ASTM E575-2005(2018) 1250 Standard Practice for Reporting Data from Structural Tests of Building Constructions Elements Connections and Assemblies.pdf

《ASTM E575-2005(2018) 1250 Standard Practice for Reporting Data from Structural Tests of Building Constructions Elements Connections and Assemblies.pdf》由会员分享，可在线阅读，更多相关《ASTM E575-2005(2018) 1250 Standard Practice for Reporting Data from Structural Tests of Building Constructions Elements Connections and Assemblies.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E575 05 (Reapproved 2018)Standard Practice forReporting Data from Structural Tests of BuildingConstructions, Elements, Connections, and Assemblies1This standard is issued under the fixed designation E575; the number immediately following the designation indicates the year oforiginal ado

2、ption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers general use in reporting structuralperformance tes

3、ts of building constructions, elements,connections, and assemblies. A comprehensive report describ-ing the conditions under which the structural data wererecorded will enable other workers to reproduce the testmethods and, as nearly as possible, the results for each materialor assembly, and to recon

4、cile differences that might be found intests by others.1.2 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine t

5、he applicability of regulatory limitations prior to use.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations iss

6、ued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2E631 Terminology of Building Constructions3. Terminology3.1 For definitions of terms used in this practice, seeTerminology E631.4. Significance and Use4.1 This practice provides

7、a standard procedure for report-ing data and results of structural tests used for buildingconstructions, elements, corrections, and assemblies. It enu-merates and discusses the report sections required to reportdata from test methods and practices. The written reports willdescribe the products teste

8、d, method of testing, and results.5. Organization of Report5.1 Generally, a report shall contain the following parts inthe sequence listed:5.1.1 Title page with byline,5.1.2 Object statement,5.1.3 Descriptions of specimen(s) and apparatus,5.1.4 Procedure statement,5.1.5 Discussion of test results,5.

9、1.6 Conclusion,5.1.7 Recommendations,5.1.8 References,5.1.9 Pictures,5.1.10 Tabulations,5.1.11 Calculations, and5.1.12 Supplementary data.5.2 Use the headings listed that are appropriate. Use othermore appropriate headings if they better describe the content.5.3 When the expected readership includes

10、 both experts andlaymen, an early insertion in nontechnical language of thenecessary background, data summary, and results is useful.6. Documented Information6.1 A report shall include the following information, but notnecessarily in the order listed:6.1.1 TitleA title shall be brief but definitive.

11、6.1.2 AuthorOne first name and surname and any profes-sional registration shall be included in a byline for positiveidentification.6.1.3 Date of test and date of report.6.1.4 Test agency, sponsor, and their mailing addresses.6.1.5 Specimen Selection and IdentificationIndicate thenumber of specimens,

12、 method of choosing them, and whetherthey were specially fabricated for this test, prototypes ofplanned production, randomly selected production units, and soforth. If specimens were obtained from routine production,include the manufacturers name, source of supply, specimen1This practice is under th

13、e jurisdiction of ASTM Committee E06 on Perfor-mance of Buildings and is the direct responsibility of Subcommittee E06.11 onHorizontal and Vertical Structures/Structural Performance of Completed Structures.Current edition approved July 1, 2018. Published July 2018. Originally approvedin 1976. Last p

14、revious edition approved in 2011 as E575 05(2011). DOI:10.1520/E0575-05R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe

15、 ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelo

16、pment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1dimensions, model, type, materials, and other pertinent infor-mation such as quality, conditioning, and treatment, includingdata on assembly techniques and

17、 fastenings.6.1.6 Specimen DrawingsDrawings shall provide a de-scription of the physical characteristics and dimensioned sec-tion profiles and any other pertinent construction details. Thisrequirement may be waived if an existing description is easilyavailable and is included by reference. Any modif

18、ication madeto the specimen to obtain a measurement or reading shall benoted. Any unusual characteristics or conditions existing in thespecimen construction prior to test shall be described.6.1.7 Specimen DesignDetails shall be provided for anunderstanding of the principles used in the structural de

19、sign ofthe specimen.6.1.8 Apparatus DescriptionSufficient details shall beprovided to explain the construction, operation, and position ofthe test apparatus. This description may require a presentationof the structural design of the apparatus, especially if it isoriginal in design or operation. This

20、 requirement may bewaived if an existing description is easily available and isincluded by reference.6.1.9 Specimen InstallationIllustrations and a descriptionof details of installation in or attachment to the test apparatusshall be provided for each type of specimen. Details of restraintdevices and

21、 their location relative to the specimen shall bedescribed as well as the locations of loading and reactionpoints.6.1.10 InstrumentationA report shall describe thelocation, direction of measurement, and technical specifica-tions of any instrumentation used to measure loads, reactions,and deformation

22、s generated by the test apparatus and thespecimen. A description of the working condition, tolerances,and accuracy of such meters is useful. The relative deformationmeasured by each gage shall be described.6.1.11 Ambient ConditionsRecords of temperature, rela-tive humidity, moisture content, seasoni

23、ng, and any otherconditions that are relevant to structural performance of thespecimen shall be included. A history of such conditions fromthe time of construction until the time of test may be moresignificant than those present at the time of test, and therefore,if warranted, measurements of ambien

24、t conditions and thecondition of the specimen from the time of specimen construc-tion shall be made.6.1.12 Specimen WeightA report shall state the amount ofdead load of the apparatus or specimen that has been deductedif the net load or strength is reported or that may be deductedif the gross load or

25、 strength is reported.6.1.13 Load-Deformation GraphsGraphs portraying thespecimens response to loading shall be included for eachdeformation-measuring device.6.1.14 Failure Load and DescriptionSpecimens can havemore than one failure mode, for example, ductile or brittlefracture, yielding, excessive

26、deflection, or harmful distortion.Applicable modes of failure shall be described in general termswith criteria for their measurement. A description of eachspecimens failure mode and a value of its ultimate strength ormaximum load or both shall be tabulated.6.1.15 Time Under LoadA load-time record is

27、 needed tointerpret some test results and shall be presented as a graph ortabulation to indicate the time duration for each magnitude ofload.6.1.16 PhotographsPhotographs of the specimen beforeand after testing shall be provided to show what cannot bedescribed easily or clearly by writing. However,

28、if the mode offailure is well known, the photographs are optional.6.1.17 Video (optional)A video may be used as a standardpractice for reporting data from structural tests of buildingconstructions, elements, connections, and assemblies. Thevideo may be used in conjunction with a written test report.

29、Generally, a video should contain the following parts:6.1.17.1 Object statement (title and author),6.1.17.2 Specimen design and selection,6.1.17.3 Apparatus description,6.1.17.4 Specimen installation,6.1.17.5 Instrumentation,6.1.17.6 Ambient conditions,6.1.17.7 Specimen weight (dead and live),6.1.17

30、.8 Testing,6.1.17.9 Failure load and description,6.1.17.10 Time under load,6.1.17.11 Conformity of specimen,6.1.17.12 Officials (technicians, professionals, andobservers), and6.1.17.13 Appendixes.6.1.18 Use the headings listed that are appropriate. Useother more appropriate headings may be used, if

31、they betterdescribe the contents.7. Conformity7.1 A report shall contain a statement indicating whether ornot the construction of the test specimen represents actual orintended construction. If the construction does not representtypical manufacture, deviations shall be noted.7.2 When a standard test

32、 method is used, a statement shallbe included indicating its name and designation. Deviationsfrom it shall be described.8. Officials8.1 Signatures of persons responsible for the supervision ofa test shall be included as well as a list of any official observers.9. Appendixes9.1 All data not specifica

33、lly required by a testing standardbut useful to a better understanding of the test results,conclusions, or recommendations should be appended to areport.10. Keywords10.1 building construction; structural testsE575 05 (Reapproved 2018)2ASTM International takes no position respecting the validity of a

34、ny patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to re

35、vision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. You

36、r comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copy

37、righted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 05 (Reapproved 2018)3