BS EN 60534-6-1-1998 Industrial-process control valves - Mounting details for attachment of positioners to control valves - Positioner mounting on linear actuators《工业过程控制阀 控制阀位置控制器.pdf

《BS EN 60534-6-1-1998 Industrial-process control valves - Mounting details for attachment of positioners to control valves - Positioner mounting on linear actuators《工业过程控制阀 控制阀位置控制器.pdf》由会员分享，可在线阅读，更多相关《BS EN 60534-6-1-1998 Industrial-process control valves - Mounting details for attachment of positioners to control valves - Positioner mounting on linear actuators《工业过程控制阀 控制阀位置控制器.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60534-6-1:1998 IEC 60534-6-1: 1997 Industrial-process control valves Part 6: Mounting details for attachment of positioners to control valves Section 1: Positioner mounting on linear actuators The European Standard EN 60534-6-1:1997 has the status of a British Standard ICS 23.

2、060.40BSEN60534-6-1:1998 This British Standard, having been prepared under the directionof the Electrotechnical Sector Board, was published underthe authority of the Standards Board and comes intoeffect on 15 March1998 BSI 04-1999 ISBN 0 580 29354 8 National foreword This British Standard is the Eng

3、lish language version of EN60534-6-1:1997. It is identical with IEC60534-6-1:1997. It partially supersedes BS5793-6:1986, which is an identical standard to IEC534-6 published by IECin1985. IEC534-6 will be withdrawn when IEC60534-6-2 is published at some future date. The UK participation in its prep

4、aration was entrusted by Technical Committee GEL/65, Measurement and control, to Subcommittee GEL/65/2, Elements of systems, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or prop

5、osals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January1997, all IEC publications have the number6

6、0000 added to the old number. For instance, IEC27-1 has been renumbered as IEC60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC stan

7、dards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “In

8、ternational Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with

9、 a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theENtitle page, pages2 to13 and a back cover. This standard has been updated (see copyright date) and may have had amendments

10、 incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN60534-6-1:1998 BSI 04-1999 i Contents Page National foreword Inside front cover Foreword 2 Text of EN 60534-6-1 3ii blankEUROPEAN STANDARD NORME EUROP

11、ENNE EUROPISCHE NORM EN60534-6-1 October 1997 ICS 23.060.40 Descriptors: Industrial-process, control valve, positioners mounting, mounting details, linear actuator English version Industrial-process control valves Part6:Mountingdetailsforattachment of positioners to control valves Section 1: Positio

12、ner mounting on linear actuators (IEC 60534-6-1:1997) Vannes de rgulation des processus industriels Partie6: Dtails dassemblage pour le montage des positionneurs sur les actionneurs de vannes de rgulation Section1:Montagedespositionneurs sur les actionneurs linaires (CEI60534-6-1:1997) Stellventile

13、fr die Prozeregelung Montage-Einzelheiten zur Befestigung von Steilungsreglern an Stellventil-Antriebe Hauptabschnitt1: Montage von Stellungsreglern an Hubantriebe (IEC60534-6-1:1997) This European Standard was approved by CENELEC on1997-10-01. CENELEC members are bound to comply with the CEN/CENELE

14、C Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN

15、ELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions

16、. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardiz

17、ation Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart35, B-1050 Brussels 1997 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN60534-6-1:1997 EEN605

18、34-6-1:1997 BSI 04-1999 2 Foreword The text of document65B/311/FDIS, future edition1 of IEC60534-6-1, prepared by SC65B, Devices, of IEC TC65, Industrial-process measurement and control, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN60534-6-1 on1997-10-01. The follo

19、wing dates were fixed: Endorsement notice The text of the International Standard IEC60534-6-1:1997 was approved by CENELEC as a European Standard without any modification. Contents Page Foreword 2 1 Scope and object 3 2 Definitions 3 3 Basic design principles 3 4 Feedback connection 3 5 Mounting pla

20、te design 3 6 Actuator yoke mounting 3 Figure 1 Dimensions of standardized actuators 4 Figure 2 Drilling and dimensions for feedback connection 8 Figure 3 Mounting plate attachments 11 Figure 4 Mounting plate dimensions 12 Figure 5 U-bolt dimensions 13 latest date by which the EN has to be implement

21、ed at nationallevel by publication of an identicalnational standard or by endorsement (dop) 1998-07-01 latest date by which the national standards conflicting with the ENhave to be withdrawn (dow) 1998-07-01EN60534-6-1:1997 BSI 04-1999 3 1 Scope and object This section of IEC60534-6 is intended to p

22、ermit a variety of positioning devices, which respond to a linear motion, to be mounted on the actuator of a control valve, either directly or by employing an intermediate mounting bracket. This section is applicable where interchangeability between actuators and positioners is desired. The followin

23、g parameters define the intended applicability of this section for the guidance of manufacturers and users. The standardized mounting applies only to positioners which are mounted on the side of the actuator. The standardized mounting applies in general only to actuators which have a travel from10 m

24、m through100 mm. The standardized mounting is designed to cover three basic types of actuator designs (seeFigure 1): a) those with some form of cast or fabricated yoke to connect the actuator power unit to the valve; b) those which use some form of central tube yoke to connect the actuator power uni

25、t to the valve; c) those in which the yoke incorporates two or more columns or pillars to connect the actuator power unit to the valve. 2 Definitions For the purpose of this section of IEC60534-6, the definitions given in the other parts of IEC60534 apply. 3 Basic design principles The objective is

26、to standardize the attachment of the positioner to the side of the actuator to assure compatibility of products from different manufacturers. 3.1 For this purpose, the manufacturer of the actuator shall observe the design criteria described in Figure 1 through Figure 4. Such criteria consist of one

27、or more of the following attachment means provided on the actuator yoke: a) one or more suitable rib(s) with fixing hole(s) (see Figure 1e); b) a plane surface allowing the mounting of the positioner by means of two or more of the four outer threaded holes (see Figure 2c); c) a suitable shape allowi

28、ng the fastening of the mounting plate by means of U-bolts as indicated in Figure 3c. It is recommended that two means of the attachment of the same design be provided on both sides of the yoke in order to allow the reversal of positioner mounting from one side to the other side. However, if the act

29、uator yoke can be turned by180without any change, then one side only attachment means may be provided. 3.2 The design of the positioner mounting shall assure: a) correct positioning of the positioner in relation to the actuator stem; b) rigid mounting of the positioner. 3.3 The manufacturer of the p

30、ositioner may design a positioner incorporating a means of attachment compatible with this standard. Alternatively, a separate mounting plate may be supplied which is compatible with the standardized mounting. 4 Feedback connection In order to standardize the feedback attachment to the actuator, a c

31、onnection piece shall be provided which shall have four threaded holes tapped M6 surrounded with a bearing area of at least10 mm diameter for each hole (see Figure 2). The remaining design of the feedback attachment is not specified and may be designed to meet the requirements of each manufacturer.

32、If the design permits the connection piece to be rotated through180 , only two threaded holes, on one side only, need be provided. The manufacturer of the positioner shall provide adequate means of transmitting the motion of the actuator stem to the positioner by use of the above connection piece. 5

33、 Mounting plate design The positioner shall either incorporate the attachment means for the direct mounting or be provided with a mounting plate in accordance with the details given in Figure 4. It should be noted that only the standardized details are given. Details such as material thickness to pr

34、ovide rigidity and design of mounting means of the, positioner have not been standardized. The design of the mounting plate shall ensure sufficient contact with the rib or plane surface to ensure that the objective of3.2 b) is attained. 6 Actuator yoke mounting The actuator yoke shall be provided wi

35、th one of the following means for mounting the positioner: a) ribs of the cross-section shown in Figure 1e and relative position shown in Figure 1a, Figure 1b and Figure 1c;EN60534-6-1:1997 4 BSI 04-1999 b) two U-bolts as shown in Figure 3c and Figure 5 provided that the diameter of the supporting p

36、illars is between20 mm and35 mm; c) any two of the outer fixing holes in the bracket on a suitable surface. NOTEThe feedback connection is shown at mid-travel of the stem. Figure 1 Dimensions of standardized actuatorsEN60534-6-1:1997 BSI 04-1999 5 NOTEThe feedback connection is shown at mid-travel o

37、f the stem. Figure 1 Dimensions of standardized actuators (continued)EN60534-6-1:1997 6 BSI 04-1999 NOTEThe feedback connection is shown at mid-travel of the stem. Figure 1 Dimensions of standardized actuators (continued)EN60534-6-1:1997 BSI 04-1999 7 Figure 1d Pillar yoke for U-bolt application Fig

38、ure 1 Dimensions of standardized actuators (concluded)EN60534-6-1:1997 8 BSI 04-1999 NOTEThe feedback connection is shown at mid-travel of the stem. Figure 2 Drilling and dimensions for feedback connectionEN60534-6-1:1997 BSI 04-1999 9 NOTEThe feedback connection is shown at mid-travel of the stem.

39、Figure 2 Drilling and dimensions for feedback connection (continued)EN60534-6-1:1997 10 BSI 04-1999 NOTE1The feedback connection is shown at mid-travel of the stem. NOTE2At least two of the four M8 holes shall be on the yoke. Figure 2 Drilling and dimensions for feedback connection (concluded)EN6053

40、4-6-1:1997 BSI 04-1999 11 Figure 3a Attachment on rib Figure 3b Attachment on plane surface Figure 3c Attachment on pillar Figure 3 Mounting plate attachmentsEN60534-6-1:1997 12 BSI 04-1999 NOTEConcave profile to match pillar or rib mounting (see Figure 1d and Figure 1e) Figure 4 Mounting plate dime

41、nsionsEN60534-6-1:1997 BSI 04-1999 13 Figure 5 U-bolt dimensionsBS EN 60534-6-1:1998 IEC 60534-6-1: 1997 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Eu

42、rope and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our produ

43、cts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members a

44、n individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In respon

45、se to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through i

46、ts Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards

47、developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the public

48、ations of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permi

49、ssion from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.