ASTM E1316-2009 402 Standard Terminology for Nondestructive Examinations.pdf

《ASTM E1316-2009 402 Standard Terminology for Nondestructive Examinations.pdf》由会员分享，可在线阅读，更多相关《ASTM E1316-2009 402 Standard Terminology for Nondestructive Examinations.pdf（33页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E 1316 09Standard Terminology forNondestructive Examinations1This standard is issued under the fixed designation E 1316; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parenthese

2、s indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INDEX OF TERMSSectionA: Common NDT TermsB: Acoustic Emission (AE) TermsC: Electromagnetic Testing (ET) TermsD: Gamma- and X-Radiologic Testing (RT) TermsE: Leak Testin

3、g (LT) TermsF: Liquid Penetrant Testing (PT) TermsG: Magnetic Particle Testing (MT) TermsH: Neutron Radiologic Testing (NRT) TermsI: Ultrasonic Testing (UT) TermsJ: Infrared Testing (IRT) TermsK: Holographic Testing (HT) TermsL: Visual Testing (VT) Terms1. Scope1.1 This standard defines the terminol

4、ogy used in thestandards prepared by the E07 Committee on NondestructiveTesting. These nondestructive testing (NDT) methods include:acoustic emission, electromagnetic testing, gamma- andX-radiology, leak testing, liquid penetrant testing, magneticparticle testing, neutron radiology and gauging, ultr

5、asonictesting, and other technical methods.1.2 Committee E07 recognizes that the terms examination,testing and inspection are commonly used as synonyms innondestructive testing. For uniformity and consistency in E07nondestructive testing standards, Committee E07 encouragesthe use of the term examina

6、tion and its derivatives whendescribing the application of nondestructive test methods.There are, however, appropriate exceptions when the term testand its derivatives may be used to describe the application ofa nondestructive test, such as measurements which produce anumeric result (for example, wh

7、en using the leak testingmethod to perform a leak test on a component, or an ultrasonicmeasurement of velocity).Additionally, the term test should beused when referring to the NDT method, that is, RadiologicTesting (RT), Ultrasonic Testing (UT), and so forth. (Example:Radiologic Testing (RT) is ofte

8、n used to examine material todetect internal discontinuities.)1.3 Section A defines terms that are common to multipleNDT methods, whereas, the subsequent sections define termspertaining to specific NDT methods.1.4 As shown on the chart below, when nondestructivetesting produces an indication, the in

9、dication is subject tointerpretation as false, nonrelevant or relevant. If it has beeninterpreted as relevant, the necessary subsequent evaluationwill result in the decision to accept or reject the material. Withthe exception of accept and reject, which retain the meaningfound in most dictionaries,

10、all the words used in the chart aredefined in Section A.1This terminology is under the jurisdiction of Committee E07 on NondestructiveTesting and is the direct responsibility of Subcommittee E07.92 on EditorialReview.Current edition approved March 1, 2009. Published March 2009. Originallyapproved in

11、 1989. Last previous edition approved in 2008 as E 1316 08a.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.Copyright by ASTM Intl (all rights reserved); Mon Apr 20 21:05:17 EDT 2009Downloaded/printed byGuo Dehua (CNIS) pursuant to L

12、icense Agreement. No further reproductions authorized.2. Referenced Documents2.1 ASTM Standards:2NOTE 1This standard defines the terminology used in the standardsprepared by Committtee E07 on Nondestructive Testing and published inthe Annual Book of ASTM Standards, Volume 03.03.3. Significance and U

13、se3.1 The terms found in this standard are intended to be useduniformly and consistently in all nondestructive testing stan-dards. The purpose of this standard is to promote a clearunderstanding and interpretation of the NDT standards inwhich they are used.4. TerminologySection A: Common NDT TermsTh

14、e terms defined in Section A are the direct responsibility of Subcommittee E07.92, Editorial Review.acceptable quality levelthe maximum percent defective orthe maximum number of units defective per hundred unitsthat, for the purpose of sampling test, can be consideredsatisfactory as a process averag

15、e.calibration, instrument, nthe comparison of an instrumentwith, or the adjustment of an instrument to, a knownreference(s) often traceable to the National Institute ofStandards and Technology (NIST). (See also standardiza-tion, instrument.)cognizant engineering organizationthe company, govern-ment

16、agency or other authority responsible for the design, orend use, of the material or component for which nondestruc-tive testing is requiredDISCUSSIONIn addition to design personnel, the cognizant engineer-ing organization could include personnel from engineering, materialand process engineering, str

17、ess analysis, nondestructive testing, qualityassurance and others, as appropriate.defect, none or more flaws whose aggregate size, shape,orientation, location, or properties do not meet specifiedacceptance criteria and are rejectable.discontinuity, na lack of continuity or cohesion; an inten-tional

18、or unintentional interruption in the physical structureor configuration of a material or component.evaluationdetermination of whether a relevant indication iscause to accept or to reject a material or component.examination, na procedure for determining a property (orproperties) or other conditions o

19、r characteristics of a materialor component by direct or indirect means.NOTE 2Examples include utilization of X-rays or ultrasonic wavesfor the purpose of determining (directly or by calculation) flaw content,density, or (for ultrasound) modulus; or detection of flaws by induction ofeddy currents, o

20、bserving thermal behavior, AE response, or utilization ofmagnetic particles or liquid penetrants.false indication, nan NDTindication that is interpreted to becaused by a condition other than a discontinuity or imper-fection.flaw, nan imperfection or discontinuity that may be detect-able by nondestru

21、ctive testing and is not necessarily reject-able.flaw characterization, nthe process of quantifying the size,shape, orientation, location, growth, or other properties, of aflaw based on NDT response.imperfection, na departure of a quality characteristic fromits intended condition.indicationthe respo

22、nse or evidence from a nondestructiveexamination.DISCUSSIONAn indication is determined by interpretation to berelevant, non-relevant, or false.inspection, nsee preferred term examination.interpretationthe determination of whether indications arerelevant or nonrelevant.interpretation, nthe determinat

23、ion of whether indicationsare relevant, nonrelevant, or false.Nondestructive Evaluationsee Nondestructive Testing.Nondestructive Examinationsee Nondestructive Testing.Nondestructive Inspectionsee Nondestructive Testing.Nondestructive Testing (NDT), nthe development andapplication of technical method

24、s to examine materials orcomponents in ways that do not impair future usefulness andserviceability in order to detect, locate, measure and evaluateflaws; to assess integrity, properties and composition; and tomeasure geometrical characteristics.nonrelevant indication, nan NDT indication that is caus

25、edby a condition or type of discontinuity that is not rejectable.False indications are non-relevant.reference standard, na material or object for which allrelevant chemical and physical characteristics are known andmeasurable, used as a comparison for, or standardization of,equipment or instruments

26、used for nondestructive testing.(See also standardization, instrument.)relevant indication, nan NDT indication that is caused by acondition or type of discontinuity that requires evaluation.standard(1) a physical reference used as a basis for com-parison or calibration; (2) a concept that has been e

27、stablishedby authority, custom, or agreement to serve as a model orrule in the measurement of quality or the establishment of apractice or procedure.standardization, instrument, nthe adjustment of an NDTinstrument using an appropriate reference standard, to obtainor establish a known and reproducibl

28、e response. (This isusually done prior to an examination, but can be carried outanytime there is concern about the examination or instru-ment response. (See also calibration, instrument.)test, nsee preferred term examination.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcon

29、tact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.E1316092Copyright by ASTM Intl (all rights reserved); Mon Apr 20 21:05:17 EDT 2009Downloaded/printed byGuo Dehua (CNIS) pursuant to Lice

30、nse Agreement. No further reproductions authorized.Section B: Acoustic EmissionThe terms defined in Section B are the direct responsibility of Subcommittee E07.04 on Acoustic Emission Method.acoustic emission (AE)the class of phenomena wherebytransient elastic waves are generated by the rapid releas

31、e ofenergy from localized sources within a material, or thetransient waves so generated. Acoustic emission is therecommended term for general use. Other terms that havebeen used in AE literature include (1) stress wave emission,(2) microseismic activity, and (3) emission or acousticemission with oth

32、er qualifying modifiers.acoustic emission channelsee channel, acoustic emission.acoustic emission count (emission count) (N)see count,acoustic emission.acoustic emission count ratesee count rate, acoustic emis-sion (emission rate or count rate) (N).acoustic emission eventsee event, acoustic emission

33、.acoustic emission event energysee energy, acoustic event.acoustic emission sensorsee sensor, acoustic emission.acoustic emission signal amplitudesee signal amplitude,acoustic emission.acoustic emission signal (emission signal)see signal, acous-tic emission.acoustic emission signature (signature)see

34、 signature,acoustic emission.acoustic emission transducersee sensor, acoustic emission.acoustic emission waveguidesee waveguide, acoustic emis-sion.acousto-ultrasonics (AU)a nondestructive examinationmethod that uses induced stress waves to detect and assessdiffuse defect states, damage conditions,

35、and variations ofmechanical properties of a test structure. The AU methodcombines aspects of acoustic emission (AE) signal analysiswith ultrasonic materials characterization techniques.adaptive locationsource location by iterative use of simu-lated sources in combination with computed location.AE ac

36、tivity, nthe presence of acoustic emission during atest.AE amplitudesee dBAE.AE rms, nthe rectified, time averaged AE signal, measuredon a linear scale and reported in volts.AE signal durationthe time betweenAE signal start andAEsignal end.AE signal endthe recognized termination of an AE signal,usua

37、lly defined as the last crossing of the threshold by thatsignal.AE signal generatora device which can repeatedly induce aspecified transient signal into an AE instrument.AE signal rise timethe time betweenAE signal start and thepeak amplitude of that AE signal.AE signal startthe beginning of an AE s

38、ignal as recognizedby the system processor, usually defined by an amplitudeexcursion exceeding threshold.array, na group of two or more AE sensors positioned on astructure for the purposes of detecting and locating sources.The sources would normally be within the array.arrival time interval (Dtij)se

39、e interval, arrival time.attenuation, nthe decrease in AE amplitude per unit dis-tance, normally expressed in dB per unit length.average signal level, nthe rectified, time averaged AElogarithmic signal, measured on the AE amplitude logarith-mic scale and reported in dBaeunits (where 0 dBaerefers to1

40、 V at the preamplifier input).burst emissionsee emission, burst.channel, acoustic emissionan assembly of a sensor, pream-plifier or impedance matching transformer, filters secondaryamplifier or other instrumentation as needed, connectingcables, and detector or processor.NOTE 3A channel for examining

41、 fiberglass reinforced plastic (FRP)may utilize more than one sensor with associated electronics. Channelsmay be processed independently or in predetermined groups havingsimilar sensitivity and frequency characteristics.continuous emissionsee emission, continuous.count, acoustic emission (emission c

42、ount) (N)the numberof times the acoustic emission signal exceeds a presetthreshold during any selected portion of a test.count, event (Ne)the number obtained by counting eachdiscerned acoustic emission event once.count rate, acoustic emission (emission rate or count rate)(N)the time rate at which em

43、ission counts occur.count, ring-downsee count, acoustic emission, the preferredterm.couplanta material used at the structure-to-sensor interfaceto improve the transmission of acoustic energy across theinterface during acoustic emission monitoring.cumulative (acoustic emission) amplitude distribution

44、 F(V)see distribution, amplitude, cumulative.cumulative (acoustic emission) threshold crossing distributionFt(V)see distribution, threshold crossing, cumulative.dBAEa logarithmic measure of acoustic emission signalamplitude, referenced to 1 V at the sensor, before amplifi-cation.Signal peak amplitud

45、e dBAE! 5 dB1V at sensor! 5 20 log10A1/A0!(1)where:A0= 1 V at the sensor (before amplification), andA1= peak voltage of the measured acoustic emission signal(also before amplification).Acoustic Emission Reference Scale:dBAEValue Voltage at Sensor0120 10 VE1316093Copyright by ASTM Intl (all rights re

46、served); Mon Apr 20 21:05:17 EDT 2009Downloaded/printed byGuo Dehua (CNIS) pursuant to License Agreement. No further reproductions authorized.40 100 V60 1 mV80 10 mV100 100 mVDISCUSSIONIn the case of sensors with integral preamplifiers, theAOreference is before internal amplification.dead timeany in

47、terval during data acquisition when theinstrument or system is unable to accept new data for anyreason.differential (acoustic emission) amplitude distribution F(V)see distribution, differential (acoustic emission) ampli-tude f(V).differential (acoustic emission) threshold crossing distributionft(V)s

48、ee distribution, differential (acoustic emission)threshold crossing.distribution, amplitude, cumulative (acoustic emission)F(V)the number of acoustic emission events with signalsthat exceed an arbitrary amplitude as a function of amplitudeV.distribution, threshold crossing, cumulative (acoustic emis

49、-sion) Ft(V)the number of times the acoustic emissionsignal exceeds an arbitrary threshold as a function of thethreshold voltage (V).distribution, differential (acoustic emission) amplitudef(V)the number of acoustic emission events with signalamplitudes between amplitudes of V and V + DV as afunction of the amplitude V. f(V) is the absolute value of thederivative of the cumulative amplitude distribution F(V).distribution, differential (acoustic emission) thresholdcrossing ft(V)the number of tim