ASTM D7445-2017 red 3750 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)《带泡沫塑料背衬的硬质聚氯乙烯(PVC)壁板的标准规格(有背衬的乙烯基壁板)》.pdf
《ASTM D7445-2017 red 3750 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)《带泡沫塑料背衬的硬质聚氯乙烯(PVC)壁板的标准规格(有背衬的乙烯基壁板)》.pdf》由会员分享,可在线阅读,更多相关《ASTM D7445-2017 red 3750 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)《带泡沫塑料背衬的硬质聚氯乙烯(PVC)壁板的标准规格(有背衬的乙烯基壁板)》.pdf(15页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D7445 09D7445 17 An American National StandardStandard Specification forRigid Poly(Vinyl Chloride) (PVC) Siding with Foam PlasticBacking (Backed Vinyl Siding)1This standard is issued under the fixed designation D7445; the number immediately following the designation indicates the year o
2、foriginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope Scope*1.1 This specification establishes requirements for vin
3、yl siding with integral foam plastic backing, where the siding ismanufactured from rigid PVC compound. Performance requirements and test methods addressed by this standard include materialsproperties and dimensions, warp, shrinkage, impact strength, expansion, appearance, and windload wind load resi
4、stance. Methodsof indicating compliance with this specification are also provided.NOTE 1Backed vinyl siding is composed of two major components: the siding and the backing. It is intended that the siding portion comply withSpecification D3679. Applicable portions of Specification D3679 are included
5、in this specification. Additional requirements that pertain only to thebacking as a separate material, or to the combination of siding and backing as a whole, are also included.1.2 Backed vinyl siding shall be tested with the backing material in place or removed, as specified in the applicable requi
6、rementor test method.1.3 The use of PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.1.4 Rigid PVC soffit is covered in Specification D4477.1.5 Siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall al
7、so be made tothe manufacturers installation instructions for the specific product to be installed.NOTE 2Information with regard to siding maintenance shall be obtained from the manufacturer.1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are
8、mathematicalconversions to SI units that are provided for information only and are not considered standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety a
9、nd health practices and determine the applicability of regulatorylimitations prior to use.NOTE 3There is no known ISO equivalent to this standard.1.8 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Pr
10、inciples for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD635 Test Method for Rate of Burning and
11、/or Extent and Time of Burning of Plastics in a Horizontal PositionD696 Test Method for Coefficient of Linear Thermal Expansion of Plastics Between 30C and 30C with a Vitreous SilicaDilatometerD883 Terminology Relating to PlasticsD1042 Test Method for Linear Dimensional Changes of Plastics Caused by
12、 Exposure to Heat and MoistureD1435 Practice for Outdoor Weathering of PlasticsD1600 Terminology for Abbreviated Terms Relating to Plastics1 This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.24 on Plastic Building Prod
13、ucts.Current edition approved Feb. 15, 2009June 1, 2017. Published February 2009July 2017. Originally approved in 1979. Last previous edition approved in 2009 asD7445 09. DOI: 10.1520/D7445-09. 10.1520/D7445-17.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Custo
14、mer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the
15、 previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary o
16、f Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D2244 Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color CoordinatesD2457 Test Met
17、hod for Specular Gloss of Plastic Films and Solid PlasticsD3679 Specification for Rigid Poly(Vinyl Chloride) (PVC) SidingD3892 Practice for Packaging/Packing of PlasticsD4226 Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building ProductsD4477 Specification for Rigid (Unplas
18、ticized) Poly(Vinyl Chloride) (PVC) SoffitD4756 Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and SoffitD5206 Test Method for Windload Resistance of Rigid Plastic SidingD5947 Test Methods for Physical Dimensions of Solid Plastics SpecimensD7209 Guide for Waste Reduction, Resou
19、rce Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn2015)3E84 Test Method for Surface Burning Characteristics of Building MaterialsE631 Terminology of Building ConstructionsE1753 Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films
20、G147 Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests2.2 ASCE Standard:4ASCE 7-027-10 Minimum Design loads for Buildings and Other Structures2.3 International Code Council:5International Building CodeInternational Residential Code2.4 Vinyl S
21、iding Institute, Inc.:6VSI Vinyl Siding Installation Manual (2015)2.5 Structural Building Components Association:7ANSI/SBCA FS 100-2012 Standard Requirements for Wind Pressure Resistance of Foam Plastic Insulating Sheathing Used inExterior Wall Covering Assemblies3. Terminology3.1 Definitions are in
22、 accordance with Terminologies D883, E631, and D1600, unless otherwise specified.3.2 Definitions of Terms Specific to This Standard:3.2.1 backed vinyl sidinga vinyl cladding product sold with manufacturer-installed foam plastic backing material as anintegral part of the cladding product. The vinyl c
23、ladding portion of backed vinyl siding meets the definition of vinyl siding. Backedvinyl siding is intended to be installed only with the integral backing.3.2.2 backing material; foam plastic backinga layer or layers of plastic that has been intentionally expanded to produce areduced-density plastic
24、 containing voids consisting of open or closed cells distributed throughout the plastic.3.2.3 nominalthe value that a manufacturer consistently uses to represent a specific property or dimension of a vinyl sidingproduct in public claims including, but not limited to, product literature, advertisemen
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD74452017RED3750STANDARDSPECIFICATIONFORRIGIDPOLYVINYLCHLORIDEPVCSIDINGWITHFOAMPLASTICBACKINGBACKEDVINYLSIDING

链接地址:http://www.mydoc123.com/p-525500.html