ASTM F1664-2008(2018) Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Tension Wire Used with Chain-Link Fence《与链节栅栏一起使用的聚氯乙烯.pdf

《ASTM F1664-2008(2018) Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Tension Wire Used with Chain-Link Fence《与链节栅栏一起使用的聚氯乙烯.pdf》由会员分享，可在线阅读，更多相关《ASTM F1664-2008(2018) Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Tension Wire Used with Chain-Link Fence《与链节栅栏一起使用的聚氯乙烯.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1664 08 (Reapproved 2018)Standard Specification forPoly(Vinyl Chloride) (PVC) and Other Conforming OrganicPolymer-Coated Steel Tension Wire Used with Chain-LinkFence1This standard is issued under the fixed designation F1664; the number immediately following the designation indicates th

2、e year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers PVC and other conforming

3、organic polymer-coated steel tension wire for use with chainlink fence. PVC and other organic polymer coatings hereinafterwill be designated as polymer coating.1.2 Tension wire, produced from three classes of wirecoatings, is covered as follows:1.2.1 Class 1, consisting of a polymer coating extruded

4、 overzinc-coated or aluminum-coated or zinc-5 % aluminum-mischmetal alloy-coated steel wire;1.2.2 Class 2a, consisting of a polymer coating extrudedand adhered to zinc-coated or aluminum-coated or zinc-5 %aluminum-mischmetal alloy-coated steel wire; and1.2.3 Class 2b, consisting of a polymer coating

5、 fused andadhered to zinc-coated or aluminum-coated or zinc-5 %aluminum-mischmetal alloy-coated steel wire.1.3 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.1.4 This international standard was developed in accor-dance

6、 with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Stand

7、ards:2A90/A90M Test Method for Weight Mass of Coating onIron and Steel Articles with Zinc or Zinc-Alloy CoatingsA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA428/A428M Test Method for Weight Mass of Coating onAluminum-Coated Iron or Steel ArticlesD1499 Practice for Filter

8、ed Open-Flame Carbon-Arc Expo-sures of PlasticsF552 Terminology Relating to Chain Link FencingF934 Specification for Standard Colors for Polymer-CoatedChain Link Fence MaterialsG152 Practice for Operating Open Flame Carbon Arc LightApparatus for Exposure of Nonmetallic MaterialsG153 Practice for Ope

9、rating Enclosed Carbon Arc LightApparatus for Exposure of Nonmetallic Materials3. Terminology3.1 DefinitionsFor definitions of terms such as fabric(chain-link fence), tension wire, PVC, and polymer coating,see Terminology F552.4. Ordering Information4.1 Orders for tension wire purchased in accordanc

10、e withthis specification shall include the following information:4.1.1 Quantity (expressed in number of coils);4.1.2 Class of coating to be applied to metallic-coated steelwire;4.1.3 Color of coating;4.1.4 Selection of type of metallic coating on the steel wiresubstrate, which shall be the choice of

11、 the producer unlessotherwise specified;4.1.5 Core diameter of wire or minimum wire breakingstrength, or both;4.1.6 Packaging requirements; and4.1.7 Certification, if required.4.2 Any tests required other than those covered specificallyin this specification must be stipulated by the purchaser in the

12、order or contract.NOTE 1A typical ordering description is as follows: 20 coils polymer-coated steel tension wire, Class 2b coating, olive green color, 7-gage(0.177-in. (4.50 mm) core wire, in 1000-ft (305-m) coils, certified to thisspecification.1This specification is under the jurisdiction of ASTM

13、Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire Accessories.Current edition approved March 1, 2018. Published March 2018. Originallyapproved in 1995. Last previous edition approved in 2013 as F166408(2013). DOI:10.1520/F1664-08R18.2For refer

14、enced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West

15、Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trad

16、e Organization Technical Barriers to Trade (TBT) Committee.15. Materials5.1 Base MetalThe base metal shall be steel of suchquality and purity that, when drawn to the size of wire specifiedand coated with an organic polymer, the finished wire shall beof uniform quality and have properties and charact

17、eristics asprescribed in this specification.5.2 Wire used for the manufacture of tension wire shall meetthe requirements of this specification. The polymer coatingshall be formulated and produced properly to conform to therequirements of this specification.6. Manufacture6.1 Class 1 polymer-coated wi

18、re shall have the coatingextruded onto wire that conforms to the requirements as givenin Table 1.6.2 Class 2a polymer-coated wire shall have the coatingextruded and adhered to wire that conforms to the requirementsas given in Table 1.6.3 Class 2b polymer-coated wire shall have the coatingfused and a

19、dhered to wire that conforms to the requirements asgiven in Table 1.7. Size of Wire7.1 The permissible variation from the specified diameter ofthe core wire, 0.177 in. (4.50 mm) 7 gage or 0.148 in. (3.76mm) 9 gage, shall be 60.005 in. (0.13 mm).8. Breaking Strength8.1 Tension wire shall meet the min

20、imum breaking strengthindicated in Table 2 when tested in accordance with TestMethods and Definitions A370.8.2 Specimens to establish conformance with this require-ment shall comprise individual pieces from a coil of the tensionwire. The specimens shall be of sufficient length so as to begripped fir

21、mly in the testing machine. The polymer coatingmay be removed from the sample by chemical or mechanicalmeans before testing.9. Weight of Metallic Coatings9.1 The weight of the metallic coating shall conform toTable 1.9.2 The weight of the coating shall be determined on anindividual piece of wire ove

22、r 12 in. (305 mm).9.3 The weight of the zinc or zinc-5 % aluminum mis-chmetal alloy coating shall be determined by the methodcontained in Test Method A90/A90M after stripping thepolymer coating as outlined in Section 10.9.4 The weight of the aluminum coating shall be determinedby the method containe

23、d in Test Method A428/A428M afterstripping the polymer coating as outlined in Section 10.10. Thickness of PVC Coating10.1 The thickness of the coating shall be in accordancewith Table 3.10.2 The thickness of the coating shall be determined on anindividual piece of wire. This specimen may be any leng

24、th ofwire over 12 in. (305 mm).10.3 For Class 1 and Class 2a material, strip the coatingmechanically from the wire and measure the minimum andmaximum thickness of the coating with a suitable micrometer.10.4 For Class 2b material, strip the coating by chemicalmeans and determine the diameter of the b

25、are wire. Scrape thecoating from one side of the wire and measure the reduceddiameter with a micrometer. The thickness of the coating at thispoint is the difference between the measurement thus obtainedand the measured diameter of the bare wire. In a similarmanner, determine the thickness of the coa

26、ting at right anglesto the first determination.10.5 Take care not to remove any of the metallic surfacewhen removing polymer coating by scraping.11. Properties of Polymer-Coated Tension Wire11.1 The polymer-coated tension wire shall have a demon-strated ability to conform to the following requiremen

27、ts:11.2 Adhesion Tests:11.2.1 Class 2a must conform to the requirements of 11.2.2.Class 2b must conform to the requirements of 11.2.3.11.2.2 Three specimens from each lot shall be tested.Measure a distance of34 in. (19 mm) from the end of thespecimen. With a regular hand grip wire stripper, exert ma

28、xi-mum hand pull parallel to the axis of the wire. Attempt toremove the measured portion of the polymer sleeve from thecore wire. The lot shall be acceptable if the polymer sleeve isnot capable of being removed from the core wire on all threesamples.11.2.3 Three specimens from each lot shall be test

29、ed. Maketwo cuts parallel to the axis of the wire through the coating,approximately116 in. (1.6 mm) apart, at least12 in. (12.7 mm)TABLE 1 Breaking Strength of Metallic-Coated Core WireSpecified Diameter of Core Wire,in. (mm)Minimum Breaking Strength,lbf (N)0.177 (4.50) 1950 (8670)0.148 (3.76) 1290

30、(5740)TABLE 2 Weight of Metallic CoatingsSpecified Diameterof Core Wire, in.(mm)Minimum Weightof Zinc Coating,oz/ft2(g m2)Minimum Weightof AluminumCoating, oz/ft2(g/m2)Minimum Weight ofZinc-5 % Aluminum-Mischmetal Coating,oz/ft2(g m2)0.177 (4.50) 0.40 (122) 0.20 (61) 0.40 (122)0.148 (3.76) 0.30 (92)

31、 0.20 (61) 0.30 (92)TABLE 3 Thickness of Polymer CoatingClass 1 andClass 2a, in.(mm)Class 2b,in. (mm)Minimum thickness at any point 0.015 (0.38) 0.006 (0.15)Maximum thickness at any point 0.025 (0.64) 0.012 (0.30)F1664 08 (2018)2long. With a knife, peel back a section of the coating between18 and14

32、in. (3.2 and 6.4 mm) long to produce a tab. Attemptto remove the116-in. (1.6-mm) strip of coating by pulling thetab. The lot shall be acceptable if the coating breaks rather thanseparates from the core wire on all three specimens.11.3 Accelerated AgingThe polymer-coated wire shallwithstand exposure

33、for 1000 h without failure at a black paneltemperature of 145F (63C) when tested in accordance withPractice D1499. The appropriate apparatus described in Prac-tices G152 or G153 shall be used for the test. The product shallbe construed to have failed the test if one of the followingoccurs:11.3.1 Shr

34、inkage of the polymer coating shall be no greaterthan116 in./ft (1.6 mm/305 mm) of wire, or11.3.2 There shall be no significant change in color or glossof the polymer surface as determined by visual inspection.11.4 ColorUnless otherwise stipulated by the purchaser,the color of the coating shall be i

35、n accordance with the standardcolors contained in Specification F934: green, olive green,brown, and black.12. Workmanship12.1 The polymer-coated tension wire shall be produced bymethods recognized as good commercial practices. The coatingshall be without voids. The coated wire shall be manufacturedw

36、ithout tears or cuts that reveal the substrate.13. Standard Length of Coils13.1 The standard length of coils shall be 1000 ft (305 m)61 % except as otherwise agreed upon at the time of purchase.14. Field Sampling and Number of Tests14.1 The purchaser may select at random one coil fromevery 50 coils

37、or fraction thereof for test purposes, except thatin no case shall fewer than two coils be sampled.14.2 Sample coils thus selected shall be checked for wiresize (Section 7).14.3 Test specimens taken from the outside end of thesample coils shall be tested for the class of polymer coating(Section 6 an

38、d Section 11), core wire size (Section 7), breakingstrength (Section 8), weight of metallic coating (Section 9), andthickness of polymer coating (Section 10).14.4 If any specimen tested fails to conform to the specifiedrequirements, the coil represented by the specimen shall berejected and two addit

39、ional coils shall be tested, both of whichshall meet the requirements in every respect; otherwise the lotrepresented by the samples may be rejected.15. Inspection15.1 The supplier is responsible for the performance of allinspection and test requirements as specified herein. Thesupplier may use his o

40、wn or other suitable facilities forinspection and testing unless the purchaser does not approve atthe time the order is placed. The purchaser has the right tomake any of the inspection and tests outlined where such aredeemed necessary.16. Certification and Report16.1 Upon the request of the purchase

41、r in the contract ororder, a manufacturers certification that the material wasproduced in accordance with the specification shall be fur-nished.17. Packaging, Package Marking, and Loading17.1 Marking shall be by a tag attached securely to each coilof tension wire and shall indicate the identity of t

42、he producer,quantity, core wire size, type of coating, class of coating (ifapplicable), and ASTM designation.17.2 Packaging of the coils of wire shall be agreed uponbetween the producer and the purchaser. This agreement mayinclude the coil dimension and weight.18. Keywords18.1 chain-link fence; poly

43、mer-coated steel wire; steel wire;tension wire; wireASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rig

44、hts, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for

45、 revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing

46、 you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may

47、 be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 08 (2018)3