BS EN 60534-8-2-2011 Industrial-process control valves Noise considerations Laboratory measurement of noise generated by hydrodynamic flow through control valves《工业过程控制阀 流动液流经控制阀产生.pdf

《BS EN 60534-8-2-2011 Industrial-process control valves Noise considerations Laboratory measurement of noise generated by hydrodynamic flow through control valves《工业过程控制阀 流动液流经控制阀产生.pdf》由会员分享，可在线阅读，更多相关《BS EN 60534-8-2-2011 Industrial-process control valves Noise considerations Laboratory measurement of noise generated by hydrodynamic flow through control valves《工业过程控制阀 流动液流经控制阀产生.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationIndustrial-process control valvesPart 8-2: Noise considerations Laboratory measurement of noise generated by hydrodynamic flow through control valvesBS EN 60534-8-2:2011Copyright

2、 European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-National forewordThis British Standard is the UK implementation of EN 60534-8-2:2011. It is identical to IEC 60534-8-2

3、:2011. It supersedes BS EN 60534-8-2:1993, which will be withdrawn on 16 November 2014.The UK participation in its preparation was entrusted by Technical Committee GEL/65, Measurement and control, to Subcommittee GEL/65/2, Elements of systems.A list of organizations represented on this committee can

4、 be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012 ISBN 978 0 580 76471 4 ICS 17.140.20; 23.

5、060.40; 25.040.40 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Stand-ards Policy and Strategy Committee on 31 August 2012.Amendments issued since publicationDate Text affectedBRITISH STANDARDBS EN 6053

6、4-8-2:2011Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD EN 60534-8-2 NORME EUROPENNE EUROPISCHE NORM December 2011 CENELEC European Commi

7、ttee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC memb

8、ers. Ref. No. EN 60534-8-2:2011 E ICS 17.140.20; 23.060.40; 25.040.40 Supersedes EN 60534-8-2:1993English version Industrial-process control valves - Part 8-2: Noise considerations - Laboratory measurement of noise generated by hydrodynamic flow through control valves (IEC 60534-8-2:2011) Vannes de

9、rgulation des processus industriels - Partie 8-2: Considrations sur le bruit - Mesure en laboratoire du bruit cr par un coulement hydrodynamique dans une vanne de rgulation (CEI 60534-8-2:2011) Stellventile fr die Prozeregelung - Teil 8-2: Geruschemission - Laboratoriumsmessungen von Geruschen bei f

10、lssigkeitsdurchstrmten Stellventilen (IEC 60534-8-2:2011) This European Standard was approved by CENELEC on 2011-11-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard wit

11、hout any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any o

12、ther language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cy

13、prus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60534-8-2:2011Copyrig

14、ht European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 60534-8-2:2011 - 2 - Foreword The text of document 65B/801/FDIS, future edition 2 of IEC 60534-8-2, prepared by S

15、C 65B, “Devices b) decrease the pressure ratio xFin such a way that there is a transition from cavitating to non-cavitating flow and measure Lpas a function of frequency for each value of xFused; c) from the data obtained in b), determine the approximate frequency which gives the maximum Lpresponse.

16、 This is the peak frequency; d) using a sound level meter with an octave band filter that includes the peak frequency, measure the Lpas xFis decreased. The range of xFshall be sufficient to establish the curves in both the cavitating and non-cavitating regions; e) in both the cavitating and non-cavi

17、tating regions, fit a straight line through the data points. The intersection of the straight lines shall determine the value of xFz. See point A in Figure 5; f) repeat the procedure for the other relative flow coefficients given in Clause 8. 8.3.2 A-weighted method This method of determining xFzreq

18、uires the measurement of the overall sound pressure level (LpA) using the A-weighted method. The procedure is as follows (refer to Figure 6): a) at a given travel (corresponding to one of the relative flow coefficients given in Clause 8), the LpAversus xFcurve as shown by the dashed line shall be de

19、termined. Decrease the pressure ratio xFin such a way that there is a transition from cavitating to non-cavitating flow and measure LpAfor each value of xFused; b) from the above curve, xF3and xF6, which are the approximate values at which the LpAcurve changes slope, shall be determined; c) the rang

20、es xFIand xFIIshall each be divided into three equal parts (designated as “a“ and “b“, respectively); d) at each of the values xF6through xF1, the A-weighted overall sound pressure level shall be measured. This procedure shall be repeated twice so that there are three series of measurements; e) for

21、each value of xF, the arithmetic average, pAL , of the three LpAvalues shall be calculated and the points plotted; BS EN 60534-8-2:2011Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted wit

22、hout license from IHS-,-,- 14 60534-8-2 IEC:2011 f) using the values of pAL at xF1through xF6, the curves designated as lines 1 and 2 shall be determined by linear regression; g) the point at which lines 1 and 2 intersect shall be determined. The value of xFat this point is xFz; h) repeat the proced

23、ure for the other relative flow coefficients given in Clause 8. T P P PC F TC 9b 9 14 11 12 15 10 13 8 1 2 3 4 4b 5 6 5 7 IEC 2131/11 NOTES System components 1 See Figure 2a or 2b for placement of item 8 (acoustic environment) and item 10 (microphone) 2 Items 8, 12 and 15 are optional 1 = pump 2 = f

24、low measuring device 3 = upstream throttling valve 4 = temperature measuring device 4b = upstream in-line silencer (if necessary) 5 = pressure measuring device 6 = test specimen 7 = test section piping 8 = acoustic environment (test chamber) (Notes 1 and 2) 9 = downstream throttling valve 9b = downs

25、tream in-line silencer (if necessary) 10 = sound level sensor (Note 1) 11 = water tank 12 = temperature controlling device (Note 2) 13 = vessel with air cushion to increase static pressure, if necessary 14 = exhaust valve 15 = pressure controller (Note 2) Figure 1a Control valve closed loop noise te

26、st System components BS EN 60534-8-2:2011Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-60534-8-2 IEC:2011 15 4 T P P PC F 4b 3 5 5 6 7 10 8 2 13 1 15 9b 9

27、IEC 2132/11 NOTES System components 1 See Figure 2a or 2b for placement of item 8 (acoustic environment) and item 10 (microphone) 2 Items 8, 12 and 15 are optional 1 = pump 2 = flow measuring device 3 = upstream throttling valve 4 = temperature measuring device 4b = upstream in-line silencer (if nec

28、essary) 5 = pressure measuring device 6 = test specimen 7 = test section piping 8 = acoustic environment (test chamber) (Notes 1 and 2) 9 = downstream throttling valve 9b = downstream in-line silencer (if necessary) 10 = sound level sensor (Note 1) 11 = water tank 13 = vessel with air cushion to inc

29、rease static pressure, if necessary 15 = pressure controller (Note 2) Figure 1b Control valve open loop noise test System components Figure 1 System components for control valve closed loop and open loop noise test BS EN 60534-8-2:2011Copyright European Committee for Electrotechnical Standardization

30、 Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 16 60534-8-2 IEC:2011 T 2 8 2 m Note 4 1,0 m 1,0 m Flow 10 1,0 m (Note2) Seal between chamber and pipe at both ends Seals shall not damp pipe vibrations to extent that noise

31、 measurements are affected P 2 5 4 7 0,5 m According to IEC 60534-2-3 6 IEC 2133/11 NOTES System components 1 D = nominal pipe diameter of outlet pipe, in mm 4 temperature measuring device 2 The sound level sensor shall be located at a distance of 1 m from the outer surface to the pipe and should be

32、 no closer than 0,5 m to the nearest chamber surface. 5 pressure measuring device 3 The test section piping inside the test chamber should be continuous with no flanges, circumferential joints, or other pipewall reinforcements. 6 test specimen 4 For specimens 150 mm (6 in) and smaller, 1,0 m minimum

33、 and 3,0 m maximum. Above 150 mm size, 6 D minimum and 20 D maximum should be held (see Clause 6 for further clarification). 7 test section piping (Note 3) 8 acoustic environment (test chamber) 10 sound level sensor (Note 2) Figure 2a Test arrangement with test specimen outside acoustic environment

34、BS EN 60534-8-2:2011Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-60534-8-2 IEC:2011 17 T 2 6 Note 4 1,0 m 0,5 m (Note2) 1,0 m (Note2) Flow 10 According to

35、 IEC 60534-2-3 8 7 0,5 m 5 P 2 4 Seal between chamber and pipe at both ends Seals shall not damp pipe vibrations to extent that noise measurements are affected IEC 2134/11 NOTES System components 1 D = nominal pipe diameter of outlet pipe, in mm 4 temperature measuring device 2 The sound level senso

36、r should be located at a distance of 1 m from the outer surface of the pipe and shall be no closer than 0,5 m to the nearest chamber surface. 5 pressure measuring device 3 The test section piping inside the test chamber should be continuous with no flanges, circumferential joints, or other pipewall

37、reinforcements. 6 test specimen 4 For specimens 150 mm (6 in) and smaller, 1,0 m minimum and 3,0 m maximum. Above 150 mm size, 6 D minimum and 20 D maximum should be held (see Clause 6 for further clarification). 7 test section piping (Note 3) 8 acoustic environment (test chamber) 10 sound level sen

38、sor (Note 2) Figure 2b Alternative test arrangement with test specimen inside acoustic environment Figure 2 Test arrangements with specimen outside and (alternatively) inside acoustic environment BS EN 60534-8-2:2011Copyright European Committee for Electrotechnical Standardization Provided by IHS un

39、der license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 18 60534-8-2 IEC:2011 0 Relative flow coefficient CharacteristicpressureratioxFz0,25 0,5 0,75 1,00 IEC 2135/11 Figure 3 Typical curve for characteristic pressure ratio xFz Surface finish Ra IE

40、C 2136/11 Dimensions in millimetres Figure 4 Reference test orifice plate (see 8.2.1) BS EN 60534-8-2:2011Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-605

41、34-8-2 IEC:2011 19 A Soundpressurelevel(dB)Pressure ratio xFxFzIEC 2137/11 Figure 5 Determination of xFzby peak frequency method (see 8.3.1) BS EN 60534-8-2:2011Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction o

42、r networking permitted without license from IHS-,-,- 20 60534-8-2 IEC:2011 Line 1: from xF1, pA1L Line 2: from xF4, pA4LxF2, pA2L xF5, pA5LxF3, pA3L xF6, pA6LDetermined by linear regression LpAdB (A) LpA6LpA5LpA4LpA3LpA2LpA1Line 1 Line 2 xFzxF1xF2xF3xF4xF5xF6xFa a a b b b xFIxFIIFirst measured LpAve

43、rsus xFcurve a = xFI3 b = xFII3 a = xFI3 b = xFII3 LpAArithemetic average of three measured values IEC 2138/11 Figure 6 Determination of xFzby measuring the overall LpA, dB(A), at a constant valve travel BS EN 60534-8-2:2011Copyright European Committee for Electrotechnical Standardization Provided b

44、y IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-60534-8-2 IEC:2011 21 Uneveness Sound level sensor Pipe behind specimen Recommended mounting position h h IEC 2139/11 Figure 7 Mounting position of the sound level meter in the pipe for

45、 h 0,5 mm If it is not possible to keep h, as shown on Figure 7, less than 0,5 mm, the mismatch shall be compensated either by means of a filling compound in a flat angle 8 between sound level meter and pipe wall or by special shaping of the inner pipe wall. BS EN 60534-8-2:2011Copyright European Co

46、mmittee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 22 60534-8-2 IEC:2011 Bibliography ISO 7-1:1994, Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensi

47、ons, tolerances, and designation ISO 65:1981, Carbon steel tubes suitable for screwing in accordance with ISO 7-1 ISO 4200: 1991, Plain end steel tubes, welded and seamless General Tables of dimensions and masses per unit length _ BS EN 60534-8-2:2011Copyright European Committee for Electrotechnical

48、 Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page deliberately left blankCopyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-