BS 4602-1977 Specification for the use of metric units in specifications for glass containers and finishes《玻璃容器及精度公制单位规格使用规范》.pdf

《BS 4602-1977 Specification for the use of metric units in specifications for glass containers and finishes《玻璃容器及精度公制单位规格使用规范》.pdf》由会员分享，可在线阅读，更多相关《BS 4602-1977 Specification for the use of metric units in specifications for glass containers and finishes《玻璃容器及精度公制单位规格使用规范》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 4602:1977 Incorporating Amendment No. 1 Specification for The use of metric units in specifications for glass containers and finishes UDC 621.798.147:666.17:389.151BS4602:1977 This British Standard, having been prepared under the directionof the Packaging andFreight Containers St

2、andardsCommittee, was published under the authority ofthe Executive Board on 29 April 1977 BSI 10-1999 First published April 1970 First revision April 1977 The following BSI references relate to the work on this standard: Committee reference PKM/563 Draft for comment 74/62650DC ISBN 0 580 09981 4 Co

3、operating organizations The Packaging and Freight Containers Standards Committee, under whose supervision this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations: Association of Drum Manufacturers British P

4、aper and Board Industry Federation (PIF) British Paper Bag Federation British Tin Box Manufacturers Federation Chemical Industries Association* Collapsible Tube Manufacturers Association Confederation of British Industry Crown Agents for Oversea Governments and Administrations Department of the Envi

5、ronment Fibreboard Packing Case Manufacturers Association Food Manufacturers Federation Incorporated* Glass Manufacturers Federation* Institute of Packaging Institute of Trading Standards Administration* Ministry of Defence* Oil Companies Materials Association Paintmakers Association of Great Britai

6、n Limited (Pira) Research Association for the Paper and Board Printing and Packaging Industries* Soap and Detergent Industry Association Society of Motor Manufacturers and Traders Limited Timber Packaging and Pallet Confederation The organizations marked with an asterisk in the above list, together

7、with the following, were directly represented on the committee entrusted with the preparation of this British Standard: Association of the British Pharmaceutical Industry British Photographic Manufacturers Association British Soft Drinks Council British Tin Box Manufacturers Federation (Closures) Ca

8、mpden Food Preservation Research Association Dairy Trade Federation Department of Health and Social Security Department of Prices and Consumer Protection Fruit and Vegetable Canners Association Honey Importers and Packers Association National Association of Cider Makers National Association of Soft

9、Drinks Manufacturers Limited Scotch Whisky Association Scottish Association of Soft Drinks Manufacturers Wine and Spirit Association of Great Britain Amendments issued since publication Amd. No. Date of issue Comments 4305 September 1983 Indicated by a sideline in the marginBS4602:1977 BSI 10-1999 i

10、 Contents Page Cooperating organizations Inside front cover Foreword ii 1 Scope 1 2 Dimensions and tolerances 1 3 Capacities and tolerances 1 4 Mass 1 5 Pressure 1 6 Temperature 1 7 Vertical and horizontal loads 1BS4602:1977 ii BSI 10-1999 Foreword This British Standard, prepared under the authority

11、 of the Packaging and Freight Containers Standards Committee at the request of the Glass Manufacturers Federation, was first published in 1970 and revised in 1977. Amendment No. 1 to the second edition has been published to continue to ensure maximum harmonization with general European practice in t

12、his field. The standard provides guidance on the application of metric units for glass manufacturers, their customers and other interested parties concerned with standards for glass containers and finishes and is intended to give uniformity to the preparation and publication of glass container and f

13、inish specifications in metric units. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Sum

14、mary of pages This document comprises a front cover, an inside front cover, pages i and ii, page1and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS4602:1977 BSI 10-

15、1999 1 1 Scope This British Standard specifies the way in which units and tolerances for dimensions, capacity, vertical and horizontal loads and mass of glass containers including their finishes shall be expressed. The units for pressure and temperature are also given. In certain cases, such as for

16、very small containers, finer limits of expression may be required than those given in this standard. Alternatively, for large containers, the limits given may be unnecessarily precise. In such extreme instances, users are advised to consult with their suppliers. Specifications shall, wherever releva

17、nt, carry a covering note to the effect that all dimensions are in millimetres (mm), capacity in litres and/or millilitres (l and/or ml) and mass in grams (g). 2 Dimensions and tolerances 1) 2.1 Body specification 2.1.1 Dimensions (other than radii). Dimensions and their tolerances shall be given to

18、 one place of decimals. 2.1.2 Radii. Wherever practicable, radii shall be given to the nearest whole number only. In some cases, for calculation purposes, it may be necessary to express the dimensions to one place of decimals, e.g.1.3 R. NOTEThe letter R is used as a suffix in order to avoid confusi

19、on with established types of screw thread where the letter R is used as a prefix, e.g. R3, R4 etc. 2.1.3 Plane angles. Plane angles shall be stated in degrees to the nearest degree. 2.1.4 Height. Height shall be given to one decimal place. 2.2 Finish specification 2.2.1 Dimensions (other than radii)

20、. Dimensions and their tolerances shall be given to an accuracy of0.05. 2.2.2 Radii. Radii shall be given to one decimal place except for defining thread contours where an accuracy of0.01may be necessary, e.g.0.86R. 2.2.3 Pitch. Pitch shall be given to an accuracy of0.01. 2.2.4 Plane angles. Plane a

21、ngles shall be stated to the nearest degree. 2.2.5 Helix angles. Helix angles shall be stated in degrees and minutes to the nearest minute. 3 Capacities and tolerances 1) For containers of capacities of1litre and over the capacities shall be stated in litres to two decimal places, e.g.1.23 l. The to

22、lerances shall be stated in millilitres to one decimal place. For containers of capacities below1litre the capacities and their tolerances shall be stated in millilitres to one decimal place. 4 Mass 1) Mass shall be expressed to the nearest gram. 5 Pressure Pressure shall be expressed in bars to the

23、 first decimal place. Since existing equipment for measuring internal resistance pressures is usually graduated in other units, e.g. pounds-force per square inch, pressures may continue to be measured in those units and shall be converted to bars using the following information. 6 Temperature Temper

24、ature shall be expressed in degrees Celsius, to the nearest whole number, e.g.25 C. 7 Vertical and horizontal loads Vertical and horizontal loads shall be expressed in newtons (1 newton (N) is equivalent to 0.225 lbf). 1) See also the final paragraph ofclause1. 1 lbf/in 2(psi) = 6.895 10 2bar 1 atmo

25、sphere (atm) = 1.013 bar 1 kgf/cm 2 = 0.981 bar 1 pascal (Pa) = 1 N/m 2= 1 10 5barBS 4602:1977 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and a

26、t the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and se

27、rvices. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individu

28、al updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orde

29、rs for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library

30、 and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developmen

31、ts and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of

32、the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from

33、 BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.