ASTM D7815-2017 red 3567 Standard Practice for Handling Transportation and Storage of Halon 1211 Bromochlorodifluoromethane (CF2BrCl)《哈龙1211溴氯二氟甲烷(CF2BrCl)处理 运输和存储的标准实施规程》.pdf

《ASTM D7815-2017 red 3567 Standard Practice for Handling Transportation and Storage of Halon 1211 Bromochlorodifluoromethane (CF2BrCl)《哈龙1211溴氯二氟甲烷(CF2BrCl)处理 运输和存储的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7815-2017 red 3567 Standard Practice for Handling Transportation and Storage of Halon 1211 Bromochlorodifluoromethane (CF2BrCl)《哈龙1211溴氯二氟甲烷(CF2BrCl)处理 运输和存储的标准实施规程》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D7815 12D7815 17Standard Practice forHandling, Transportation, and Storage of Halon 1211,Bromochlorodifluoromethane (CF2BrCl)1This standard is issued under the fixed designation D7815; the number immediately following the designation indicates the year oforiginal adoption or, in the cas

2、e of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers guidance and direction to suppliers, recyclers, reclaimers, purchasers

3、, and users in the handling,transportation, and storage of Halon 1211.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard.1.3 This stan

4、dard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 AST

5、M Standards:2D7673D7673/D7673M Specification for Halon 1211, Bromochlorodifluoromethane (CF2BrCl)2.2 CGA Standards:3C-1 Methods for Pressure Testing Compressed Gas CylindersC-6 Standards for Visual Inspection of Steel Compressed Gas CylindersC-7 Guide to Preparation of Precautionary Labeling and Mar

6、king of Compressed Gas ContainersClassification and Labeling ofCompressed GasesP-1 Standard for Safe Handling of Compressed Gases in ContainersSB-1 Safety Bulletin: Hazards of Refilling or Reusing Compressed Refrigerant (Halogenated Hydrocarbon) Gas CylindersSB-5 Safety Bulletin: Hazards of Reusing

7、Disposable Refrigerant (Halogenated Hydrocarbon) Gas CylindersSB-18 Safety Bulletin: Use of Refrigerant (Halogenated Hydrocarbon) Recovery Cylinders2.3 U.S. Government Standards:4CFR Title 40, Part 82.106 Environmental Protection Agency, Warning Statement RequirementsCFR Title 49, Part 172 U.S. DOT,

8、 Hazardous Materials Table, Special Provisions, Hazardous Materials Communications,Emergency Response Information, and Training RequirementsCFR Title 49, Part 172.101 U.S. DOT, Tables of Hazardous Materials and Special ProvisionsCFR Title 49, Part 173 U.S. DOT, Specifications, Shippers-General Requi

9、rements for Shipping and PackagingsCFR Title 49, Part 178 U.S. DOT Specifications for PackagingsCFR Title 49, Part 180 U.S. DOT, Continuing Qualification and Maintenance of Packagings3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 containersstorage vessel for Halon 1211.3.1.2

10、cylinderscontainers of Halon 1211.1 This practice is under the jurisdiction of ASTM Committee D26 on Halogenated Organic Solvents and Fire Extinguishing Agents and is the direct responsibility ofSubcommittee D26.09 on Fire Extinguishing Agents.Current edition approved Sept. 1, 2012Feb. 1, 2017. Publ

11、ished October 2012February 2017. Originally approved in 2012. Last previous edition approved in 2012 asD7815-12. DOI: 10.1520/D7815-12.10.1520/D7815-17.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Sta

12、ndardsvolume information, refer to the standardsstandards Document Summary page on the ASTM website.3 Available from the Compressed GasAssociation.Compressed GasAssociation (CGA), 14501 George CarterWay, Suite 103, Chantilly,VA20151, http:/.4 Available from Superintendent of Documents, U.S. Governme

13、nt Printing Office, Washington, DC 20036.U.S. Government Publishing Office (GPO), 732 N. CapitolStreet, NW, Washington, DC 20401-0001, http:/www.gpo.gov.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to

14、the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright

15、 ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.1.3 Halon 1211bromochlorodifluoromethane; a compound used to suppress a fire.3.1.4 insulatedplaced in an isolated situation to protect and prevent the transfer of damage.4. Significance and Use

16、4.1 This practice provides requirements for the handling, transportation, and storage of Halon 1211 encountered in distributionthrough both commercial and military channels. It is intended to ensure that Halon 1211 is handled, transported, and stored in sucha way that its physical property values ar

17、e not degraded. Transport may be by various means, such as, but not limited to, highway,rail, water, and air.5. Practice5.1 To ensure safe handling, loading, storing, and transporting of material, personnel shall be trained in the CGA publications,CFR regulations, and other documents, as listed in S

18、ections 2.2 and 2.3, respectively.5.2 Handling:5.2.1 Handling shall be in accordance with CGA Publication P-1 Standard for Safe Handling of Compressed Gases inContainers.Containers and as specified by the manufacturer.5.2.1.1 Personnel who handle or store, or both, cylinders of Halon 1211 shall be t

19、rained properly to recognize and identify thecharacteristics of the product and the proper methods of safely handling full, partly full, and empty cylinders.5.2.2 All Halon transfers between storage containers and recycling processes shall be performed by personnel trained inhandling procedures.5.2.

20、3 Halon 1211 recycling and transfer processes shall be in conjunction with the equipment requirements specified by themanufacturer.5.2.4 Halon 1211 handling shall be in nonsmoking, heater-free, ventilated areas to preclude product accumulation. Provisionsshall be made to ensure that service areas li

21、mit Halon 1211 concentrations to not exceed 1 % by volume for 1 min and 0.01 %by volume for a time weighted exposure of 8 h.5.2.5 Cylinders shall not be over filled. The liquid portion of the liquefied gas shall not completely fill the containerscontainersinternal volume and the pressure shall not e

22、xceed five fourths the service pressure of the container at any temperature up to andincluding 130F (54C). The maximum permitted filling density for Type I product 130 F (54 C). To prevent excessive pressurein accordance with Specification D7673D7673/D7673M shall be 100 lb/ft3, the fill density of T

23、ype 1 product within a containershould not exceed that needed to achieve complete filling of the container at the maximum envisaged storage temperature. Forexample, for a U.S. DOT 4BW260 cylinder, the nitrogen partial pressure shall not exceed 129 psig at 70 F (9.9 bar at 21 C) fora 100 lb/ft3 (1602

24、 kg/m3).kg/m3) fill density, which yields a total pressure of 150 psig at 70 F (11.4 bar at 21 C). For this example,the safe working pressure of the 4BW260 cylinder is not exceeded for temperatures below 131 F (55 C). Filling densityrequirements for Type II product (pure specification) are specified

25、 in CFR Title 49, Part 173.304 and CFR Title 49, Part 173.305.(See Figs. 1 and 2.)5.2.6 Handling of materials should be done in a manner that prevents contamination or commingling of materials other thanHalon 1211.FIG. 1 Vapor Pressure of Halon 1211 versus TemperaturePressure versus Temperature, Eng

26、lish UnitsD7815 1725.2.7 Cylinders shall be free of dirt and contamination that would contribute to or would cause deterioration of the productduring shipment or storage. Precautions should be taken to prevent the entry of oil, water, or any other foreign matter into thecontainer. Unique coatings or

27、 preservatives applied prior to shipment to protect the containers are not considered contamination.5.3 Transportation:5.3.1 Transportation shall be as specified in accordance with DOT regulations of CFR Title 49 .49.5.3.1.1 Shipment of materials between distributors, collectors, recyclers, and recl

28、aimers should be within approved DOTguidelines for Class 2.2, regulated materials.Any further provisions for special transportation or packaging should be agreed uponbetween the collectors, recyclers, and reclaimers.5.3.1.2 The minimum design pressure requirements shall be as stated in CFR Title 49,

29、 Part 173.304. The pressure inside thecontainer at 70F (21C)70 F (21 C) shall not exceed the service pressure for which the container is marked. The pressure insidethe container at 130F (54C)130 F (54 C) shall not exceed five fourths the service pressure for which the container is marked.Fig. 1Figs.

30、 1 and 2 illustratesillustrate the effect of temperature on cylinders filled with mixtures of Halon 1211 and nitrogen.5.3.2 Where possible, transportation shall be by suitable vehicles to preclude cylinder damage by excessive mechanicalvibration, shock, freezing, or deleterious high temperatures thr

31、oughout the entire transport route.5.3.2.1 If cylinders are likely to be subject to unacceptable transport conditions, the cylinders should be placed under insulatedconditions.5.3.3 Compressed gas cylinder permanent marking requirements shall be in accordance with CFR Title 49, Part 178 and mustbe m

32、aintained in legible condition as required by CFR Title 49, Part 173. Warning labels shall be affixed to the cylindersconforming to the requirements of CFR Title 40, Part 82.106.82.106 shall be affixed to the cylinders.5.3.4 Containers used for shipping of Halon 1211 conforming to Specification D767

33、3D7673/D7673M shall be marked inaccordance with CFR Title 49, Part 172 Subpart D “Marking.” The proper shipping name for Specification D7673D7673/D7673MType II (pure) Halon 1211 is “Chlorodifluorobromomethane or Refrigerant Gas R12B1 (do not list both),” UN 1974, Hazard Class2.2 (nonflammable gas).

34、The proper shipping name for nitrogen superpressurized Halon 1211 is “Liquefied Gas, nonflammablecharged with nitrogen,” UN1058, Hazard Class 2.2 (nonflammable gas).5.4 Storage:5.4.1 Storage shall be in accordance with CGAPublication P-1 Standard for Safe Handling of Compressed Gases in Containers,i

35、n qualified cylinders in accordance with CFR Title 49, Parts 173 and 178.5.4.2 Cylinders should be stored in areas that will protect vessels from physical and environmental damage, and tampering fromunauthorized personnel.5.4.2.1 Facilities should be constructed and oriented so that safety requireme

36、nts are fulfilled for storage of pressurized cylinders.5.4.3 Storage containers shall be fitted with pressure-release mechanisms to limit vessel pressure to not more than the minimumrequired test pressure of the cylinder. Safety relief valves shall be set at no less than 75 %, nor more than 100 %, o

37、f the minimumrequired test pressure of the cylinder. Safety relief valves shall be in contact with the vapor space of the cylinder.5.4.3.1 Periodic hydrostatic testing and re-inspection of cylinders used for Halon 11211211 shall comply with CFRTitle 49, Part173.34.180.5.4.4 Containers used for stora

38、ge of Halon 1211 conforming to Specification D7673D7673/D7673M shall be marked inaccordance with CFR Title 49, Part 172 Subpart D “Marking,” and shall be clearly marked and labeled to identify whether theHalon 1211 contained conforms to either Type I or Type II of Specification D7673D7673/D7673M. Th

39、e proper storage name forFIG. 2 Halon 1211 Pressure versus Temperature, SI UnitsD7815 173Specification D7673D7673/D7673M Type II (pure) Halon 1211 is “Chlorodifluorobromomethane or Refrigerant Gas R12B1 (donot list both),” UN 1974, Hazard Class 2.2 (nonflammable gas). The proper storage name for nit

40、rogen superpressurized Halon 1211is “Liquefied Gas, nonflammable charged with nitrogen,” UN1058, Hazard Class 2.2 (nonflammable gas).5.4.5 Insulation shall be placed on pallets or shoring and provisions should be made to prevent excessive shock or thermalfluctuations to cylinders.5.4.6 Cylinders sha

41、ll be stored in a manner that will prevent contamination from external sources.5.4.6.1 If Halon 1211 in accordance with Specification D7673D7673/D7673M is stored in the same area as material not inaccordance with Specification D7673D7673/D7673M, storage shall be segregated or clearly identifiable as

42、 not being similar.5.5 Extreme Elevated Temperature ConsiderationsWhen Type I or Type II mixtures of Halon 1211 and nitrogen may beexposed to constant temperatures at or greater than 131F (55C)131 F (55 C) during transportation or storage, higher containerpressures will be encountered that require a

43、lternative fill in the container to that specified in 5.2.5. A maximum non-condensablegas content of 1.5 % is recommended for long-term storage of Type II Halon 1211. The vapor pressure diagram for Type II Halon1211 is Pressure versus temperature diagrams for Halon 1211 conforming to Specification D

44、7673/D7673M are shown in Fig.1Figs. 1 and 2.6. Inspection6.1 Halon 1211 that has been reclaimed or recycled using approved reclamation systems may be released for reissue, providedtest examination to validate the material to specification is fulfilled.6.1.1 Reclaimed or recycled Halon 1211 that cann

45、ot be proven to comply with Specification D7673D7673/D7673M shall notbe reissued. The material shall be processed by environmentally safe methods until conformance to the product standard isachieved.D7815 1747. Keywords7.1 bromochlorodifluoromethane; chlorodifluorobromomethane; Refrigerant Gas R 12B

46、1; CF2BrCl; chlorodifluorobromometh-ane; compressed gas; compressed liquefied gas; cylinders; explosion suppressant; fire suppressant; Halon 1211; handling;reclamation; recovery; recycling; Refrigerant Gas R 12B1; storage; transportASTM International takes no position respecting the validity of any

47、patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revis

48、ion at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your co

49、mments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 61