BS 1702-1950 Specification for mild steel drums (heavy duty - fixed ends)《中碳钢圆筒规范(重型 端盖固定的)》.pdf

《BS 1702-1950 Specification for mild steel drums (heavy duty - fixed ends)《中碳钢圆筒规范(重型 端盖固定的)》.pdf》由会员分享，可在线阅读，更多相关《BS 1702-1950 Specification for mild steel drums (heavy duty - fixed ends)《中碳钢圆筒规范(重型 端盖固定的)》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS1702:1950 Incorporating Amendment No.1 Specification for Mild steel drums (Heavy DutyFixed Ends)BS1702:1950 This British Standard, having been approved by the PackagingStandards Committee,was published underthe authority of the GeneralCouncil on 30December1950 BSI11-1999 This Brit

2、ish Standard first published in1950supersedes: BS670 First published April1936 BS829 First published February1939 ISBN 0 580 01598 X Co-operating organizations The Packaging Standards Committee, under whose supervision this British Standard was prepared, consists of representatives from the followin

3、g Government departments and scientific and industrial organizations: Association of British Chemical Manufacturers* Food Manufacturers Federation* Association of British Pharmaceutical Industry Glass Manufacturers Federation Association of Steel Drum Manufacturers* Industrial Management Research As

4、sociation Board of Trade* Institute of Packaging British Carton Association Institution of Production Engineers British Paper Bag Federation National Federation of Box and Packing Case British Paper Box Federation Manufacturers British Railways, The Railway Executive* National Federation of Employer

5、s of Coopers in British Tin Box Manufacturers Federation* the United Kingdom Collapsible Tube Manufacturers Federation National Federation of Grocers and Provision Co-operative Wholesale Society Ltd. Dealers Associations Cotton Bag Manufacturers Association National Paint Federation* Crown Agents fo

6、r the Colonies Printing, Packaging and Allied Trades Envelope Makers and Manufacturing Research Association Stationers Association Society of British Paint Manufacturers Ltd.* Fibreboard Packing Case Manufacturers Association The Government departments and scientific and industrial organizations mar

7、ked with an asterisk in the above list, together with the following, were directly represented on the committee entrusted with the preparation of this British Standard: Admiralty Galvanized Hollow-ware Organization Air Ministry Ministry of Defence (Standardization of Drums Association of British Ins

8、ecticide and Metal Containers Sub-Committee of Manufacturers and Joint Non-warlike Stores Association of British Sheep and Cattle Dip Standardization Committee) Manufacturers Ministry of Food Bakers Sundries Defence Committee Ministry of Labour and National Service British Disinfectant Manufacturers

9、 (Factory Department) Association Ministry of Supply British Plastics Federation Ministry of Transport Closure Manufacturers Association Oil Companies Materials Committee. Council of British Manufacturers of Petroleum Equipment Amendments issued since publication Amd. No. Date of issue Comments 5226

10、 May1964 Indicated by a sideline in the marginBS1702:1950 BSI 11-1999 i Contents Page Co-operating organizations Inside front cover Foreword ii 1 Scope 1 2 Materials (body, ends, hoops and bands) 1 3 Construction and workmanship 1 4 Reinforcement 1 5 Size, type and class 2 6 Dimensions, tolerances a

11、nd ullage 2 7 Closures 2 8 Finish 3 9 Cleanliness 3 10 Testing 3 11 Marking 4 12 Inspection 4 13 Class5Drum 4 Appendix Vapour pressure determination 6 Figure 1 Reinforcement 2 Figure 2 Pressure test apparatus 7 Table 1 Dimensions of British Standard welded mild steeldrums(heavydutyfixed ends) 5BS170

12、2:1950 ii BSI 11-1999 Foreword This British Standard requires reference to the following standard: BS192, B.S.W. and B.S.F. open-ended carbon steel spanners. This British Standard supersedes BS670:1936, “Welded mild steel drums” and BS829:1939, “Mild steel drums for inflammable liquids,” and is the

13、first of a new series of British Standards for metal drums. BS670 was originally prepared at the joint request of the Association of British Chemical Manufacturers and the British Chemical Plant Manufacturers Association. It covered drums for liquids which do not flash below73 F.(22.7 C.) or develop

14、 a vapour pressure of more than20lb/sq. in. absolute below45 C.(113 F.) and included provisions for corrosive and heavy liquids. The preparation of BS829 was undertaken at the request of the same two organizations as well as the petroleum industry. The standard covered drums for most inflammable liq

15、uids not completely miscible with water and flashing below73 F. when tested in accordance with the requirements of the Petroleum (Consolidation) Act,1928, and represented an advance in the technique of transporting petroleum products of an inflammable nature. As a result of extensive tests carried o

16、ut by the railways and the oil companies it was found possible to standardize lighter drums than those previously in use. In arriving at the requirements for the constructional strength of the drum the conditions of transport normally associated with returnable packages were taken into consideration

17、. The present revision and amalgamation of these two standards has become necessary because of a demand from users that a wider range of drums should be specified, and that its details should be simplified. In view of the alternative methods of construction frequently used for drums having bodies th

18、inner than18B.G., such drums are omitted from the standard. It is pointed out that, although compliance with this British Standard will ensure satisfactory drums, the continuance of their serviceability will depend on systematic and periodic inspection and maintenance. A British Standard does not pu

19、rport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front

20、 cover, pagesi andii, pages1 to8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS1702:1950 BSI 11-1999 1 1 Scope This British Standard cover

21、s heavy duty welded mild steel drums with fixed ends, with capacities from590imperial gal. It does not apply to the special drums required for the storage and conveyance of the following liquids: carbon disulphide 1)any liquid not complying with the pressure test described in the Appendix. The stand

22、ard also covers the44imperial gallon drum used by the petroleum industry. 2 Materials (body, ends, hoops and bands) a) Quality. The drums shall be made from thoroughly annealed good commercial quality low carbon mild steel sheets. End bands and rolling hoops shall be made of low carbon steel of good

23、 welding quality. b) Thickness. The thickness of the sheet metal used for the body and the end of the drums shall conform to the dimensions given in Table 1. The permissible variation in each gauge shall be as specified in BS1449 “Steel plate, sheet and strip”. 3 Construction and workmanship a) Body

24、. The body of the drums shall be made from a single sheet of metal. b) Ends. The ends, after being flanged to the appropriate depth, shall be a good fit in the body of the drum. c) Welding. All drums shall be welded by a suitable welding process. d) Rolling hoops and beads. Drums under20imperial gal

25、. in nominal capacity shall normally be supplied with a plain body, but if required by the purchaser two rolling hoops, not less than* in. deep, shall be pressed out from the body of the drum. Round the body of drums of20imperial gal. and over nominal capacity shall be fitted two1“ in. 1in. “I” sect

26、ion mild steel rolling hoops, weighing2lb/ft, or where agreed between manufacturer and customer there shall be pressed out from the body of the drum two rolling hoops not less than# in deep. The “I” section mild steel rolling hoops shall be shrunk on or, where required, secured by means of a small b

27、ead formed in the body of the drum on each side of the rolling hoop. NOTEThe latter method is not recommended for galvanized drums. e) Reinforcement. The circumferential junction of the body and ends shall be reinforced with mild steel bands of either lipped or convex feather edge section, as specif

28、ied in Clause4 (see Figure 1). f) Closures. The drums shall be fitted with screw bungs, flanges and washers as specified in Clause7. 4 Reinforcement The circumferential seam at each end of the drum shall be strengthened by either lipped or convex feather edge section bands, made from mild steel bars

29、 of the type and dimensions shown below: Drums under20 imperial gal. nominal capacity Drums20 imperial gal. nominal capacity and over When Type A construction is used the body and ends of the drum shall be welded together by a suitable process and the external lipped section band shrunk into positio

30、n. When Type B or C construction is used the body, ends and convex section bands shall be welded together. 1) The construction of drums for carbon disulphide is specified in Statutory Rules and Orders1935, No.283,1st Schedule. Lipped section external bands 1# in.) in.* in. as Type A. or Convex secti

31、on external bands 1in.! in. as Type C. Lipped section external bands 1# in.) in.* in. as Type A. or Convex section external bands 1“ in.) in. as Type B. Convex section internal bands 1in.! in. BS1702:1950 2 BSI 11-1999 5 Size, type and class Drums shall be designated by the appropriate nominal capac

32、ity, type and class shown in Table 1. 6 Dimensions, tolerances and ullage a) Dimensions. The drums shall conform to the dimensions given in Table 1, subject to the tolerances specified in Clause6 b). These dimensions provide for an ullage of not less than5percent (e.g.a50imperial gal. drum would hav

33、e a52“ imperial gal. water capacity). NOTEIf an intermediate capacity or larger ullage is required, the diameter shall be the standard diameter of the drum of the next higher, or lower, capacity, as appropriate. The length shall be such as to provide the required capacity in conjunction with this di

34、ameter. The gauge of metal for the body and ends shall be that given for the next larger standard size of drum of the appropriate class. b) Tolerances. The tolerances on internal diameter and external length shall be( in. 7 Closures Drums shall be provided with bungs and flanges made from good weldi

35、ng quality mild steel drop forgings. The heads of the bungs shall be hexagonal to allow of removal by means of a spanner, and shall have a recess to allow of removal by means of a key. The flange shall be continuously welded around its outer edge to the drum and shall not project into the interior.

36、The underside of the heads of the bungs and the top face of the flanges shall be machined surfaces and they shall be square to the threads. Sealing holes shall be provided in the bungs and in lugs on the flanges to permit the closure to be sealed by means of wire and metal seals. Figure 1 Reinforcem

37、entBS1702:1950 BSI 11-1999 3 Each drum shall be fitted with a large bung and flange, screwed2! in. B.S.F. thread,6 threads per inch, and a small bung and flange, screwed# in. B.S.P. thread,14 threads per inch, conforming to the following dimensions: Dimensions of bungs and flanges NOTEAlthough the c

38、losures specified in this clause are standard, it is recognized that there are other equally effective methods of closure, and their use is not necessarily precluded. Attention is drawn, however, to the necessity of ascertaining that the closures are acceptable to the appropriate transport authoriti

39、es. Drums under 20imperial gal. nominal capacity. The bungs and flanges fitted to these drums shall be placed in one end of the drum, each close to the chimb and diametrically opposed to each other. Drums 20imperial gal. nominal capacity and over. The bungs and flanges may be fitted in one end of th

40、e drum as above, or the large bung and flange may be fitted on the body of the drum between the rolling hoops, and the small bung and flange in one end near the chimb and diametrically opposed to the large bung and flange in the body of the drum. The closures shall be completed with washers made of

41、a material suitable for use with the liquid to be packed in the drum. The closures, when fitted in the end or when fitted in the body of the drum, shall not project above the chimb or rolling hoops. The# in. fittings may be omitted when not required. 8 Finish The purchaser shall specify in his inqui

42、ry and order the nature of the internal and external finish required. 9 Cleanliness The drums, as delivered, shall be thoroughly clean, and shall be free from all traces of rust, loose scale and other foreign matter. 10 Testing a) Pressure test. The drums shall be tested and shall withstand without

43、leakage an air pressure test of10lb/sq. in. under water. 2) b) Drop test. If a drop test is required for special purposes the drum shall be capable of passing the following test, without leakage: The drum, filled with water to98percent of its nominal capacity, shall be held diagonally and dropped fr

44、om a height of4ft.6in. so that, with the drum at the same slant, the chimb hits a solid, level, concrete or brick surface. Bungs 2! in. B.S.F # in. B.S.P. in. in. Width across flats of hexagonal head a Minimum thickness of head Length of shank measured from under head Recess for bung key: Width acro

45、ss the square Depth 2.76 0.25 0.625 0.875 0.625 1.67 0.25 0.625 0.500 0.375 Flanges: Overall diameter Overall diameter of machined face Minimum length of thread 3.500 2.750 0.500 2.375 1.500 0.375 a The manufacturing tolerances of these dimensions shall be minus, so as to permit the use of British S

46、tandard spanners specified in BS192, “B.S.W. and B.S.F. open-ended carbon steel spanners.” 2) Attention is drawn to the need for taking adequate precautions against the risks that may be involved in testing with compressed air.BS1702:1950 4 BSI 11-1999 The cost of the drum and the test shall be born

47、e by the purchaser. 11 Marking When specified by the purchaser the drum shall have the following marks embossed on one end, in type of a size appropriate to the gauge, but in no case exceeding2in. in height: a) The manufacturers identification mark. b) The number of this British Standard, and class

48、of drum, e.g.“BS1702/.” 3) c) The gauge of the material of the body, the capacity, and the year of manufacture, in the following manner: (i.e.a drum with a14B.G. body, having50imperial gal. capacity, made in1950.) 12 Inspection The manufacturer shall give the purchaser or his representative permissi

49、on to witness the testing and inspection of the drums after manufacture. 13 Class5drum The44imperial gal. drum for the petroleum industry (known as Class5) shall comply in all respects with Clauses212 inclusive, except that it shall be provided with two pressed out rolling hoops not less than# in. deep, in place of “I” section hoops, and with additional strengthening corrugations if so ordered. The dimensions of the drum shall be: The body and ends shall be of14B.G. steel. 3) NOTEAttention is directed to the fact that the follo