ASTM E2293-2003(2013) Standard Practice for Drying of Metal Bearing Ores Concentrates and Related Metallurgical Materials for the Determination of Mercury《汞测定用含金属矿 精矿和相关冶金材料干燥的标准实施.pdf

《ASTM E2293-2003(2013) Standard Practice for Drying of Metal Bearing Ores Concentrates and Related Metallurgical Materials for the Determination of Mercury《汞测定用含金属矿 精矿和相关冶金材料干燥的标准实施.pdf》由会员分享，可在线阅读，更多相关《ASTM E2293-2003(2013) Standard Practice for Drying of Metal Bearing Ores Concentrates and Related Metallurgical Materials for the Determination of Mercury《汞测定用含金属矿 精矿和相关冶金材料干燥的标准实施.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E2293 03 (Reapproved 2013)Standard Practice forDrying of Metal Bearing Ores, Concentrates, and RelatedMetallurgical Materials for the Determination of Mercury1This standard is issued under the fixed designation E2293; the number immediately following the designation indicates the year o

2、foriginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the sample drying step for thedetermi

3、nation of mercury in ores, concentrates, and relatedmetallurgical materials.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its

4、 use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E50 Practices for Apparatus, Reagents, and Safety Consid-erations for Ch

5、emical Analysis of Metals, Ores, andRelated MaterialsE135 Terminology Relating to Analytical Chemistry forMetals, Ores, and Related MaterialsE877 Practice for Sampling and Sample Preparation of IronOres and Related Materials for Determination of Chemi-cal Composition and Physical PropertiesE882 Guid

6、e for Accountability and Quality Control in theChemical Analysis Laboratory2.2 Other Documents:3ISO 9599 Copper, Lead, and Zinc Sulfide ConcentratesDe-termination of Hygroscopic Moisture in the AnalysisSample-Gravimetric MethodISO 12743 Copper, Lead, and Zinc Sulfide ConcentratesSampling Procedures

7、for the Determination of Metal andMoisture ContentISO 10251 Copper, Lead, and Zinc Sulfide ConcentratesDetermination of Mass Loss of Bulk Material on Drying3. Terminology3.1 DefinitionsFor definitions of terms used in thisPractice, refer to Terminology E135.4. Summary of Practice4.1 Test samples for

8、 be used for mercury determination aredried at 60 C.5. Significance and Use5.1 This practice is primarily to be used to dry samples forthe determination of mercury test portions, and it should not beused for the determination of sample moisture content. Mostsample preparation methods prescribe dryin

9、g the samples at105 C, until a constant mass is obtained. The moisture contentis determined as the percentage mass loss on drying. However,since mercury can volatize from samples at the normallyutilized temperature, samples that are to be used for mercurydetermination shall be dried at 60 C (see Pra

10、ctice E877,ISO 9599, ISO 12743, and ISO 10251).5.2 It is assumed that all who use this practice will betrained analysts capable of performing skillfully and safely. Itis expected that work will be performed in a properly equippedlaboratory under appropriate quality control practices such asthose des

11、cribed in Guide E882.6. Apparatus6.1 Drying Oven, ventilated with forced circulation of air,regulated at a temperature of 60 C 6 2 C.6.2 Top-Loading Balance, minimum precision of 0.01 %.6.3 Drying Trays, capable of holding at least a 1 kg sample,spread no thicker than 3 cm deep.7. Hazards7.1 For pre

12、cautions to be observed in this practice, refer toPractices E50.1This practice is under the jurisdiction of ASTM Committee E01 on AnalyticalChemistry for Metals, Ores, and Related Materials and is the direct responsibility ofSubcommittee E01.02 on Ores, Concentrates, and Related Metallurgical Materi

13、als.Current edition approved Nov. 1, 2013. Published December 2013. Originallyapproved in 2003. Last previous edition approved in 2008 as E2293 03(2008)1.DOI: 10.1520/E2293-03R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org.

14、 For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from International Organization for Standardization (ISO), 1, ch. dela Voie-Creuse, Case postale 56, CH-1211, Geneva 20, Switzerland, http:/www.iso.ch.Copyright ASTM Inter

15、national, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States17.2 Mercury can form vapors at low temperatures. Mercuryvapors can be hazardous to your health. Perform method inventilated areas or wear special health protection equipment.8. Procedure8.1 Remove a represe

16、ntative laboratory sample, 500 gminimum, from the gross sample.8.2 Place the laboratory sample into a drying tray and levelto approximately 3 cm.8.3 Weigh to within 0.01 g on the top loading balance.8.4 Place the tray and test portion into the drying oven anddry at 60 C for at least 16 h.NOTE 1Once

17、the drying period has commenced, no other wet samplesshould be placed into the same drying oven.8.5 Remove the tray and laboratory sample from the ovenand weigh. Dry the tray and laboratory sample for an additional4 h. Remove from the oven and weigh again. Repeat this stepas necessary until two succ

18、essive determinations of the mass ofthe tray plus dried laboratory sample agree within 0.2 %percent relative. (See ISO 9599, ISO 12743, and ISO 10251.)NOTE 2Any crusts or cakes that form on the laboratory sample afterinitial drying should be broken up to enable easier release of moisture.8.6 Prepare

19、 the dried test sample for the determination ofmercury according to the appropriate technique.9. Keywords9.1 drying; mercury; moisture; sample preparationASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.

20、Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed ev

21、ery five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible tech

22、nical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohoc

23、ken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).E2293 03 (2013)2