BS EN 3832-2005 Aerospace series - Bolts double hexagon head relieved shank long thread in heat resisting nickel base alloy NI-PH2601 (Inconel 718) - Classification 1550 MPa (at am.pdf

《BS EN 3832-2005 Aerospace series - Bolts double hexagon head relieved shank long thread in heat resisting nickel base alloy NI-PH2601 (Inconel 718) - Classification 1550 MPa (at am.pdf》由会员分享，可在线阅读，更多相关《BS EN 3832-2005 Aerospace series - Bolts double hexagon head relieved shank long thread in heat resisting nickel base alloy NI-PH2601 (Inconel 718) - Classification 1550 MPa (at am.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS EN 3832:2004 Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-PH2601 (Inconel 718) Classification: 1 550 MPa (at ambient temperature) / 650 C The European Standard EN 3832:2004 has the status of a British Standard IC

2、S 49.030.20 BS EN 3832:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 6 January 2005 BSI 6 January 2005 ISBN 0 580 45181 X National foreword This British Standard is the official English language version of EN 3832:2004. It supersedes B

3、S EN 3832:2003 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross

4、-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of B

5、ritish Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; pre

6、sent to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an

7、 inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM E

8、N 3832 November 2004 ICS 49.030.20 Supersedes EN 3832:2003 English version Aerospace series - Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-PH2601 (Inconel 718) - Classification: 1 550 MPa (at ambient temperature) / 650 C Srie arospatiale - Vis tte b

9、ihexagonale, ft dgag, filetage long, en alliage rsistant chaud base de nickel NI-PH2601 (Inconel 718) - Classification : 1 550 MPa ( temprature ambiante) / 650 C Luft- und Raumfahrt - Zwlfkantschrauben, Dnnschaft, langes Gewinde, aus hochwarmfester Nickelbasislegierung NI-PH2601 (Inconel 718) - Klas

10、se: 1 550 MPa (bei Raumtemperatur) / 650 C This European Standard was approved by CEN on 11 September 2003. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterat

11、ion. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translat

12、ion under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hung

13、ary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de

14、 Stassart, 36 B-1050 Brussels 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3832:2004: E EN 3832:2004 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Required characteristics.4 4 Designation 8 5 Marking .8

15、 6 Technical specification .8 EN 3832:2004 (E) 3 Foreword This document (EN 3832:2004) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has re

16、ceived the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2

17、005, and conflicting national standards shall be withdrawn at the latest by May 2005. This document supersedes EN 3832:2003. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belg

18、ium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 3832:2004 (E) 4 1 Scope This standard

19、specifies the characteristics of double hexagon headed bolts, with relieved shank and long thread, in NI-PH2601, for aerospace applications. Classification: 1 550 MPa 1)/ 650 C 2)2 Normative references The following referenced documents are indispensable for the application of this document. For dat

20、ed references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3353-1, Aerospace Lead and runout threads Part 1: Rolled external threads ISO 4095, Aerospace Bihexagonal drives Wrenching configuration Metric

21、 series ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts EN 2424, Aerospace series Marking of aerospace products EN 2952, Aerospace series Heat resisting alloy NI-PH2601 Solution treated and cold worked Bar for forged fasteners D 50 mm 1 270 MPa R m 1 550 MPa 3)EN 3666, A

22、erospace series Heat resisting alloy NI-PH2601 Solution treated and cold worked Bar for forged fasteners D 50 mm 1 550 MPa R m 1 830 MPa 3)EN 3833, Aerospace series Bolts, MJ threads, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), passivated Classification: 1 550 MPa (at ambient temper

23、ature) / 650 C Technical specification 3 Required characteristics 3.1 Configuration Dimensions Tolerances Masses See Figure 1 and Tables 1 and 2. Dimensions and tolerances are in millimetres. 3.2 Materials EN 3666 or EN 2952 with exception of final heat treatment which shall meet EN 3666 (reference

24、heat treatment and relating mechanical properties). 1) Minimum tensile strength of the material at ambient temperature 2) Maximum test temperature of the parts 3) Published as AECMA Prestandard at the date of publication of this standard EN 3832:2004 (E) 5 Key 1 rolled 2 remove sharp edges 0,1 to 0,

25、4. 3 pitch diameter 4 thread 5 marking 6 conforms to ISO 3353-1. 7 shape in this area at manufacturers option aWhen the length of the shank is less than one times the nominal value of the shank diameter D, the run-out is measured at a distance equal to half the actual shank length. bFor bolts having

26、 a shank length less than one times the nominal value of the shank diameter D, and for those threaded to head, the pitch diameter axis shall be used as the datum. Figure 1 Table 1 Thread aD E F G H K Q R 1 S bT U V X Y Z Code Designation 0,13 max. min. min. min. h15 0,5 max. min. min. max. min. max.

27、 min. 050 MJ5x 0,8-4h6h 4,48 9,1 8,3 6,8 1 5,5 3,4 0,5 0,3 7 2 2,9 2,5 3,7 3,2 0,13 060 MJ6x1-4h6h 5,35 10,6 9,8 7,8 1,2 6 4,2 8 2,3 3,2 2,8 4,6 4,1 0,12 0,15 070 MJ7x1-4h6h 6,35 12,1 11,3 8,8 1,4 6,5 5,2 9 2,6 3,7 3,3 5,4 4,9 0,18 080 MJ8x1-4h6h 7,35 13,6 12,8 9,8 1,6 7 6,2 0,7 0,5 10 2,8 4,1 3,7 5

28、,7 5,2 0,003 0,2 100 MJ10x1,25-4h6h 9,19 16,7 15,7 11,8 2 8 7,9 0,8 12 3,1 5,1 4,7 7,2 6,7 0,15 0,25 120 MJ12x1,25-4h6h 11,19 19,9 18,8 13,7 2,4 9,2 9,8 0,9 0,6 14 3,5 6 5,6 8,5 8 0,0025 0,18 0,3 aIn accordance with ISO 5855-2. bBihexagonal wrenching configuration in conformity with ISO 4095 over le

29、ngth T min. EN 3832:2004 (E) 6 Table 2 Thread code 050 060 070 080 100 120 N W Mass aW Mass a W Mass a W Mass a W Mass a W Mass aLength code 0,3 max. min. max. min. max. min. max. min. max. min. max. min. 008 8 3,26 010 10 3,52 5,11 7,19 9,62 012 12 3,78 5,48 7,71 10,32 014 14 4,04 5,85 8,23 11,02 1

30、8,01 016 16 4,29 6,22 8,75 11,71 19,10 29,41 018 18 2,1 1,7 4,55 6,59 9,27 12,41 20,19 31,03 020 20 4 2,5 4,81 2,7 2,2 6,95 9,79 13,11 21,28 32,64 022 22 6 4,5 5,07 4 2,5 7,32 2,7 2,2 10,31 13,81 22,37 34,25 024 24 8 6,5 5,33 6 4,5 7,69 4 2,5 10,83 2,7 2,2 14,51 23,45 35,87 026 26 10 8,5 5,59 8 6,5

31、8,06 6 4,5 11,36 4 2,5 15,20 24,54 37,48 028 28 12 10,5 5,85 10 8,5 8,43 8 6,5 11,88 6 4,5 15,90 3,3 2,7 25,63 39,10 030 30 14 12,5 6,11 12 10,5 8,80 10 8,5 12,40 8 6,5 16,60 4 2,7 26,72 40,71 032 32 16 14,5 6,37 14 12,5 9,17 12 10,5 12,92 10 8,5 17,30 6 4,5 27,81 3,4 2,8 42,32 034 34 18 16,5 6,63 1

32、6 14,5 9,54 14 12,5 13,44 12 10,5 17,99 8 6,5 28,90 4 2,8 43,94 036 36 20 18,5 6,89 18 16,5 9,91 16 14,5 13,96 14 12,5 18,69 10 8,5 29,98 6 4,5 45,55 038 38 22 20,5 7,15 20 18,5 10,28 18 16,5 14,48 16 14,5 19,39 12 10,5 31,07 8 6,5 47,17 040 40 24 22,5 7,40 22 20,5 10,65 20 18,5 15,00 18 16,5 20,09

33、14 12,5 32,16 10 8,5 48,78 042 42 26 24,5 7,66 24 22,5 11,02 22 20,5 15,52 20 18,5 20,78 16 14,5 33,25 12 10,5 50,40 044 44 28 26,5 7,92 26 24,5 11,39 24 22,5 16,04 22 20,5 21,48 18 16,5 34,34 14 12,5 52,01 046 46 30 28,5 8,18 28 26,5 11,76 26 24,5 16,56 24 22,5 22,18 20 18,5 35,43 16 14,5 53,62 048

34、 48 32 30,5 8,44 30 28,5 12,13 28 26,5 17,08 26 24,5 22,88 22 20,5 36,51 18 16,5 55,24 050 50 34 32,5 8,70 32 30,5 12,50 30 28,5 17,60 28 26,5 23,57 24 22,5 37,60 20 18,5 56,85 052 52 36 34,5 8,96 34 32,5 12,87 32 30,5 18,12 30 28,5 24,27 26 24,5 38,69 22 20,5 58,47 054 54 38 36,5 9,22 36 34,5 13,24

35、 34 32,5 18,65 32 30,5 24,97 28 26,5 39,78 24 22,5 60,08 056 56 40 38,5 9,48 38 36,5 13,61 36 34,5 19,17 34 32,5 25,67 30 28,5 40,87 26 24,5 61,69 058 58 42 40,5 9,74 40 38,5 13,98 38 36,5 19,69 36 34,5 26,36 32 30,5 41,96 28 26,5 63,31 060 60 44 42,5 10,00 42 40,5 14,35 40 38,5 20,21 38 36,5 27,06

36、34 32,5 43,04 30 28,5 64,92 062 62 46 44,5 10,26 44 42,5 14,72 42 40,5 20,73 40 38,5 27,76 36 34,5 44,13 32 30,5 66,54 064 64 48 46,5 10,51 46 44,5 15,09 44 42,5 21,25 42 40,5 28,46 38 36,5 45,22 34 32,5 68,15 066 66 50 48,5 10,77 48 46,5 15,46 46 44,5 21,77 44 42,5 29,16 40 38,5 46,31 36 34,5 69,76

37、 068 68 52 50,5 11,03 50 48,5 15,83 48 46,5 22,29 46 44,5 29,85 42 40,5 47,40 38 36,5 71,38 continued EN 3832:2004 (E) 7 Table 2 (concluded) Thread code 050 060 070 080 100 120 N W Mass aW Mass a W Mass a W Mass a W Mass a W Mass aLength code 0,3 max. min. max. min. max. min. max. min. max. min. max

38、. min. 070 70 54 52,5 11,29 52 50,5 16,20 50 48,5 22,81 48 46,5 30,55 44 42,5 48,48 40 38,5 72,99 072 72 54 52,5 16,56 52 50,5 23,33 50 48,5 31,25 46 44,5 49,57 42 40,5 74,61 074 74 56 54,5 16,93 54 52,5 23,85 52 50,5 31,95 48 46,5 50,66 44 42,5 76,22 076 76 58 56,5 17,30 56 54,5 24,37 54 52,5 32,67

39、 50 48,5 51,75 46 44,5 77,83 078 78 60 58,5 17,67 58 56,5 24,89 56 54,5 33,34 52 50,5 52,84 48 46,5 79,45 080 80 62 60,5 18,04 60 58,5 25,41 58 56,5 34,04 54 52,5 53,93 50 48,5 81,06 082 82 64 62,5 18,41 62 60,5 25,94 60 58,5 34,74 56 54,5 55,01 52 50,5 82,68 084 84 66 64,5 18,78 64 62,5 26,46 62 60

40、,5 35,43 58 56,6 56,10 54 52,5 84,29 086 86 66 64,5 26,98 64 62,5 36,13 60 58,5 57,19 56 54,5 85,91 088 88 68 66,5 27,50 66 64,5 36,83 62 60,5 58,28 58 56,5 87,52 090 90 70 68,5 28,02 68 66,5 37,53 64 62,5 59,37 60 58,5 89,13 092 92 72 70,5 28,54 70 68,5 38,22 66 64,5 60,46 62 60,5 90,75 094 94 74 7

41、2,5 29,06 72 70,5 38,92 68 66,5 61,54 64 62,5 92,36 096 96 76 74,5 29,58 74 72,5 39,62 70 68,5 62,63 66 64,5 93,98 098 98 78 76,5 30,10 76 74,5 40,32 72 70,5 63,72 68 66,5 95,59 100 100 78 76,5 41,02 74 72,5 64,81 70 68,5 97,20 104 104 82 80,5 42,41 78 76,5 66,99 74 72,5 100,43 108 108 86 84,5 43,81

42、 82 80,5 69,16 78 76,5 103,66 112 112 90 88,5 45,20 86 84,5 71,34 82 80,5 106,89 116 116 90 88,5 73,51 86 84,5 110,12 120 120 94 92,5 75,69 90 88,5 113,35 124 124 98 96,5 77,87 94 92,5 116,57 128 128 102 100,5 80,04 98 96,5 119,80 132 132 106 104,5 82,22 102 100,5 123,03 136 136 110 108,5 84,40 106

43、104,5 126,26 140 140 114 112,5 86,57 110 108,5 129,49 144 144 114 112,5 132,71 148 148 118 116,5 135,94 152 152 122 120,5 139,17 156 156 126 124,5 142,40 160 160 130 128,5 145,63 164 164 134 132,5 148,86 168 168 138 136,5 152,09 aMass quoted in kg/1 000 parts EN 3832:2004 (E) 8 4 Designation EXAMPLE

44、 Description block BOLT Identity block EN3832-080060 Number of this standard Thread code (see Table 1) Length code (see Table 2) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 5 Marking EN 2424, style A, as indicated on Figure 1. 6 Technical s

45、pecification EN 3833 blankBS EN 3832:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by

46、Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding

47、an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscriber