BS EN ISO 105-A06-1997 Textiles Tests for colour fastness Instrumental determination of 1 1 standard depth of colour《纺织品 色牢度试验 颜色的1 1标准深度仪器测定》.pdf

《BS EN ISO 105-A06-1997 Textiles Tests for colour fastness Instrumental determination of 1 1 standard depth of colour《纺织品 色牢度试验 颜色的1 1标准深度仪器测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 105-A06-1997 Textiles Tests for colour fastness Instrumental determination of 1 1 standard depth of colour《纺织品 色牢度试验 颜色的1 1标准深度仪器测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 105-A06:1997 Textiles Tests for colour fastness Part A06: Instrumental determination of 1/1 standard depth of colour (ISO 105-A06:1995) The European Standard EN ISO 105-A06:1997 has the status of a British Standard ICS 59.080.01BSENISO105-A06:1997 This British Standard, ha

2、ving been prepared under the directionof the Sector BoardforMaterials and Chemicals, waspublished underthe authorityof the Standards Boardand comes into effect on 15 August 1997 BSI 09-1999 ISBN 0 580 27817 4 National foreword This British Standard is the English language version of ENISO105-A06:199

3、7. It is identical withISO105-A06:1995. The UK participation in its preparation was entrusted by Technical Committee TCI/25, Chemical properties, to Subcommittee TCI/25/-/10, Colour fastness, which has the responsibility to: aid enquirers to understand the text; present to the responsible internatio

4、nal/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its s

5、ecretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or using the “Find” facility of the BSI Standard

6、s Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages

7、This document comprises a front cover, an inside front cover, pages i and ii, the EN ISO title page, page 2, the ISO title page, pages ii to iv, pages 1 to 3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the

8、amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSENISO105-A06:1997 BSI 09-1999 i Contents Page National foreword Inside front cover Foreword 2 Foreword iii Text of ISO 105-A06 1ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 105-

9、A06 April 1997 ICS 59.080.01 Descriptors: See ISO document English version Textiles Tests for colour fastness PartA06:Instrumental determination of 1/1 standard depth of colour (ISO 105-A06:1995) Textiles Essais de solidit des teintures Partie A06: Mthode instrumentale pour la dtermination de la pro

10、fondeur de nuance standard 1/1 (ISO 105-A06:1995) Textilien Farbechtheitsprfungen Teil A06: Farbmetrisch- Bestimmung der 1/1 Richttyptiefe (ISO 105-A06:1995)This European Standard was approved by CEN on 1997-03-28. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipu

11、late the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards ex

12、ist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bo

13、dies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Sec

14、retariat: rue de Stassart 36, B-1050 Brussels 1997 CEN ALL rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 105-A06:1997 EENISO105-A06:1997 BSI 09-1999 2 Foreword The text of the International Standard from Technical Committee ISO/TC 38

15、 “Textiles” of the International Organization for Standardization (ISO) has been taken over as an European Standard by Technical Committee CEN/TC 248 “Textiles and textile products”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, eit

16、her by publication of an identical text or by endorsement, at the latest by October 1997, and conflicting national standards shall be withdrawn at the latest by October 1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound

17、to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO105-A06:1995has been a

18、pproved by CEN as a European Standard without any modification.ENISO105-A06:1997 ii BSI 09-1999 Contents Page Foreword iii 1 Scope 1 2 Normative reference 1 3 Principle 1 4 Apparatus 1 5 Test specimen 1 6 Procedure 1 7 Calculation 1 8 Test report 2 Annex A (informative) Representative test data 3 An

19、nex B (informative) Corrective action 3 Table 1 Limiting angles h nand coefficients K n,mof the polynomial P 2 Table A.1 Test data for computer program check of %L calculation 3ENISO105-A06:1997 BSI 09-1999 iii Foreword ISO (the International Organization for Standardization) is a worldwide federati

20、on of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee

21、. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the techni

22、cal committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least75% of the member bodies casting a vote. International StandardISO105-A06 was prepared by Technical Committee ISO/TC38, Textiles, Subcommittee SC 1, Tests for coloured

23、 textiles and colorants. ISO 105 was previously published in thirteen “parts”, each designated by a letter (e.g. “Part A”), with publication dates between 1978 and 1985. Each part contained a series of “sections”, each designated by the respective part letter and by a two-digit serial number (e.g. “

24、Section A01”). These sections are now being republished as separate documents, themselves designated “parts” but retaining their earlier alphanumeric designations. A complete list of these parts is given inISO105-A01. Annex A andAnnex B of this part ofISO105 are for information only. Descriptors: Te

25、xtiles, dyes, tests, determination, colour fastness, depth.iv blankENISO105-A06:1997 BSI 09-1999 1 1 Scope This method is intended for determining 1/1 standard depth of a dyeing on any textile material by a colorimetric method as a permitted alternative to the visual method described in clause12 of

26、ISO105-A01:1994. This method is applicable to 1/1 standard depth of colour only. Its use for other standard depths is under consideration. NOTE 1Specimens which this colorimetric method indicate to be of 1/1 standard depth may differ from specimens which are visually assessed to be of 1/1 standard d

27、epth by comparison with physical standards known to be of 1/1 standard depth. These differences may lead to differences in the results of tests applied subsequently. It is recommended that the method of assessment of 1/1 standard depth, i.e. ISO105-A06 or visual, be included in the report of tests s

28、ubsequently applied. 2 Normative reference The following standard contains provisions which, through reference in this text, constitute provisions of this part ofISO105. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements base

29、d on this part ofISO105 are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. CIE Publication No. 15.2:1986 Colorimetry, (second edition) 1) . 3 Principl

30、e The CIELAB colour coordinates L* (lightness), C* ab(chroma) and h ab(hue) of the dyeing to be checked for 1/1 standard depth are measured instrumentally. The lightness L SDfor 1/1 standard depth is calculated by means of a given equation. The lightness difference %L between the measured lightness

31、L* of the dyeing and the calculated lightness L SDrequired for 1/1 standard depth is determined to decide if the dyeing represents 1/1 standard depth. 4 Apparatus 4.1 Spectrophotometer or colorimeter, meeting any one of the definitions described in CIE publication15.2, subclause 1.4. 5 Test specimen

32、 Cut a representative specimen of the dyeing to be checked for 1/1 standard depth and mount it on an opaque white backing which has not been pretreated with a fluorescent whitening agent. The size of the specimen shall fit at least the aperture of the instrument to be used for measurement. A minimal

33、 specimen size of50mm 50mm is recommended. When presented to the instrument, the specimen shall be of sufficient thickness to be opaque, otherwise light will pass through the specimen and reflect off the backing material. Check the opacity of the specimen by measuring it over a black background and

34、separately over a white background. If complete opacity cannot be achieved, then it is sufficient if the difference between the L* resulting from measurements over black and white backgrounds is less than0,2. 6 Procedure Place the test specimen against the sample port of the instrument in such a way

35、 that it provides a smooth surface and read the CIELAB coordinates L* (lightness), C* ab(chroma) and h ab(hue), using the CIE10 observer and illuminant D65. Take at least two readings, preferably from different areas of the test specimen, and average them. 7 Calculation 7.1 Calculate the lightness L

36、 SDrequired for 1/1 standard depth using the equation: L SD=20,4+ CP + 6 exp ( CP/6) where in which 1) Available from the Central Bureau of the CIE, Kegelgasse 27, A-1030 Vienna, Austria. h n are the limiting angles of the different colour sectors in the CIELAB colour diagram, for n = 1 to 9; K n,m

37、are the coefficients of the polynominal P, for m = 0 to 3. h nand K n,mare listed inTable 1.ENISO105-A06:1997 2 BSI 09-1999 7.2 Calcualte the lightness difference between the measured and calculated values: %L = L* L SD . If%L is not more than 0,5, the specimen represents1/1 standard depth of colour

38、. 7.3 Typical data which may be used to verify a computer program for direct calculation of %L are given inAnnex A.Annex B suggests corrective action if the test specimen does not adequately represent 1/1 standard depth. 8 Test report The test report shall include the following information: a) the n

39、umber and year of publication of this part of ISO 105; i.e. ISO 105-A06:1995; b) all details necessary for complete identification of the sample tested; c) identification of the spectrophotometer or colorimeter used, including the CIE geometry type selected; d) the value of %L calculated for the sam

40、ple (see7.2); e) the test date. Table 1 Limiting angles h nand coefficients K n,mof the polynomial P n h n K n,0 K n,1 K n,2 K n,3 1 0 3,27 10 1 1,73 10 3 2,13 10 5 8,68 10 7 2 52 4,81 10 1 6,57 10 3 1,14 10 4 3,50 10 6 3 79 6,73 10 1 5,08 10 3 1,69 10 4 1,07 10 6 4 135 6,14 10 1 3,83 10 3 1,02 10 5

41、 6,40 10 8 5 203 4,21 10 1 1,56 10 3 2,32 10 5 4,82 10 7 6 267 2,90 10 1 4,51 10 3 6,93 10 5 2,43 10 6 7 302 1,51 10 1 4,40 10 4 1,85 10 4 2,30 10 6 8 340 2,76 10 1 3,69 10 3 7,66 10 5 9,22 10 7 9 360 3,27 10 1 1,73 10 3 2,13 10 5 8,68 10 7ENISO105-A06:1997 BSI 09-1999 3 Annex A (informative) Repres

42、entative test data To help check computer programs giving %L values directly from measured colour coordinates of the test specimen, some representative test data are given inTable A.1. Table A.1 Test data for computer program check of %L calculation Annex B (informative) Corrective action If the lig

43、htness difference %L is greater than 0,5, the test specimen does not adequately represent 1/1 standard depth. A fresh dyeing should be made using a lower concentration of dye if %L is negative, or a higher concentration of dye if %L is positive. L* C* ab h ab %L 30,0 20,0 0,0 + 1,043 30,0 20,0 1,0 +

44、 1,020 30,0 20,0 180,0 1,023 30,0 20,0 359,0 + 1,072BS EN ISO 105-A06:1997 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international

45、level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be

46、grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service

47、called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international

48、 standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical H

49、elp to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits