BS EN 60383-1-1998 Insulators for overhead lines with a nominal voltage above 1000 V Ceramic or glass insulator units for a c systems - Definitions test methods and acceptance crit.pdf

《BS EN 60383-1-1998 Insulators for overhead lines with a nominal voltage above 1000 V Ceramic or glass insulator units for a c systems - Definitions test methods and acceptance crit.pdf》由会员分享，可在线阅读，更多相关《BS EN 60383-1-1998 Insulators for overhead lines with a nominal voltage above 1000 V Ceramic or glass insulator units for a c systems - Definitions test methods and acceptance crit.pdf（48页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60383-1:1998 Incorporating Amendment No.1 Insulators for overhead lines with nominal voltage above 1 kV Part 1: Ceramic or glass insulator units for a.c. systems Definitions, test methods and acceptance criteria The European Standard EN60383-1:1996 with the inclusion of amendm

2、ent A11:1999 has the status of a British Standard ICS 29.080.10BS EN 60383-1:1998 This British Standard, having been prepared under the directionof the Electrotechnical Sector Board, was published underthe authority of the Standards Board and comes intoeffect on 15October1998 BSI 02-2001 ISBN 0 580

3、30505 8 National foreword This British Standard is the English language version of EN60383-1:1996 including amendmentA11:1999. It is identical with IEC60383-1:1993. The UK participation in its preparation was entrusted by Technical Committee PEL/36, Insulators for power systems, to Subcommittee PEL/

4、36/2, Line insulators, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European devel

5、opments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From1January1997, all IEC publications have the number60000 added to the old number. For instance, IEC27-1 has been renumbered as IEC60027-1. For a period of t

6、ime during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with thei

7、r corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electr

8、onic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This doc

9、ument comprises a front cover, an inside front cover, theEN title page, pages 2 to 44, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments 10798 February 200

10、1 Removal from annex ZB of the A-deviation for Austria. Correction of date in shoulder heads on pages 2 to 44EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60383-1 November 1996 + A11 October 1999 ICS 01.040.29; 29.080.10 Descriptors: Insulators, overhead lines, ceramic, glass English version

11、Insulators for overhead lines with a nominal voltage above1kVPart 1: Ceramic or glass insulator units for a.c. systemsDefinitions, test methods and acceptance criteria (includes amendment A11:1999) (IEC383-1:1993) Isolateurs pour lignes ariennes de tension nominale suprieure 1 kV Partie 1: Elments d

12、isolateurs en matire cramique ou en verre pour systmes courant alternatif Dfinitions, mthodes dessai et criteres dacceptation (inclut lamendement A11:1999) (CEI 383-1:1993) Isolatoren fr Freileitungen mit einer Nennspannung ber 1 kV Teil 1: Keramik- oder Glas-Isolatoren fr WechselstromsystemeBegriff

13、e, Prfverfahren und Annahmekriterien (enthlt nderung A11:1999) (IEC 383-1:1993) This European Standard was approved by CENELEC on1996-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a

14、national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A versi

15、on in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, Fr

16、ance, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung C

17、entral Secretariat: rue de Stassart 35, B-1050 Brussels 1996 Copyright reserved to CENELEC members Ref. No. EN 60383-1:1996 + A11:1999 EEN 60383-1:1996 BSI 02-2001 2 Foreword The text of the International Standard IEC383-1:1993, prepared by SC36B, Insulators for overhead lines, of IEC TC36, Insulato

18、rs, was submitted to the formal vote and was approved by CENELEC as EN60383-1 on1996-10-01 without any modification. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. Annexes designated “informative” are given for information only. In this standard,

19、Annex ZA is normative and Annex A, Annex B, Annex C and Annex ZB are informative. Annex ZA andAnnex ZB have been added by CENELEC. In the official version, forAnnex C, List of normative documents given for information, the following notes have to be added for the standards indicated: Foreword to ame

20、ndment A11 At the request of the Austrian electrotechnical committee, a draft for an amendment to EN60383-1:1996 was submitted to the CENELEC members for acceptance in July1999. The text of the draft was accepted by CENELEC as amendment A11 to EN60383-1:1996 on 1999-09-27. The following dates were f

21、ixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1997-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1997-06-01 IEC 168 NOTEIEC168:1994 is harmonize

22、d as EN60168:1994 (not modified). IEC 383-2 NOTEHarmonized as EN60383-2:1995 (notmodified). IEC 507 NOTEHarmonized as EN60507:1993 (notmodified). IEC 672-1 NOTEHarmonized as HD426.1 S1:1983, which is superseded by EN 60672-1:1995 (IEC672-1:1995, not modified). IEC 672-3 NOTEHarmonized as HD426.3 S1:

23、1987 (notmodified). ISO 9000 NOTEISO 9000-1:1994 is harmonized as ENISO9000-1:1994 (not modified). ISO 9001 NOTEISO 9001:1994 is harmonized as ENISO9001:1994 (not modified). ISO 9002 NOTEISO 9002:1994 is harmonized as ENISO9002:1994 (not modified). ISO 9003 NOTEISO 9003:1994 is harmonized as ENISO90

24、03:1994 (not modified). ISO 9004 NOTEISO9004-1:1994 is harmonized as ENISO9004-1:1994 (not modified). latest date by which the existence of the amendment has to be announced at national level (doa) 1999-12-27 latest date by which the amendment has to be implemented at national level by publication o

25、f an identical national standard or by endorsement (dop) 2000-03-27EN 60383-1:1996 BSI 02-2001 3 Contents Page Foreword 2 Introduction 7 Section 1. General 1 Scope and object 7 2 Normative references 8 3 Definitions 8 3.1 Insulator string 8 3.2 Pin insulator 8 3.3 Line post insulator 9 3.4 Traction

26、insulator 9 3.5 Lot 9 3.6 Flashover 9 3.7 Dry lightning impulse withstand voltage 9 3.8 50% dry lightning impulse flashover voltage 9 3.9 Wet power-frequency withstand voltage 9 3.10 Electromechanical failing load 9 3.11 Mechanical failing load 9 3.12 Puncture voltage 9 3.13 Creepage distance 9 3.14

27、 Displacements 10 3.15 Short standard string 10 3.16 Specified characteristics 10 Section 2. Insulators 4 Classification, types of insulators and insulating materials 10 4.1 Insulator classes 10 4.2 Insulator types 10 4.3 Insulating materials 10 5 Identification of insulators 11 Section 3. Classific

28、ation of tests, sampling rules and procedures 6 Classification of tests 11 6.1 Type tests 11 6.2 Sample tests 11 6.3 Routine tests 11 7 Quality assurance 12 8 Procedures for type and sample tests 12 8.1 Insulator selection for type tests 12 8.2 Sampling rules and procedures for sample tests 12 8.3 R

29、e-test procedure for sample tests 12 Page Section 4. Test procedures for electrical tests 9 General requirements for high voltage tests 13 10 Standard atmospheric conditions and correction factors for electrical tests 13 10.1 Standard reference atmosphere 13 10.2 Correction factors for atmospheric c

30、onditions 13 11 Artificial rain parameters for wet tests 13 12 Mounting arrangements for electrical tests 14 13 Lightning impulse voltage tests (type test) 14 13.1 Test procedure 14 13.2 Acceptance criteria 14 14 Wet power-frequency voltage tests (type test) 14 14.1 Test procedure 14 14.2 Acceptance

31、 criteria 14 15 Puncture withstand test (sample test, for class B insulators only) 15 15.1 Power-frequency puncture withstand test 15 15.2 Impulse overvoltage puncture withstand test 15 16 Routine electrical test (only on class B insulators of ceramic material or annealed glass) 15 Section 5. Test p

32、rocedures for mechanical and other tests 17 Verification of the dimensions (type and sample test) 16 18 Electromechanical failing load test (type and sample test) 16 18.1 Test procedure 16 18.2 Acceptance criteria 16 19 Mechanical failing load test (type and sample test) 17 19.1 Test procedure for p

33、in and line post insulators 17 19.2 Test procedure for string insulator units 17 19.3 Acceptance criteria for pin insulators 17 19.4 Acceptance criteria for string insulator units and line post insulators 17EN 60383-1:1996 4 BSI 02-2001 Page 20 Thermal-mechanical performance test (type test) 18 20.1

34、 Test procedure 18 20.2 Acceptance criteria 18 21 Verification of the axial, radial and angular displacements (sample test) 18 21.1 Test procedure 18 21.2 Acceptance criteria for cap and pin insulators 19 21.3 Acceptance criteria for long rod insulators 19 22 Verification of the locking system (samp

35、le test) 19 22.1 Conformity of the locking device 19 22.2 Verification of locking 19 22.3 Position of the locking device 20 22.4 Procedure for the operation test 20 22.5 Acceptance criteria for the operation test 20 23 Temperature cycle test (sample test) 20 23.1 Test procedure for string insulator

36、units, pin insulators and line post insulators composed of ceramic material 20 23.2 Test procedure for string insulator units, pin insulators and line post insulators composed of annealed glass 21 23.3 Special test procedure for insulators with thick sections or very large insulators 21 23.4 Complem

37、entary specifications 21 23.5 Acceptance criteria 21 24 Thermal shock test (sample test) 22 24.1 Test procedure 22 24.2 Acceptance criteria 22 25 Porosity test (sample test) 22 25.1 Test procedure 22 25.2 Acceptance criteria 22 26 Galvanizing test (sample test) 22 26.1 Test procedures 22 26.1.1 Appe

38、arance 22 26.1.2 Determination of the coating mass by the magnetic test method 22 26.2 Acceptance criteria. 23 26.2.1 Acceptance criteria for the appearance test 23 Page 26.2.2 Acceptance criteria for the value of coating mass 23 27 Routine visual inspection 23 27.1 Insulators with ceramic insulatin

39、g parts 23 27.2 Insulators with glass insulating parts 24 28 Routine mechanical test 24 28.1 Routine mechanical test on line post insulators 24 28.2 Routine mechanical test on string insulator units 24 Section 6. Pin insulators 29 Mounting arrangements for tests on pin insulators 25 29.1 Standard mo

40、unting arrangement for electrical tests 25 29.2 Mounting arrangements for electrical tests reproducing service conditions 25 29.3 Mounting arrangement for the mechanical failing load test 26 Section 7. Line post insulators 30 Coefficients for statistical analysis of the test results on line post ins

41、ulators 27 30.1 Coefficient for type tests 27 30.2 Coefficients for sample tests 27 31 Mounting arrangements for tests on line post insulators 28 31.1 Standard mounting arrangement for electrical tests 28 31.2 Mounting arrangements for electrical tests reproducing service conditions 29 31.3 Mounting

42、 arrangement for the mechanical failing load test 29 Section 8. String insulator units 32 Prescriptions concerning type tests on string insulators 29 32.1 Electrical type tests on string insulators 29 32.2 Mechanical type tests 30 33 Coefficients for statistical analysis of the test results on strin

43、g insulators 30 33.1 Coefficient for type tests 30 33.2 Coefficients for sample tests 30EN 60383-1:1996 BSI 02-2001 5 Page 34 Mounting arrangements for electrical tests on string insulator units 31 Section 9. Insulators for overhead electric traction lines 35 Mounting arrangements for electrical tes

44、ts on insulators for overhead electric traction lines 33 35.1 Standard mounting arrangement 33 35.2 Mounting arrangement representing service conditions 33 Annex A (informative) Method of comparison of the results of electromechanical or mechanical type and sample tests 36 Annex B (informative) Illu

45、stration of the mechanical and electromechanical test acceptance procedure for string insulator units and line post insulators 37 Annex C (informative) List of normative documents given for information 41 Annex ZA (normative) Normative references to international publications with their correspondin

46、g European publications 43 Annex ZB (informative) A-deviations 44 Figure 1 Schematic representation ofthethermal-mechanical performance test 34 Figure 2 Measurement of axial and radial displacements 34 Figure 3 Measurement of angular displacement 35 Figure 4 Greatest thickness of the insulator 35 Fi

47、gure B.1 Acceptance flow chart for mechanical or electromechanical type tests 37 Figure B.2 Acceptance flow chart for mechanical or electromechanical sample tests 38 Figure B.3 Flow chart of the comparison of type and sample test results 39 Table 1 Cross-reference table for pin insulators 26 Table 2

48、 Cross-reference table for line post insulators 28 Table 3 Cross-reference table for string insulator units 32 Page Table B.1 Examples for mechanical or electromechanical sample tests 40 Table B.2 Blank form for calculation for mechanical or electromechanical sample tests 416 blankEN 60383-1:1996 BS

49、I 02-2001 7 Section 1. General Introduction This part of IEC383 is divided into nine sections. The first five sections cover general clauses, including general requirements and relevant test procedures. Sections 6 to 9 deal with four different types of insulators: Section 6: Pin insulators Section 7: Line post insulators Section 8: String insulator units Section 9: Insulators for overhead electric traction lines. Sections6, 7 and8 begin with a cross-reference table giving the tests applicable to the insulators