BS EN 2149-1996 Rivets solid universal head in aluminium alloy 5056A anodized or chromated inch based series《经阳极电镀或铬酸盐处理的5056A型铝合金通用头型实心铆钉 英制系列》.pdf

《BS EN 2149-1996 Rivets solid universal head in aluminium alloy 5056A anodized or chromated inch based series《经阳极电镀或铬酸盐处理的5056A型铝合金通用头型实心铆钉 英制系列》.pdf》由会员分享，可在线阅读，更多相关《BS EN 2149-1996 Rivets solid universal head in aluminium alloy 5056A anodized or chromated inch based series《经阳极电镀或铬酸盐处理的5056A型铝合金通用头型实心铆钉 英制系列》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS EN 2149:1996 Rivets, solid, universal head, in aluminium alloy 5056A, anodized or chromated, inch based series The European Standard EN 2149:1996 has the status of a British Standard ICS 49.040.20BSEN2149:1996 This British Standard, having been prepared under the

2、 directionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes into effect on 15 September 1996 BSI 07-1999 First published February 1992 Second edition August 1996 The following BSI references relate to the work on this standard: Committee reference ACE/

3、12 Draft for comment 95/711798 DC ISBN 0 580 26141 7 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems, upon which the following bodies were represented: Association of Elec

4、tronic, Telecommunications and Business Equipment Industries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companies Amendments issued since publication Amd. No. Date CommentsBSEN2149:1996 BSI 07-1999 i Contents Page Committees responsible Inside front cove

5、r National foreword ii Foreword 2 1 Scope 3 2 Normative references 3 3 Required characteristics 3 4 Designation 6 5 Marking 6 6 Technical specification 6 Figure 1 4 Figure 2 6 Table 1 3 Table 2 4 Table 3 5 Table 4 6 List of references Inside back coverBSEN2149:1996 ii BSI 07-1999 National foreword T

6、his British Standard has been prepared by Technical Committee ACE/12 and is the English language version of EN2149:1996 Aerospace series Rivets, solid, universal head, in aluminium alloy5056A, anodized or chromated, inch based series, published by the European Committee for Standardization (CEN). It

7、 supersedes BSEN2149:1993 which is withdrawn. EN2149:1996 was produced as a result of international discussions in which the United Kingdom took an active part. Cross-references The British Standards corresponding to the European Standards referred to in the text are identical in number and title wi

8、th those given in clause2, with the exception of EN2117, EN2345 and EN2347 for which no corresponding British Standards exist. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Complian

9、ce with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages2to6, an inside back cover and a back cover. This standard has been updated (see copyright date)

10、 and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2149 April 1996 ICS 49.040.20 Supersedes EN 2149:1992 Descriptors: Aircraft industry, full rivet, round head rivet, aluminium alloy,

11、 anodized metal, dimension, designation, marking English version Aerospace series Rivets, solid, universal head, in aluminium alloy5056A, anodized or chromated, inch based series Srie arospatiale Rivets ordinaires, tte ronde aplatie, en alliage daluminium5056A, anodiss ou chromats, srie base inches

12、Luft- und Raumfahrt Vollniete mit Universalkopf, aus Aluminiumlegierung 5056A, anodisiert oder chromatiert, Zoll-Reihe This European Standard was approved by CEN on 1995-12-27. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Eu

13、ropean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (Engli

14、sh, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Fi

15、nland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 B

16、russels 1996 Copyright reserved to CEN members Ref. No. EN2149:1996 EEN2149:1996 BSI 07-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, thi

17、s Standard has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard supersedes EN2149:1992. This European Standard shall be given the status of a national Standard, either

18、by publication of an identical text or by endorsement, at the latest by October 1996, and conflicting national standards shall be withdrawn at the latest by October 1996. According to the CEN/CENELEC Internal Regulations, the national standards, organizations of the following countries are bound to

19、implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom.EN2149:1996 BSI 07-1999 3 1 Scope This standard specifies the characteristics of solid rivet

20、s, universal head, in aluminium alloy5056A, anodized or chromated, inch based series, for maximum operating temperature120 C. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appro

21、priate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the public

22、ation referred to applies. EN 2000, Aerospace series Quality assurance EN aerospace products Approval of the quality system of manufacturers. EN 2101, Aerospace series Chromic acid anodizing of aluminium and wrought aluminium alloys. EN 2117, Aerospace series Aluminium alloy5056A-H32 wire for solid

23、rivets D # 10mm 1) . EN 2284, Aerospace series Sulphuric acid anodizing of aluminium and wrought aluminium alloys. EN 2345, Aluminium and aluminium alloy rivets Technical specification Aerospace series 1) . EN 2424, Aerospace series Marking of aerospace products. EN 2437, Aerospace series Chromate c

24、onversion coatings (yellow) for aluminium and aluminium alloys 2) . 3 Required characteristics 3.1 Configuration Dimensions Masses SeeFigure 1 and Table 2 and Table 3. Dimensions and tolerances are expressed in millimetres and apply after surface treatment. 3.2 Material EN2117 3.3 Surface treatment

25、SeeTable 1. Table 1 1) Published as AECMA Standard at the date of publication of the present standard 2) In preparation at the date of publication of the present standard Nature Code EN 2284B A EN 2437A1 B EN 2101B a Self-colored rivets (hyphen) Green-colored rivets F a For new products, it shall be

26、 replaced by EN2284B.EN2149:1996 4 BSI 07-1999 Table 2 Figure 1 Diameter code D 1 a D 2 D 3 D 4 L 2 L 3 L 4 R 1 R 2 max. min. max. min. max. min. max. min. max. min. 0,08 016 1,65 1,55 3,35 3,05 1,6 1,2 0,7 1,4 2 0,15 024 2,45 2,35 5 4,5 2,4 1,8 1,9 1,6 1 0,8 0,5 2,9 032 3,25 3,15 6,7 6 3,2 2,4 2,6

27、2,3 1,4 1 0,7 3,9 036 3,65 3,55 7,5 6,8 3,6 2,7 2,9 2,5 1,6 1,6 1,1 4,4 040 4,05 3,94 8,3 7,5 4 3 3,2 2,8 1,7 1,2 0,8 4,9 048 4,85 4,73 10 9 4,8 3,6 3,8 3,3 2 2 1,5 1 5,9 056 5,65 5,53 11,7 10,5 5,6 4,2 4,5 3,9 2,4 1,8 1,2 6,8 0,25 064 6,45 6,33 13,3 12,1 6,4 4,8 5,1 4,5 2,7 2,1 1,4 7,8 080 8,03 7,9

28、 16,7 15,1 8 6 6,4 5,6 3,4 2,4 1,6 9,8 096 9,63 9,5 20 18,1 9,6 7,2 7,7 6,7 4,1 3 2 11,7 a D 1max. may increase by0,03, over length L 3 . + 0,2 0EN 2149:1996 BSI 07-1999 5 Table 3 Diameter code 016 024 032 036 040 048 056 064 080 096 Length Mass b a Mass b a Mass b a Mass b a Mass b a Mass b a Mass

29、b a Mass b a Mass b a Mass b Code L 1 + 0,5 0 N R N R N R N R N R N R N R N R N R 003 3 0,030 004 4 0,036 0,083 0,176 0,227 005 5 0,041 0,095 0,198 0,254 006 6 0,046 0,107 0,220 0,280 0,373 007 7 0,052 0,119 0,242 0,306 0,408 008 8 0,057 0,131 0,264 0,332 0,443 0,664 009 9 0,063 0,143 0,286 0,358 0,

30、478 0,714 010 10 0,068 0,155 0,308 0,384 0,513 0,764 1,137 1,556 011 11 0,074 0,167 0,330 0,410 0,548 0,814 1,205 1,645 012 12 0,079 0,179 0,352 0,436 0,583 0,864 1,273 1,734 013 13 0,085 0,191 0,374 0,462 0,618 0,914 1,341 1,823 3,127 014 14 0,090 0,203 0,396 0,488 0,653 0,964 1,409 1,912 3,266 015

31、 15 0,096 0,215 0,418 0,515 0,688 1,014 1,477 2,001 3,405 016 16 0,101 0,227 0,440 0,541 0,723 1,064 1,545 2,090 3,544 017 17 0,239 0,462 0,567 0,758 1,114 1,613 2,179 3,683 5,669 018 18 0,251 0,484 0,593 0,793 1,164 1,681 2,268 3,822 5,868 019 19 0,263 0,506 0,619 0,828 1,214 1,748 2,357 3,961 6,06

32、7 020 20 0,275 0,528 0,645 0,863 1,264 1,817 2,446 4,100 6,266 022 22 0,299 0,572 0,697 0,933 1,364 1,953 2,624 4,378 6,664 024 24 0,323 0,616 0,749 1,003 1,464 2,089 2,802 4,656 7,062 026 26 0,347 0,660 0,802 1,073 1,564 2,225 2,980 4,934 7,460 028 28 0,371 0,704 0,854 1,143 1,664 2,361 3,158 5,212

33、 7,858 030 30 0,395 0,748 0,906 1,213 1,764 2,497 3,336 5,490 8,256 032 32 0,419 0,792 0,958 1,283 1,864 2,633 3,514 5,768 8,654 035 35 0,455 0,858 1,037 1,388 2,014 2,837 3,781 6,185 9,251 040 40 0,968 1,167 1,563 2,264 3,177 4,226 6,880 10,246 045 45 1,298 1,738 2,514 3,517 4,671 7,575 11,241 050

34、50 1,913 2,764 3,857 5,116 8,270 12,236 055 55 3,014 4,197 5,561 8,965 13,231 060 60 3,264 4,537 6,006 9,660 14,226 a Tail end code (seeFigure 1) b Approximate values (kg/1000 pieces), calculated on the basis of2,76kg/dm 3 , given for information purposes onlyEN2149:1996 6 BSI 07-1999 4 Designation

35、EXAMPLE: NOTEIf necessary, the code19005 shall be placed between the description block and the identity block. 5 Marking 5.1 Rivet EN2424, style G 5.2 Material SeeFigure 2 and Table 4. Table 4 6 Technical specification EN2345 plus EN2000 for the approval of manufacturers Figure 2 Diameter code 016 0

36、24 032 036 040 048 056 064 080 096 T 0,05 0,13 0,15 0,2 S max. 0,8 D 5max. = D 1max. (see Table 2.)BSEN2149:1996 BSI 07-1999 List of references See national foreword.BS EN 2149:1996 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsib

37、le for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments o

38、r editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on t

39、he inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should b

40、e addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide ran

41、ge of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fa

42、x:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in

43、 all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means

44、electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.