ASTM E176-2015a red 4350 Standard Terminology of Fire Standards《防火标准的标准术语》.pdf

《ASTM E176-2015a red 4350 Standard Terminology of Fire Standards《防火标准的标准术语》.pdf》由会员分享，可在线阅读，更多相关《ASTM E176-2015a red 4350 Standard Terminology of Fire Standards《防火标准的标准术语》.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E176 15E176 15a An American National StandardStandard Terminology ofFire Standards1This standard is issued under the fixed designation E176; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A

2、number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This terminology covers terms, related definitions, and descriptions of terms used or likely to be used in fire-test-responsestandards,

3、 fire-hazard-assessment standards, and fire-risk-assessment standards. Definitions of terms are special-purposedefinitions that are consistent with the standard definitions but are written to ensure that a specific fire-test-response standard,fire-hazard-assessment standard, or fire-risk-assessment

4、standard is properly understood and precisely interpreted.NOTE 1For additional information, refer to ASTM Policy on Fire Standards.21.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to estab

5、lish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.1.3 This fire standard cannot be used to provide quantitative measures.2. Referenced Documents2.1 ASTM Standards:3C1224 Specification for Reflective Insulation for Building Applications

6、C1313 Specification for Sheet Radiant Barriers for Building Construction ApplicationsD3675 Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy SourceD5865 Test Method for Gross Calorific Value of Coal and CokeE108 Test Methods for Fire Tests of Roof Coveri

7、ngsE84 Test Method for Surface Burning Characteristics of Building MaterialsE136 Test Method for Behavior of Materials in a Vertical Tube Furnace at 750CE119 Test Methods for Fire Tests of Building Construction and MaterialsE152 Test Method for Fire Tests Of Door Assemblies (Withdrawn 1995)4E162 Tes

8、t Method for Surface Flammability of Materials Using a Radiant Heat Energy SourceE535 Practice for Preparation of Fire-Test-Response StandardsE603 Guide for Room Fire ExperimentsE163 Test Method for Fire Tests Of Window Assemblies (Withdrawn 1999)4E603 Guide for Room Fire ExperimentsE648 Test Method

9、 for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy SourceE800 Guide for Measurement of Gases Present or Generated During FiresE814 Test Method for Fire Tests of Penetration Firestop SystemsE906/E906M Test Method for Heat and Visible Smoke Release Rates for Materials and

10、 Products Using a Thermopile MethodE970 Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy SourceE1317 Test Method for Flammability of Marine Surface FinishesE1321 Test Method for Determining Material Ignition and Flame Spread PropertiesE1352 Test Met

11、hod for Cigarette Ignition Resistance of Mock-Up Upholstered Furniture AssembliesE1353 Test Methods for Cigarette Ignition Resistance of Components of Upholstered Furniture1 This terminology is under the jurisdiction of ASTM Committee E05 on Fire Standards and is the responsibility of Subcommittee E

12、05.31 on Terminology and Editorial.Current edition approved Feb. 1, 2015Aug. 1, 2015. Published March 2015August 2015. Originally approved in 1961. Last previous edition approved in 20142015 asE176 - 14c.E176 - 15. DOI: 10.1520/E0176-15.10.1520/E0176-15A.2 Available from ASTM Headquarters, 100 Barr

13、Harbor Drive, West Conshohocken, PA 19428.3 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.4 The last approved

14、 version of this historical standard is referenced on www.astm.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict a

15、ll changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2

16、959. United States1E1354 Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen ConsumptionCalorimeterE1355 Guide for Evaluating the Predictive Capability of Deterministic Fire ModelsE1474 Test Method for Determining the Heat Release Rate of Upholstered Furni

17、ture and Mattress Components or CompositesUsing a Bench Scale Oxygen Consumption CalorimeterE1509 Specification for Room Heaters, Pellet Fuel-Burning TypeE1513 Practice for Application of Sprayed Fire-Resistive Materials (SFRMs)E1529 Test Methods for Determining Effects of Large Hydrocarbon Pool Fir

18、es on Structural Members and AssembliesE1537 Test Method for Fire Testing of Upholstered FurnitureE1590 Test Method for Fire Testing of MattressesE1623 Test Method for Determination of Fire and Thermal Parameters of Materials, Products, and Systems Using anIntermediate Scale Calorimeter (ICAL)E1678

19、Test Method for Measuring Smoke Toxicity for Use in Fire Hazard AnalysisE1740 Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wall Covering orCeiling Covering Composites Using a Cone CalorimeterE1822 Test Method for Fire Testing of Stacked ChairsE199

20、5 Test Method for Measurement of Smoke Obscuration Using a Conical Radiant Source in a Single Closed Chamber, Withthe Test Specimen Oriented HorizontallyE2032 Guide for Extension of Data From Fire Resistance Tests Conducted in Accordance with ASTM E 119E2058 Test Methods for Measurement of Material

21、Flammability Using a Fire Propagation Apparatus (FPA)E2061 Guide for Fire Hazard Assessment of Rail Transportation VehiclesE2067 Practice for Full-Scale Oxygen Consumption Calorimetry Fire TestsE2102 Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Rad

22、iant HeaterE2187 Test Method for Measuring the Ignition Strength of CigarettesE2226 Practice for Application of Hose StreamE2307 Test Method for Determining Fire Resistance of Perimeter Fire Barriers Using Intermediate-Scale, Multi-story TestApparatusE2230 Practice for Thermal Qualification of Type

23、B Packages for Radioactive MaterialE2231 Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface BurningCharacteristicsE2257 Test Method for Room Fire Test of Wall and Ceiling Materials and AssembliesE2280 Guide for Fire Hazard Assessment of the Effect

24、of Upholstered Seating Furniture Within Patient Rooms of Health CareFacilitiesE2335 Guide for Laboratory MonitorsE2404 Practice for Specimen Preparation and Mounting of Textile, Paper or Polymeric (Including Vinyl) and Wood Wall orCeiling Coverings, Facings and Veneers, to Assess Surface Burning Cha

25、racteristicsE2405 Test Method for Determination of Fire and Thermal Parameters of Materials Using an Intermediate Scale Test withVertically Oriented Specimen (Withdrawn 2011)4E2536 Guide for Assessment of Measurement Uncertainty in Fire TestsE2573 Practice for Specimen Preparation and Mounting of Si

26、te-Fabricated Stretch Systems to Assess Surface BurningCharacteristicsE2574/E2574M Test Method for Fire Testing of School Bus Seat AssembliesE2599 Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch CeilingMaterials for Building Applications to

27、Assess Surface Burning CharacteristicsE2632/E2632M Test Method for Evaluating the Under-Deck Fire Test Response of Deck MaterialsE2652 Test Method for Behavior of Materials in a Tube Furnace with a Cone-shaped Airflow Stabilizer, at 750CE2653 Practice for Conducting an Interlaboratory Study to Deter

28、mine Precision Estimates for a Fire Test Method with FewerThan Six Participating LaboratoriesE2688 Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning CharacteristicsE2690 Practice for Specimen Preparation and Mounting of Caulks and Sealants to Assess Surface Burning Ch

29、aracteristicsE2707 Test Method for Determining Fire Penetration of Exterior WallAssemblies Using a Direct Flame Impingement ExposureE2726/E2726M Test Method for Evaluating the Fire-Test-Response of Deck Structures to Burning BrandsE2749 Practice for Measuring the Uniformity of Furnace Exposure on Te

30、st SpecimensE2816 Test Methods for Fire Resistive Metallic HVAC Duct SystemsE2837 Test Method for Determining the Fire Resistance of Continuity Head-of-Wall Joint Systems Installed Between RatedWallAssemblies and Nonrated Horizontal AssembliesE2886/E2886M Test Method for Evaluating the Ability of Ex

31、terior Vents to Resist the Entry of Embers and Direct FlameImpingementE176 15a2E2912 Test Method for Fire Test of Non-Mechanical Fire Dampers Used in Vented Construction2.2 ISO Standards5:ISO 1182, Fire Tests-Building Materials-Non-Combustibility TestISO 13943, Fire Safety-Vocabulary3. Significance

32、and Use3.1 DefinitionsTerms and related definitions given in Section 4 are intended for use uniformly and consistently in all fire teststandards and in all fire-test-response standards, fire-hazard-assessment standards, and fire-risk-assessment standards in which theyappear.3.2 Definitions of Terms

33、Specific to This Standard:3.2.1 As indicated in Section 4, terms and their definitions are intended to provide a precise understanding and interpretationof fire-test-response standards, fire-hazard-assessment standards, and fire-risk-assessment standards in which they appear.3.2.2 A specific definit

34、ion of a given term is applicable to the standard or standards in which the term is described and used.3.2.3 Different definitions of the same term, appearing respectively in two or more standards, are acceptable provided each oneis consistent with and not in conflict with the standard definition fo

35、r the same term, that is, concept.3.2.4 Each standard in which a term is used in a manner specially defined (see 1.1 and Section 5) shall list the term and itsdescription under the subheading, Definitions of Terms.3.3 Definitions for some terms associated with fire issues and not included in Termino

36、logy E176 are found in ISO 13943. Whendiscrepancies exist, the definition in Terminology E176 shall prevail.4. Terminology4.1 Terms and their standard definitions within the scope of this standard are given in Section 4 in alphabetical order. AnnexA1 contains the definitions of terms from the sectio

37、n on “Definitions of Terms Specific to This Standard” from ASTM E05standards.4.2 Discussions associated with definitions are printed directly under the appropriate definition. The date following eachdefinition or discussion indicates the year of introduction or of latest revision of that particular

38、definition or discussion.4.3 Definitions:afterglow, npersistence of glowing combustion after both removal of the ignition source and the cessation of any flaming.(2005)6assembly, na unit or structure composed of a combination of materials or products, or both. (1990)burn, vto undergo combustion. (19

39、89)char, vto form carbonaceous residue during pyrolysis or during incomplete combustion. (1979)char, na carbonaceous residue formed by pyrolysis or incomplete combustion. (1979)chimney effectupward movement of hot fire effluent caused by convection currents confined within an essentially verticalenc

40、losure. (2006)DISCUSSIONThis usually draws more air into the fire. (2006)combustible, adjcapable of undergoing combustion. (1985)DISCUSSIONThe term combustible is often delimited to specific fire-exposure conditions. For example, building materials are considered combustible if they arecapable of un

41、dergoing combustion in air at pressures and temperatures that might occur during a fire in a building. Similarly, some materials that arenot combustible under such conditions may be combustible when exposed to higher temperatures and pressures or to an oxygen-enriched environment.Materials that are

42、not combustible in bulk form may be combustible in finely divided form. (1985)combustion, na chemical process of oxidation that occurs at a rate fast enough to produce temperature rise and usually lighteither as a glow or flame. (See also glow and smoldering. ) (1989)5 Available from International S

43、tandardization Organization, ISO Central Secretariat 1, rue de Varemb, Case postale 56, CH-1211, Geneva 20, Switzerland or AmericanNational Standards Institute, 11 West 42nd Street, New York, NY, 10046.6 Date indicates year of introduction or latest review or revision.E176 15a3combustion products, n

44、effluent produced when a material undergoes combustion (see also smoke; see also combustion).(2001)DISCUSSIONThe combustion process releases effluents that have mass, in gaseous, liquid, or solid form, and generates radiant energy, as heat or light, and sometimessound. However, the common usage of t

45、he term combustion products in ASTM E05 standards is only for those which have mass. (2001)composite, nstructured combination of two or more discrete materials. (2008)continuous, adjin data collection, conducted at intervals of 5 s or less. (2008)effective heat of combustion, nthe amount of heat gen

46、erated per unit mass lost by a material, product or assembly, whenexposed to specific fire test conditions (contrast gross heat of combustion) (2003).DISCUSSIONThe effective heat of combustion depends on the test method and is determined by dividing the measured heat release by the mass loss during

47、aspecified period of time under the specified test conditions. Typically, the specified fire test conditions are provided by the specifications of the firetest standard that cites effective heat of combustion as a quantity to be measured. For certain fire test conditions, involving very high heat an

48、d highoxygen concentrations under high pressure, the effective heat of combustion will approximate the gross heat of combustion. More often, the fire testconditions will represent or approximate certain real fire exposure conditions, and the effective heat of combustion is the appropriate measure. T

49、ypicalunits are kJ/g or MJ/kg. (2001)environment, nas related to fire, the conditions and surroundings that may influence the behavior of a material, product, orassembly when it is exposed to ignition sources or fire. (1989)fire, ndestructive burning as manifested by any or all of the following: light, flame, heat, smoke. (1988)fire-characteristic profile, nan array of fire-test-response characteristics, all measured using tests relevant to the same firescenario, for a material, product, or assembly to address, collectively, the corresponding fire hazard. (