ASTM F2367-2004a(2018) Standard Specification for Labeling for Upright Brooms for Consumer and Institutional Use《消费者和机构用立式扫帚标签的标准规范》.pdf

《ASTM F2367-2004a(2018) Standard Specification for Labeling for Upright Brooms for Consumer and Institutional Use《消费者和机构用立式扫帚标签的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2367-2004a(2018) Standard Specification for Labeling for Upright Brooms for Consumer and Institutional Use《消费者和机构用立式扫帚标签的标准规范》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2367 04a (Reapproved 2018)Standard Specification forLabeling for Upright Brooms for Consumer and InstitutionalUse1This standard is issued under the fixed designation F2367; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revisi

2、on, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers uniform labeling criteria andpackage requirements for upright brooms for con

3、sumer andinstitutional use.1.2 The values stated in inch-pound units are to be regardedas standard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user

4、 of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in t

5、he Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Significance and Use2.1 Information on the wording of the labels that appear onthe brooms or broom packaging will

6、help to ensure thataccurate information on material content is presented to theconsumer.3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 broomcorna grain sorgum of the species SorghumBicolor (L.) moench.3.1.1.1 DiscussionBroomcorn has a panicle consisting ofuniformly long, elas

7、tic primary branches called fibers, suitablefor manufacturing of corn brooms. To test for broomcorn: first,determine that the species is Sorghum Bicolor (L.) moench;second, remove the primary branches one-by-one; third, deter-mine if the primary branches are longer than 50 cm, more orless uniform in

8、 length, straight instead of wavy, branching onlyat the tip and not from the base, and covered with seeds onlyat the tip, then it is a broomcorn fiber.3.1.2 filler fiberany other type of material used to addvolume or stiffness, or both, in upright broom construction.3.1.3 natural fiberany non-broomc

9、orn vegetable fiberused in whole or part to manufacture an upright broom.3.1.4 upright brooma cleaning tool used to sweep side-to-side which has a head consisting of natural or plastic fibersaffixed to a handle and is usually twine stitched to provide aflare for wider contact with the surface to be

10、swept.4. Classification4.1 Brooms shall be classified and labeled according tomaterial content.4.1.1 100 % BroomcornOnly contains broomcorn fiber.4.1.2 Natural FiberContaining natural fiber and broom-corn with less than 100 % broomcorn fiber content.4.1.3 Substitute FiberContaining any combination o

11、fnatural and filler fiber with no broomcorn fiber.4.2 Brooms shall be classified and labeled according toweight measure, determined as follows: the weight measure isthe average weight per dozen of 2 dozen brooms, +0 lb/1lb/dozen for classifications 4.2.1 4.2.4, and 62 lb/dozen forclassifications 4.2

12、.5 and 4.2.6. Brooms must conform tominimum weight standards per classification along with otherfunctional parameters as described by each classification. Eachindividual broom must be legibly labeled with the followingtwo items in addition to any other label(s) required by thisspecification: (1) the

13、 type of broom as defined in 4.2.1 4.2.6;and (2) the weight of the broom stated as Size XX, where xxis the weight of the broom per dozen as defined in this section.4.2.1 Whisk Broom, shall weigh 3 lb or more per dozen andconstructed in a manner to be held by hand without anyprotruding handle.4.2.2 T

14、oy Broom, shall weigh 5 lb or more per dozen,constructed on a handle with a diameter not less than58 in. andnot more than78 in., with an overall length not less than 30 in.and not more than 36 in.4.2.3 Lobby Broom, shall weigh 8 lb or more per dozen,constructed on a handle with a diameter not less t

15、han58 in. and1This specification is under the jurisdiction of ASTM Committee F15 onConsumer Products and is the direct responsibility of Subcommittee F15.54 onBrooms and Mops.Current edition approved Feb. 1, 2018. Published February 2018. Originallyapproved in 2004. Last previous edition approved in

16、 2004 as F2367 04a (2010).DOI: 10.1520/F2367-04AR18.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in th

17、e Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1not more than78 in., with an overall length not less than 36 in.and not more than 42 in.4.2.4 Household Broom, shall

18、weigh 14 lb or more perdozen, constructed on a handle with a diameter not less than1316 in. and not more than1516 in., with an overall length notless than 52 in.4.2.5 Janitor Broom, shall weigh 25 lb or more per dozen,constructed on a handle with a diameter not less than 1 in., withan overall length

19、 not less than 54 in.4.2.6 Warehouse Broom, shall weigh 28 lb or more perdozen, constructed on a handle with a diameter not less than 1in., with an overall length not less than 54 in.5. Requirements5.1 General:5.1.1 Manufacturers of brooms shall include in their printedcopy on the broom packaging an

20、y and all labeling information.5.1.2 In the case of a broom that is sold without packaging,the manufacturer will provide similar printed copy on aself-adhesive label which will be affixed to the handle near thehead. The label, when placed on the container, shall notthereafter be covered, obstructed,

21、 or removed by distributors orretailers.5.1.3 The printed copy or label shall be easily recognizedand read.5.1.4 The printed copy or label shall indicate the classifica-tion of the broom based on Section 4 definitions.5.1.5 Products complying with all the requirements of thisprovisional standard sha

22、ll include “Meets ASTM F2367” orequivalent in the printed copy or label.6. Keywords6.1 broomcorn; brooms; consumer products; labelingASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standar

23、d are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif

24、not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, whic

25、h you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,Un

26、ited States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 04a (2018)2