BS 4185-2-1967 Machine tool components - Collars《机床零件 第2部分 安装环》.pdf

《BS 4185-2-1967 Machine tool components - Collars《机床零件 第2部分 安装环》.pdf》由会员分享，可在线阅读，更多相关《BS 4185-2-1967 Machine tool components - Collars《机床零件 第2部分 安装环》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 4185-2: 1967 Incorporating Amendment No. 1 Specification for Machine tool components Part 2: CollarsBS4185-2:1967 This British Standard, having been approved by the MechanicalEngineering IndustryStandards Committeeand endorsed by theChairman ofthe EngineeringDivisional Council,wa

2、s published undertheauthority of the GeneralCouncil on 31 July 1967 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference MEE/6 Draft for comment D65/8569 ISBN 0 580 34082 1 Co-operating organizations The Mechanical Engineering Industry Standards Committee

3、, under whose supervision this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations: The Government departments and scientific and industrial organizations marked with an asterisk in the above list, together

4、with the following, were directly represented on the committee entrusted with the preparation of this British Standard: Associated Offices Technical Committee Institution of Gas Engineers Association of Consulting Engineers Institution of Heating and Ventilating Association of Mining Electrical and

5、Engineers Mechanical Engineers Institution of Mechanical Engineers* Board of Trade Institution of Mechanical Engineers British Chemical Plant Manufacturers (Automobile Division) Association Institution of Production Engineers* British Compressed Air Society Locomotive and Allied Manufacturers Britis

6、h Electrical and Allied Manufacturers Association of Great Britain Association London Transport Board British Gear Manufacturers Association Machine Tool Trades Association* British Internal Combustion Engine Ministry of Defence Manufacturers Association Ministry of Labour (H.M. Factory British Iron

7、 and Steel Federation Inspectorate) British Mechanical Engineering Federation Ministry of Power British Pump Manufacturers Association Ministry of Public Building and Works* Crown Agents for Oversea Governments and Ministry of Technology National Administrations Engineering Laboratory* Electricity C

8、ouncil, the Central Electricity Ministry of Transport Generating Board and the Area Boards in National Coal Board England and Wales National Physical Laboratory (Ministry of Engineering Equipment Users Association Technology) Gas Council Radio Industry Council Institute of Marine Engineers Royal Ins

9、titute of British Architects Institution of Civil Engineers Association of Supervisory Staffs, Executives National Federation of Engineers Tool and Technicians Manufacturers Ministry of Defence, Air Force Department Production Engineering Research Association Ministry of Defence, Army Department Soc

10、iety of Motor Manufacturers and Traders Ministry of Defence, Navy Department Limited Trades Union Congress Amendments issued since publication Amd. No. Date of issue Comments 1564 September 1974 Indicated by a sideline in the marginBS4185-2:1967 BSI 12-1999 i Contents Page Co-operating organizations

11、 Inside front cover Foreword ii 1 Scope 1 2 Material 1 3 Constructional requirements 1 4 Finish 1 5 Designation 1 6 Marking 1 Figure 1 Collar 2 Table 1 Millimetre dimensions of collars 3 Table 2 Inch dimensions of collars 5BS4185-2:1967 ii BSI 12-1999 Foreword This standard makes reference to the fo

12、llowing British Standards: BS 46, Keys and keyways and taper pins. Part 3: Solid and split taper pins. BS 308, Engineering drawing practice. BS 970, Wrought steels in the form of blooms, billets, bars and forgings. Part 1: Carbon and carbon manganese steels including free cutting steels. BS 1134, Ce

13、ntre-line-average height method for the assessment of surface texture. BS 1580, Unified screw threads. BS 1916, Limits and fits for engineering. Part 1: Limits and tolerances. BS 2470, Hexagon socket screws and wrench keys. BS 3643, ISO metric screw threads. This standard is based on a proposal made

14、 by the Machine Tool Trades Association and is one of a series dealing with components of machine tools. Others in this series are: The specification provides for the collar to be locked by a hexagon socket set screw and for a pilot hole to be drilled with a view to it being additionally locked, at

15、the discretion of the user, by a parallel pin, a taper pin or a second hexagon socket set screw. The size of an appropriate taper pin is given for guidance only. A marking requirement has been included in the standard so that a standard collar may be distinguished from a special and its size readily

16、 identified. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Part 1: Locknuts (“C” Type,

17、socket set screw locking); Part 3: Rolling bearing end caps and retaining plates; Part 4: Shaft spacers; in course of preparation Part: Locknuts for use with tab washers. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1to10, an inside back cover and

18、 a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS4185-2:1967 BSI 12-1999 1 1 Scope This standard relates to separate millimetre and inch series of collars for use in

19、machine tools and their auxiliary equipment. The millimetre series is suitable for shafts6100mm diameter and the inch series for shafts 1 / 4 4 in diameter. NOTEAll the millimetre dimensions in this specification relate to the millimetre series and all the inch dimensions to the inch series. 2 Mater

20、ial Collars shall be manufactured of steel220M07 conforming to BS970-1 1)or from a similar material having equivalent mechanical properties. 3 Constructional requirements 3.1 Dimensions. Collars of the millimetre series shall conform to the dimensions inFigure 1 andTable 1 and those of the inch seri

21、es to those inFigure 1 andTable 2. When plating is specified, the collar shall conform, after plating, to the dimensions given in this standard. 3.2 Collar body. The tolerance on the squareness 2)of the abutment face of the collar (Face X,Figure 1) with respect to the bore A shall be as follows: The

22、 out-of-roundness of the outer cylindrical surface of the locknut and its error of concentricity with respect to the bore A shall be contained within a full indicator movement of0.1mm or0.005in. The thread of the hole for the locking screw shall conform to BS3643 3)and shall be Class6H (millimetre s

23、eries) or to BS1580 4)and be Class2B (inch series). 3.3 Locking screw. The locking screw shall be a hexagon socket set screw with cup point. For the millimetre series, it shall have a thread conforming to BS3643 3) , Class6G; for the inch series it shall conform toBS2470 5)(unified fine thread). The

24、 locking screw shall be designed to be self-locking and to be unaffected by vibration. 4 Finish The abutment face of the collar (Face X,Figure 1) and the bore A shall have a surface texture 6)of0.8m CLA (millimetre series) or32CLA (inch series). The remainder of the collar shall have a surface textu

25、re of 3.2m CLA (millimetre series) or125CLA (inch series). The collar shall be sound and free from burrs, sharp edges and other defects. 5 Designation Collars conforming to this standard shall be designated by the bore diameter and the number of this standard,e.g.collars of nominal bore diameter40mm

26、 and 1 1 / 2in shall be designated: Collar40BS4185-2 Collar1 1 / 2BS4185-2 This designation shall mean the collar complete with hexagon socket set screw and with pilot hole drilled for taper pin, but not including the taper pin. 6 Marking Collars conforming to this standard shall be marked by the ma

27、nufacturer with the bore diameter and the number of this standard,e.g.collars of nominal diameter40mm and1 1 / 2in shall be marked: 40 BS4185-2 1 1 / 2BS4185-2 NOTESee note on the inside back cover about the BSICertification Mark Scheme. 1) BS970, “Wrought steels in the form of blooms, billets, bars

28、 and forgings. Part 1: Carbon and carbon manganese steels including free cutting steels.” 2) See BS308, “Engineering drawing practice”. 1) Millimetre series Up to 50 mm nominal bore 0.02 mm Over 50 mm up to and including 80 mm 0.04 mm Over 80 mm 0.05 mm 2) Inch series Up to 2 in nominal bore 0.001 i

29、n Over 2 in up to and including 3 1 / 4in 0.0015 in Over 3 1 / 4in 0.002 in 3) BS3643, “ISO metric screw threads”. 4) BS1580, “Unified screw threads”. 5) BS 2470,“Hexagon socket screws and wrench keys”. 6) See BS1134, “Centre-line-average height method for the assessment of surface texture”.BS 4185-

30、2:1967 2 BSI 12-1999 Figure 1 CollarBS4185-2:1967 BSI 12-1999 3 Table 1 Millimetre dimensions of collars All dimensions in millimeters. (See Figure 1.) 1 2 3 4 5 Bore diameter A Outside diameter B Length C Nominal Tolerance H7 a Nominal Tolerance h14 a + 0 0.25 6 +0.012 0 16 +0 0.43 8 7 +0.015 0 8 9

31、 20 +0 0.52 10 10 12 +0.018 0 25 12 15 28 17 14 20 +0.021 0 32 +0 0.62 22 25 40 16 28 45 30 32 +0.025 0 55 +0 0.74 18 35 40 65 20 45 70 50 80 55 +0.030 0 60 90 +0 0.87 22 65 100 70 75 110 80 85 +0.035 0 125 +0 1 25 90 95 140 100 a See BS 1916, “Limits and fits for engineering”, Part 1, “Limits and t

32、olerances”.BS4185-2:1967 4 BSI 12-1999 Table 1 Millimetre dimensions of collars All dimensions in millimetres. (See Figure 1.) 6 7 8 9 10 11 12 Chamfer Socket set screw J a Taper pin pilot hole diameter Recommended taper pin Bore diameter A D 1 D 2 H Thread and length Small end diameter Length Nomin

33、al 0.3 1 M4 5 1.3 1.5 18 6 7 8 M6 8 2.8 3 24 9 10 28 12 3.8 4 32 15 17 5.8 6 36 20 22 M8 10 45 25 50 28 30 0.5 2 7.8 8 60 32 35 M10 12 70 40 45 9.8 10 90 50 M10 15 55 100 60 110 65 70 M12 15 120 75 80 M12 20 11.8 12 130 85 90 150 95 100 a See3.3.BS4185-2:1967 BSI 12-1999 5 Table 2 Inch dimensions of

34、 collars All dimensions in inches. (SeeFigure 1.) 1 2 3 4 5 Bore diameter A Outside diameter B Length C Nominal Tolerance H7 a Nominal Tolerance h14 a + 0 0.010 1 / 4 +0.0006 0 5 / 8 +0 0.016 5 / 16 5 / 16 11 / 16 3 / 8 3 / 4 +0 0.020 3 / 8 7 / 16 b +0.0007 0 7 / 8 7 / 16 1 / 2 1 9 / 16 b 1 / 2 5 /

35、8 1 1 / 8 11 / 16 b 1 1 / 4 +0 0.025 9 / 16 3 / 4 +0.0008 0 13 / 16 b 1 3 / 8 1 1 / 2 7 / 8 15 / 16 b 1 5 / 8 5 / 8 1 1 1 / 8 1 3 / 4 1 1 / 4 +0.001 0 2 +0 0.030 3 / 4 1 3 / 8 2 1 / 8 1 1 / 2 2 1 / 4 1 5 / 8 2 1 / 2 a See BS 1916, “Limits and fits for engineering”, Part 1, “Limits and tolerances”. b

36、 Non-preferred.BS4185-2:1967 6 BSI 12-1999 Table 2 Inch dimensions of collars All dimensions in inches. (SeeFigure 1.) 6 7 8 9 10 11 12 Chamfer Socket set screw J a Taper pin pilot hole diameter Recommended taper pin b Bore diameter A D 1 D 2 H Thread length Large end diameter Length Nominal 1 / 64

37、1 / 32 1032 UNF 3 / 16 3 / 64 1 / 16 3 / 4 1 / 4 1 / 16 5 / 64 5 / 16 3 / 32 7 / 8 3 / 8 1 / 4 28 UNF 1 / 4 3 / 32 1 / 8 1 7 / 16 c 3 / 64 1 1 / 4 1 / 2 1 / 8 5 / 32 9 / 16 c 5 / 8 5 / 16 24 UNF 1 / 4 5 / 32 3 / 16 1 1 / 2 11 / 16 c 3 / 4 1 / 16 13 / 16 c 5 / 16 24 UNF 5 / 16 1 3 / 4 7 / 8 11 / 64 7

38、 / 32 15 / 16 c 1 2 1 1 / 8 3 / 8 24 UNF 3 / 8 3 / 16 1 / 4 1 1 / 4 1 / 32 3 / 32 2 1 / 4 1 3 / 8 2 1 / 2 1 1 / 2 15 / 64 5 / 16 2 3 / 4 1 5 / 8 a See3.3. b BS 46, “Keys and keyways and taper pins”, Part 3, “Solid and split taper pins”. c Non-preferred.BS4185-2:1967 BSI 12-1999 7 Table 2 Inch dimens

39、ions of collars All dimensions in inches. (SeeFigure 1.) 1 2 3 4 5 Bore diameter A Outside diameter B Length C Nominal Tolerance H7 a Nominal Tolerance h14 a + 0 0.010 1 3 / 4 +0.001 0 2 3 / 4 +0 0.030 7 / 8 1 7 / 8 3 2 +0.0012 0 2 1 / 8 3 1 / 4 +0 0.035 2 1 / 4 1 2 3 / 8 3 1 / 2 2 1 / 2 2 5 / 8 3 3

40、 / 4 1 1 / 8 2 3 / 4 4 2 7 / 8 4 1 / 4 3 3 1 / 4 +0.0014 0 4 1 / 2 1 1 / 4 3 3 / 8 4 3 / 4 +0 0.040 3 1 / 2 3 3 / 4 5 4 5 1 / 4 a See BS 1916, “Limits and fits for engineering”, Part 1, “Limits and tolerances”.BS4185-2:1967 8 BSI 12-1999 Table 2 Inch dimensions of collars All dimensions in inches. (

41、SeeFigure 1.) 6 7 8 9 10 11 12 Chamfer Socket set screw J a Taper pin pilot hole diameter Recommended taper pin b Bore diameter A D 1 D 2 H Thread length Large end diameter Length Nominal 1 / 32 3 / 32 1 / 2 20 UNF 1 / 2 15 / 64 5 / 16 3 1 3 / 4 3 1 / 4 1 7 / 8 9 / 32 2 3 1 / 2 2 1 / 8 2 1 / 4 3 / 8

42、 3 3 / 4 2 3 / 8 2 1 / 2 1 / 8 17 / 64 4 2 5 / 8 1 / 2 20 UNF 5 / 8 4 1 / 2 2 3 / 4 2 7 / 8 3 5 / 16 7 / 16 5 3 1 / 4 3 3 / 8 3 1 / 2 5 1 / 2 c 3 3 / 4 4 a BS 2470, “Hexagon socket screws and wrench keys”. (With UNF thread.) b BS 46, “Keys and keyways and taper pins”, Part 3, “Solid and split taper

43、pins”. c Non-preferred length.9 blankBS4185-2:1967 BSI 12-1999 10 British Standards The following are available on application: YEARBOOK Including subject index and numerical list of British Standards 15s. SECTIONAL LISTS. Gratis Acoustics Aerospace materials and components Automobile Building mater

44、ials and components Chemical engineering Chemicals, fats, oils, scientific apparatus, etc. Cinematography and photography Coal, coke and colliery requisites Codes of Practice Consumer goods Documentation, including Universal Decimal Classification Drawing practice Electrical engineering Farming, dai

45、rying and allied interests Furniture, bedding and furnishings Gardening, horticulture and landscape work Gas and solid fuel and refractories Glassware including scientific apparatus Hospital equipment Illumination and lighting fittings Industrial instruments, etc. Iron and steel Leather, Plastics, R

46、ubber Machine tools Mechanical engineering Nomenclature, symbols and abbreviations Non-ferrous metals Nuclear energy Packaging and containers Paints, varnishes, paint materials and colours for paints Personal safety equipment Petroleum industry Printing, paper and stationery Road engineering Shipbui

47、lding Textiles and clothing WeldingBS4185-2:1967 BSI 12-1999 NOTEThe mark BS4185 on or in relation to the product is a claim by the manufacturer that it complies with the requirements of the standard. The British Standards Institution is the owner of a registered certification trade mark. This is sh

48、own below, enclosed in the words “Approved to British Standard”. This mark can be used only by manufacturers licensed under the certification mark scheme operated by the BSI. The presence of this mark on or in relation to a product is an assurance that the goods have been produced to comply with the

49、 requirements of the British Standard under a system of supervision, control and testing operated during manufacture and including periodical inspection at the manufacturers works in accordance with the certification mark scheme of the BSI. Further particulars of the terms of licence may be obtained from the Director, British Standards Institution, 2 Park Street, London, W.1.BS 4185-2: 1967 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandar