BS 3900-C1-1965 Methods of test for paints - Tests associated with paint film formation - Wet edge time《涂料试验方法 涂料膜形成试验 湿边时间》.pdf

《BS 3900-C1-1965 Methods of test for paints - Tests associated with paint film formation - Wet edge time《涂料试验方法 涂料膜形成试验 湿边时间》.pdf》由会员分享，可在线阅读，更多相关《BS 3900-C1-1965 Methods of test for paints - Tests associated with paint film formation - Wet edge time《涂料试验方法 涂料膜形成试验 湿边时间》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS3900-C1: 1965 Incorporating Amendment Nos.1 and 2 Methods of Test for Paints Part C1: Wet edge time It is recommended that this Part be read in conjunction with the general information in the Introduction to BS3900 issued separately. UDC667.61+667.612.6BS3900-C1:1965 BSI 10-1999 I

2、SBN 0 580 35631 0 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This d

3、ocument comprises a front cover, an inside front cover, pages i and ii, page1 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication A

4、md. No. Date of issue Comments 724 April 1971 6807 November 1991 Indicated by a sideline in the marginBS3900-C1:1965 BSI 10-1999 i Contents Page 1 Scope 1 2 Supplementary information 1 3 Preparation of coated test panel 1 4 Procedure 1 5 Report of test 1ii blankBS3900-C1:1965 BSI 10-1999 1 NOTEPart

5、C1 is based on DEF-1053 Method No.16, “Settingtime”. 1 Scope 1.1 This Part describes a procedure for determining whether the edge of a film of paint or allied material remains “alive” after a specified period of drying, when applied over the appropriate surface. NOTEThe term “wet edge time” is also

6、known in the paint industry as “lapping time”, “live edge time” and “setting time”. 2 Supplementary information 2.1 The method of test described below requires to be completed, for any particular application, by the following supplementary information. This information is to be derived from the Brit

7、ish Standard or other specification for the material under test or, where appropriate, is to be the subject of agreement between purchaser and vendor. 1) Thickness and/or weight of coating and whether it is to be a single film or a coating system. 2) Wet edge time specified for the material under te

8、st. 3 Preparation of coated test panel 3.1 Unless otherwise stated use a panel of burnished steel, approximately600mm 300mm. 3.2 Prepare the panel in accordance with the method described in Part A3, “Preparation of panels prior to painting” coat it where necessary with the appropriate primer and/or

9、undercoat and allow each coat to dry for24 hours, unless otherwise specified. 4 Procedure 4.1 Carry out the test under substantially draught-free conditions, at a temperature of23 2 C and a relative humidity of50 5%. 4.2 Divide the panel into two equal areas by means of a line parallel to the shorte

10、r side. Place the panel in a position such that the longer side is vertical. 4.3 Coat the upper half of the panel with the material under test, using a25 mm brush. Lay off in a direction parallel to the shorter side and finish laying off along the edge flanking the dividing line taking care to avoid

11、 leaving an abnormally thick or thin edge. 4.4 Invert the panel. 4.5 Approximately2 minutes prior to the specified wet edge time, commence to coat the remaining area so that the two edges are worked together starting at the specified wet edge time, cross-brushing across the join as necessary. 4.6 Fi

12、nally lay off the portion of the panel just coated in a direction parallel to the dividing line, starting at the area disturbed by the join, and allow the panel to dry in situ. 4.7 Examine the join for imperfections, such as lack of film continuity, absence of levelling, variation in colour. 5 Repor

13、t of test 5.1 The test report shall contain at least the following information: 1) Identification of material under test. 2) The British Standard, product specification or other document setting out the supplementary information required for the test (see Clause2 above). 3) Any deviation, by agreeme

14、nt or otherwise, from the standard test procedure. 4) The nature and degree of any imperfection resulting at the join.BS3900-C1: 1965 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents t

15、he UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to imp

16、rove the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:0208

17、9967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:0208996900

18、1. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and inte

19、rnational standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are ke

20、pt up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyri

21、ght, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwis

22、e without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.