BS EN 14135-2004 Coverings - Determination of fire protection ability《覆盖物 防火能力的测定》.pdf

《BS EN 14135-2004 Coverings - Determination of fire protection ability《覆盖物 防火能力的测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 14135-2004 Coverings - Determination of fire protection ability《覆盖物 防火能力的测定》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 14135:2004 Coverings Determination of fire protection ability The European Standard EN 14135:2004 has the status of a British Standard ICS 13.220.50 BS EN 14135:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 15 Oc

2、tober 2004 BSI 15 October 2004 ISBN 0 580 44616 6 National foreword This British Standard is the official English language version of EN 14135:2004. The UK participation in its preparation was entrusted by Technical Committee FSH/22, Fire resistance tests, to Subcommittee FSH/22/7, Test procedures f

3、or partitions and walls, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in t

4、he BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible

5、 for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK

6、interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover. The BSI copyright notice displayed in this document indicates wh

7、en the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN14135 August2004 ICS13.220.50 Englishversion CoveringsDeterminationoffireprotectionability RevtementsDterminationdelacapacitdeprotection contrelincendie Brandsc

8、hutzbekleidungenBestimmungder Brandschutzwirkung ThisEuropeanStandardwasapprovedbyCENon10December2003. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliograph

9、icalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtothe

10、CentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Sloven

11、ia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN14135:2004:EE

12、N 14135:2004 (E) 2 Contents page Foreword. 3 1 Scope 4 2 Normative references . 4 3 Terms and definitions. 4 4 Principle . 5 5 Test equipment5 6 Preparation of test specimen. 5 7 Test procedure 6 8 Expression of test results 6 9 Test report . 7 10 Field of direct application of test results 7 EN 141

13、35:2004 (E) 3 Foreword This document (EN 14135:2004) has been prepared by Technical Committee CEN/TC 127 “Fire safety in buildings”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endo

14、rsement, at the latest by February 2005, and conflicting national standards shall be withdrawn at the latest by February 2005. This European Standard has been prepared under a Mandate given to CEN by the Commission of the European Communities and the European Free Trade Association, and supports ess

15、ential requirements of the Construction Products Directive. Safety warning The attention of all persons concerned with managing and carrying out this test is drawn to the fact that fire testing may be hazardous and that there is a possibility that toxic and/or harmful smoke and gases may be evolved

16、during the test. Operational hazards may also arise during the testing of specimens and the disposal of test residues. An assessment of all potential hazards and risks to health should be made and safety precautions should be identified and provided. Written safety instructions should be issued. App

17、ropriate training should be given to relevant personnel. Laboratory personnel should ensure that they follow written safety instructions at all times. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europe

18、an Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 14135:2004 (

19、E) 4 1 Scope This document specifies a method for determining the ability of a covering to protect underlying products against damage during a specified fire exposure. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated referenc

20、es, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1363-1:1999, Fire resistance tests Part 1: General requirements. EN ISO 13943:2000, Fire safety Vocabulary (ISO 13943:2000). 3 Terms and definitions For th

21、e purposes of this document the terms and definitions given in EN 1363-1:1999, EN ISO 13943:2000 and the following apply. 3.1 covering product which is intended to protect underlying products against damage during a specified fire exposure 3.2 product material, element or component about which infor

22、mation is required 3.3 material basic single substance or a uniformly dispersed mixture of substances, e.g. metal, stone, timber, concrete, mineral wool with dispersed binder, polymers 3.4 damaged material material which has been burnt, charred, melted, shrunk or otherwise visually changed. Discolor

23、ation and soot deposits are not regarded as damage 3.5 burnt material material which has been destroyed by combustion or pyrolysis 3.6 charred material material which has formed carbonaceous residue resulting from pyrolysis or combustion 3.7 melted material material which has melted under the influe

24、nce of heat 3.8 shrunk material material which has become smaller in size EN 14135:2004 (E) 5 3.9 substrate product which is used beneath the product about which information is required 3.10 test specimen covering and substrate provided for the purpose of determining the fire protection ability of t

25、he covering 4 Principle The covering is attached to the lower side of a horizontally orientated substrate and is exposed from below in a furnace in accordance with EN 1363-1 during a specified time stipulated in advance. The temperature rises in the test specimen are recorded. The covering is observ

26、ed and the time when damage is inflicted on it is noted. After the test the damage to both the covering and the substrate is noted. 5 Test equipment 5.1 Horizontal furnace, capable of subjecting the test specimen from below to the heating and pressure conditions specified in EN 1363-1. 5.2 Frame, wi

27、th wooden beams perpendicular to the longest side of the frame (see Figure 1). 5.3 Thermocouples, to be attached between the covering and the substrate, shall be disc thermocouples as specified in EN 1363-1. Each thermocouple junction shall be attached to the centre of the face of a copper disc 12 m

28、m in diameter and 0,2 mm thick. The copper disc shall be directed towards the surface for which the temperature is to be measured. 6 Preparation of test specimen 6.1 The test specimen shall be rectangular with an exposed surface area of at least 6,0 m 2and a minimum side length of 2,40 m. 6.2 Chipbo

29、ard not treated with a fire retardant, with a thickness of (19 2) mm, which is used as a standard substrate, shall be attached to the lower side of the wooden beams of the frame. The chipboard shall have a density of (680 50) kg/m 3at a temperature of (23 2) C and a relative humidity of (50 5) %. Lo

30、w density material substrates (with a density less than 300 kg/m 3 ) and other specific substrates may also be used (see Clause 10). 6.3 On the lower side of the substrate a minimum of eight thermocouples shall be fixed, evenly distributed on the surface (see Figure 1). If possible, none of these ei

31、ght thermocouples shall be fixed closer than 100 mm from any joint between covering elements. Otherwise, the distance between the joints and the thermocouples shall be as large as possible. Each thermocouple shall be held in place using a mechanical fixing arrangement (e.g. staples on the wire). 6.4

32、 If the covering consists of segments, then these shall have the same dimensions as the manufactured product, and at least three segments shall meet each other in at least one point of the test specimen. The joints shall be representative of those used in practice. EN 14135:2004 (E) 6 6.5 The coveri

33、ng shall be mounted and fixed in a manner representative of the way it is applied in practice. The edges of the covering and/or the test specimen shall not be supported in a more secure manner than in practice. 6.6 A covering with an air gap (a cavity) behind it shall be mounted with the same air ga

34、p as in practice, and in addition to the eight thermocouples on the underside of the substrate as specified in 6.3 eight thermocouples shall be mounted on the unexposed surface of the covering (these thermocouples shall be placed immediately below the thermocouples specified in 6.3). 6.7 The test sp

35、ecimen shall be verified as specified in EN 1363-1. 6.8 Prior to testing, the test specimen shall be conditioned in accordance with EN 1363-1. NOTE Figure 1 shows an example of a test specimen with a product where in practice there are joints around the perimeter. Other products, e.g. a plaster, wou

36、ld not require the same position of joints. 7 Test procedure 7.1 Place the test specimen in the horizontal furnace with the covering facing downwards and exposed to the standard heating and pressure conditions specified in EN 1363-1. 7.2 There shall be at least one plate thermometer for every 1,5 m

37、2of the exposed area of the test construction, subject to a minimum of four. The plate thermometers shall be oriented so that side A faces the floor of the furnace. 7.3 During the test, record the temperature rises in the furnace and in the test specimen, and the pressure in the furnace and record t

38、he following observations: time at which cracks, or other damage, occur on the covering; time at which the covering burns with flames or transmits combustible gases which visibly ignite; time at which the covering, or parts of it, falls down or becomes loose so that the lower side of the substrate i

39、s exposed directly to the fire. 7.4 The test is terminated immediately after the specified time (the envisaged classification period). 7.5 Immediately after the test has been terminated, remove the test specimen from the furnace and extinguish any burning in the test specimen. 7.6 After the test, th

40、e following observations shall be recorded: damage to the covering; extent (areas, depths and estimated volume, as appropriate) of any damaged material within the substrate, i.e. material which has been burnt, charred, melted, shrunk or otherwise visually changed. 8 Expression of test results 8.1 Th

41、e time/temperature and the time/pressure plots obtained for the furnace shall be reported. 8.2 The time/temperature plot measured with each individual thermocouple in the test specimen as well as the average curves for these measurements shall be reported. EN 14135:2004 (E) 7 9 Test report The test

42、report shall contain the following information: a) name and address of the testing laboratory; b) date and identification number of the report; c) name and address of the sponsor; d) purpose of the test; e) method of sampling; f) name of manufacturer or supplier of the product; g) name or other iden

43、tification marks of the product; h) density or mass per square unit and thickness of the product; i) date of supply of the product; j) description of the test specimen including all materials used and including a description of how the covering is installed and attached to the substrate together wit

44、h a sketch showing the dimensions of the test specimen (including any covering elements) and the location of the thermocouples for measuring the temperatures in the test specimen; k) conditioning of the test specimen; l) date of test; m) reference to this document; n) test results in accordance with

45、 7.3, 7.6, 8.1 and 8.2; o) any observations made during and after the test and comments on any difficulties experienced during testing. 10 Field of direct application of test results 10.1 Test results obtained with the standard substrate (see 6.2) apply for the covering used on substrates having a d

46、ensity of at least 300 kg/m 3for a covering designated K 1and used on all substrates for a covering designated K 2 . 10.2 When the test has been carried out with a substrate of a low density material (a material with a density less than 300 kg/m 3 ) having a thickness of at least 50 mm, then the res

47、ults apply to any substrate of the same type of material and having a density and/or thickness greater than that tested. 10.3 When the test is carried out with a specific substrate (i.e. a substrate not covered by 10.1 or 10.2), the test results obtained shall be valid only for the covering used on

48、a substrate with composition identical to that used in the test. EN 14135:2004 (E) 8 10.4 Test results obtained for a covering which is mechanically fixed by screws or nails, apply to the tested covering with the same fixing method but at closer spacing between the fixings than in the test specimen. 10.5 Test results obtained for a covering with an air gap (a cavity) behind it also apply to the tested covering with the height of the air gap (the cavity) being greater than the height tested. 10.6 The test results obtained are used not only for horizontal but als