BS EN ISO 25178-72-2017 Geometrical product specifications (GPS) Surface texture Areal XML file format x3p《几何产品规格(全球定位系统) 表面纹理 地域 XML文件格式x3p》.pdf

《BS EN ISO 25178-72-2017 Geometrical product specifications (GPS) Surface texture Areal XML file format x3p《几何产品规格(全球定位系统) 表面纹理 地域 XML文件格式x3p》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 25178-72-2017 Geometrical product specifications (GPS) Surface texture Areal XML file format x3p《几何产品规格(全球定位系统) 表面纹理 地域 XML文件格式x3p》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、Geometrical product specifications (GPS) Surface texture: ArealPart 72: XML file format x3p (ISO 25178-72:2017)BS EN ISO 25178-72:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 25178-72 June 2017 ICS 17.04

2、0.20 English Version Geometrical product specifications (GPS) - Surface texture: Areal - Part 72: XML file format x3p (ISO 25178-72:2017)Spcification gomtrique des produits (GPS) - tat de surface: Surfacique - Partie 72: Format de fichier XML x3p (ISO 25178-72:2017) Geometrische Produktspezifikation

3、 (GPS) - Oberflchenbeschaffenheit: Flchenhaft - Teil 72: XML Dateiformat x3p (ISO 25178-72:2017) This European Standard was approved by CEN on 24 April 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the

4、 status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, Frenc

5、h, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria,

6、Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

7、Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Member

8、s. Ref. No. EN ISO 25178-72:2017 ENational forewordThis British Standard is the UK implementation of EN ISO 25178-72:2017. The UK participation in its preparation was entrusted to Technical Committee TDW/4, Technical Product Realization.A list of organizations represented on this committee can be ob

9、tained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017Published by BSI Standards Limited 2017ISBN 978 0 580 80931 6ICS 17.040.40; 17.040.20Co

10、mpliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 25178-72:201

11、7EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 25178-72 June 2017 ICS 17.040.20 English Version Geometrical product specifications (GPS) - Surface texture: Areal - Part 72: XML file format x3p (ISO 25178-72:2017)Spcification gomtrique des produits (GPS) - tat de surface: Surfacique - Part

12、ie 72: Format de fichier XML x3p (ISO 25178-72:2017) Geometrische Produktspezifikation (GPS) - Oberflchenbeschaffenheit: Flchenhaft - Teil 72: XML Dateiformat x3p (ISO 25178-72:2017) This European Standard was approved by CEN on 24 April 2017. CEN members are bound to comply with the CEN/CENELEC Int

13、ernal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to an

14、y CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official v

15、ersions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norwa

16、y, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights o

17、f exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 25178-72:2017 EBS EN ISO 25178-72:2017EN ISO 25178-72:2017 (E) 2 European foreword This document (EN ISO 25178-72:2017) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geomet

18、rical product specifications and verification“ in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publi

19、cation of an identical text or by endorsement, at the latest by December 2017, and conflicting national standards shall be withdrawn at the latest by December 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELE

20、C shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic

21、, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

22、Endorsement notice The text of ISO 25178-72:2017 has been approved by CEN as EN ISO 25178-72:2017 without any modification. ISO 25178-72:2017(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Requirements 44.1 Units . 44.2 Recommended offset value 45 x3p file

23、 format . 45.1 General . 45.2 File name extension 45.3 Minimum contents of zip-container . 45.4 Optional contents of zip-container 45.4.1 General 45.4.2 Binary encoded coordinates 55.4.3 Validity mask . 55.4.4 Vendor specific extensions 55.5 Contents and format of main.xml 55.5.1 General 55.5.2 Main

24、 records 55.5.3 Record1: Header, data types, and axes definitions . 55.5.4 Record2: Meta data 85.5.5 Record3: 3D point data105.5.6 Record4: Checksum information 145.5.7 Vendor specific extensions . 14Annex A (informative) XML file format .15Annex B (informative) Sample main.xml 20Annex C (informativ

25、e) Relation with the GPS matrix .22Bibliography .23 ISO 2017 All rights reserved iiiContents PageBS EN ISO 25178-72:2017ISO 25178-72:2017(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Requirements 44.1 Units . 44.2 Recommended offset value 45 x3p file for

26、mat . 45.1 General . 45.2 File name extension 45.3 Minimum contents of zip-container . 45.4 Optional contents of zip-container 45.4.1 General 45.4.2 Binary encoded coordinates 55.4.3 Validity mask . 55.4.4 Vendor specific extensions 55.5 Contents and format of main.xml 55.5.1 General 55.5.2 Main rec

27、ords 55.5.3 Record1: Header, data types, and axes definitions . 55.5.4 Record2: Meta data 85.5.5 Record3: 3D point data105.5.6 Record4: Checksum information 145.5.7 Vendor specific extensions . 14Annex A (informative) XML file format .15Annex B (informative) Sample main.xml 20Annex C (informative) R

28、elation with the GPS matrix .22Bibliography .23 ISO 2017 All rights reserved iiiContents PageBS EN ISO 25178-72:2017ISO 25178-72:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing I

29、nternational Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison

30、 with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directi

31、ves, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that so

32、me of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declar

33、ations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity

34、assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical produc

35、t specifications and verification.A list of all parts in the ISO 25178 series can be found on the ISO website.iv ISO 2017 All rights reservedBS EN ISO 25178-72:2017ISO 25178-72:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bod

36、ies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organization

37、s, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further

38、maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directive

39、s).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Intr

40、oduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO speci

41、fic terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committe

42、e ISO/TC 213, Dimensional and geometrical product specifications and verification.A list of all parts in the ISO 25178 series can be found on the ISO website.iv ISO 2017 All rights reserved ISO 25178-72:2017(E)IntroductionThis document is a geometrical product specification (GPS) standard and is to

43、be regarded as a general GPS standard (see ISO 14638). It influences the chain link F of the chains of standards on profile and areal surface texture.The ISO/GPS matrix model given in ISO 14638 gives an overview of the ISO/GPS system of which this document is a part. The fundamental rules of ISO/GPS

44、 given in ISO 8015 apply to this document and the default decision rules given in ISO 14253-1 apply to the specifications made in accordance with this document, unless otherwise indicated.For more detailed information of the relation of this document to other standards and the GPS matrix model, see

45、Annex C.The x3p format was in use in industry and academia before the creation of this document. The x3p file format as defined in this document has been developed based on the definitions in ISO 5436-2. The openGPS1)consortium provides a free open source software implementation of this file format

46、to avoid the inevitable inconsistency of multiple proprietary implementations.1) openGPSis an example of a suitable product available commercially. This information is given for the convenience of users of this document and does not constitute an endorsement by ISO of this product. ISO 2017 All righ

47、ts reserved vBS EN ISO 25178-72:2017BS EN ISO 25178-72:2017Geometrical product specifications (GPS) Surface texture: Areal Part 72: XML file format x3p1 ScopeThis document defines the XML file format x3p for storage and exchange of topography and profile data.2 Normative referencesThe following docu

48、ment is referred to in the text in such a way that some or all of its content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 25178-6002), Geo

49、metrical product specifications (GPS) Surface texture: Areal Part 600: Metrological characteristics for areal-topography measuring methods3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 25178-600 and the following apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp IEC Electropedia: available at h t t p :/ www .electropedia .org/ 3.1zip-containerfile form