicles Liquefied natural gas (LNG) fuel system components Part 2: Performance and general test methods3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 12614-1 and the following apply.3.1inte

25、rnal excess flow valveexcess flow valve installed inside the cylinder or cylinder valveINTERNATIONAL STANDARD ISO 12614-8:2014(E) ISO 2014 All rights reserved 1BS ISO 12614-8:2014ISO 12614-8:2014(E)3.2external excess flow valveexcess flow valve installed outside the cylinder or cylinder valve3.3shut

26、-off type excess flow valveexcess flow valve that stops flow when in the closed position3.4flow-limiter type excess flow valveexcess flow valve that limits flow when activatedNote 1 to entry: The device resets automatically when the excess flow condition is no longer present.3.5activationdifferentia

27、l pressure flow or other condition specified by the manufacturer at which the excess flow valve is activated4 MarkingMarking of the component shall provide sufficient information to allow the following to be traced:a) the manufacturers or agents name, trademark, or symbol;b) the model designation (p

28、art number);c) the operating specifications (working pressure, temperature range, excess flow valve type, activation flow, or P, max. flow when activated).The following additional markings are recommended:a) the direction of flow (when necessary for correct installation);b) the type of fuel;c) elect

29、rical ratings (if applicable);d) the symbol of the certification agency;e) the type approval number;f) the serial number or date code;g) a reference to this part of ISO 12614 (i.e. ISO 12614-8:2014).NOTE This information can be provided by a suitable identification code on at least one part of the c

30、omponent when it consists of more than one part.5 Construction and assemblyThe excess flow valve shall comply with the applicable provisions of ISO 12614-1 and ISO 12614-2, and with the tests specified in Clause 6.2 ISO 2014 All rights reservedBS ISO 12614-8:2014ISO 12614-8:2014(E)6 Test6.1 Applicab

31、ilityThere are many types of excess flow valves available. This part of ISO 12614 provides requirements for two different designs: internal and external excess flow valves. A valve of either design could be one of two different types: shut-off or flow-limiter. As excess flow valve designs vary, so w

32、ill the tests required.The function of an excess flow valve can be achieved in other ways. For example, instead of using a mechanical device, an electronic system can be adopted to ensure the closing or limiting of the gas flow from the cylinder in an accident.The tests required to be carried out ar

33、e indicated in Table 1.Table 1 Tests applicableTest ApplicableTest procedure as required by ISO 12614-2Specific test requirements of this part of ISO 12614Hydrostatic strength X X X (see 6.2)Leakage X X X (see 6.3)Excess torque resistance X X X (see 6.4)Bending moment X X X (see 6.5)Continued operat

34、ion X X X (see 6.6)Corrosion resistance X XOxygen ageing X XNon-metallic synthetic immersion X XVibration resistance X XBrass material compatibility X XOperation X X (see 6.7)6.2 Hydrostatic strengthTest the excess flow valve according to the procedure for testing hydrostatic strength specified in I

35、SO 12614-2. For internal or external excess flow valves, the test pressure shall be 2,5 times the working pressure.6.3 LeakageThe internal leakage test shall be conducted on shut-off type excess flow valves. The excess flow valve shall have an internal leakage rate less than 30 Ncm3/h.Test the exces

36、s flow valve at the temperatures and pressures given in Table 2.Table 2 Test temperatures and pressuresTemperature CFirst test pressure Second test pressure160 1,0 working pressure Operational pressure20 Operational pressure1,5 working pressure85 Operational pressure ISO 2014 All rights reserved 3BS

37、 ISO 12614-8:2014ISO 12614-8:2014(E)6.4 Excess torque resistanceThe excess torque resistance test shall be conducted only on external excess flow valves. See ISO 12614-2.6.5 Bending momentThe bending moment test shall be conducted only on external excess flow valves. See ISO 12614-2.6.6 Continued op

38、eration6.6.1 Cycle the excess flow valve 20 times at working pressure differential pressure. One cycle shall consist of one opening and one closing. Upon completion of the test, the valve shall comply with 6.3 and 6.7.6.6.2 Following cycling, operation, and leakage retesting, perform the hydrostatic

39、 test in accordance with 6.2.6.7 OperationMeasure the activation flow or P and the flow of the excess flow valve when it activates. Perform the test using the activation conditions stated by the manufacturer; the measured flows and pressures shall meet the manufacturers specified flow.4 ISO 2014 All

40、 rights reservedBS ISO 12614-8:2014ISO 12614-8:2014(E)Bibliography1 ISO 3833, Road vehicles Types Terms and definitions ISO 2014 All rights reserved 5BS ISO 12614-8:2014ISO 12614-8:2014(E) ISO 2014 All rights reservedICS 43.060.40Price based on 5 pagesThis page deliberately left blankBSI is the nati

41、onal body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Head

42、quarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependa

43、ble format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standar

44、ds by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased.

45、If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription

46、products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive

47、substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or

48、replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as

49、theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication p