ASTM D7193-2005 Standard Specification for Unsintered Pigmented Polytetrafluoroethylene (PTFE) Extruded Film or Tape《非饱和加色剂的聚四氟乙烯(PTFE)挤制薄膜或窄条带材的标准规范》.pdf

《ASTM D7193-2005 Standard Specification for Unsintered Pigmented Polytetrafluoroethylene (PTFE) Extruded Film or Tape《非饱和加色剂的聚四氟乙烯(PTFE)挤制薄膜或窄条带材的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7193-2005 Standard Specification for Unsintered Pigmented Polytetrafluoroethylene (PTFE) Extruded Film or Tape《非饱和加色剂的聚四氟乙烯(PTFE)挤制薄膜或窄条带材的标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 7193 05Standard Specification forUnsintered Pigmented Polytetrafluoroethylene (PTFE)Extruded Film or Tape1This standard is issued under the fixed designation D 7193; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, th

2、e year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers unsintered, pigmented, ex-truded films or tapes manufactured from polytetrafluoro

3、ethyl-ene, in nominal thicknesses from 0.025 mm (0.001 in.) to 0.51mm (0.020 in.), that are 97 % virgin PTFE in compositionprior to introducing pigments.1.1.1 The use of recycled PTFE for production of unsinteredextruded films or tapes has not been identified at this time.When commercial usable proc

4、esses and materials are avail-able, this specification will be revised to include recycledmaterials.1.2 The values stated in SI units are detailed in IEEE/ASTMSI-10 are to be regarded as the standard. The values given inparentheses are for information only.1.3 This standard does not purport to addre

5、ss all of thesafety problems associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety andhealth practices and determine the applicability of regulatorylimitations prior to use.NOTE 1Although this specification and ISO/DIS 13000-1 (1997) andISO/DIS

6、 13000-2 (1997) differ in approach or detail, data obtainedrelating to specific properties, using either are technically equivalent.NOTE 2This specification is intended to be a complement to Speci-fication D 6585, as the materials covered herein vary significantly enoughdue to their additives to war

7、rant a stand-alone set of requirements.2. Referenced Documents2.1 ASTM Standards:2D 257 Test Methods for DC Resistance or Conductance ofInsulating MaterialsD 618 Practice for Conditioning Plastics and ElectricalInsulating Materials for TestingD 638 Test Methods for Tensile Properties of PlasticsD 88

8、3 Terminology Relating to PlasticsD 1600 Terminology for Abbreviated Terms Relating toPlasticsD 1711 Terminology Relating to Electrical InsulationD 3892 Practice for Packaging/Packing of PlasticsD 6040 Test Methods for Unsintered Polytetrafluoroethyl-ene (PTFE) Extruded Film or TapeD 6585 Specificat

9、ion for Unsintered Polytetrafluoroethyl-ene (PTFE) Extruded Film or TapeE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsIEEE/ASTM SI-10 Standard for Use of the InternationalSystem of Units (SI): The Modern Metric System2.2 ISO Standards:3ISO/DIS 1300

10、0-1 PlasticsPolytetrafluoroethylene (PTFE)Semi-Finished ProductsPart 1: Requirements and Des-ignationISO/DIS 13000-2 PlasticsPolytetrafluoroethylene (PTFE)Semi-Finished ProductsPart 2: Preparation of TestSpecimens and Determination of Properties2.3 GSA Standard:4A-A-58092 Tape, Anti-Seize Polytetraf

11、luoroethylene3. Terminology3.1 DefinitionDefinitions are in accordance with Termi-nologies D 883, D 1711, and Test Methods D 257; and abbre-viated terms are in accordance with Terminology D 1600,unless otherwise specified.3.2 lot, none production run or a uniform blend of two ormore production runs3

12、.3 Definitions of Terms Specific to This Standard:3.3.1 film, nfull width material received as finished film.3.3.2 tape, nmaterial that has been slit from the finishedfilm.3.3.3 tensile strength at yield, nfrom Test Methods D 638,Figure A2.3.1This specification is under the jurisdiction of ASTM Comm

13、ittee D20 onPlastics and is the direct responsibility of Subcommittee D20.15 on ThermoplasticMaterials.Current edition approved July 1, 2005. Published July 2005.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book

14、of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.4Available from General Services Administration, Engineering and CommodityManagement Divisio

15、n (9FTE-10), 400 15th St. SW, Auburn, WA 980011Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.3.4 pigmentliquid or dry matter used as an additive, toalter the color of finished film or tape.4. Classification4.1 This specification c

16、overs three types of unsintered,pigmented, extruded PTFE tapes:4.1.1 Type IThread Seal Tape (TST) with an apparentdensity of 0.50-1.60 g/cm3.4.1.2 Type IILow Density Tape with an apparent densityof 0.60-0.80 g/cm3.NOTE 3Other low apparent density products that do not fall into thisdensity range are

17、available. The values vary on these products and must beagreed to between supplier and purchaser.4.1.3 Type IIIWire and Cable Tape with an apparentdensity of 1.40-1.65 g/cm3.4.2 Grades of tape are identified in Tables 1-3.4.3 A line callout system is used to specify materials in thisspecification. T

18、he system uses pre-defined cells to refer tospecific aspects of this specification, as illustrated below:StandardNumberBlockType SpecificationGradeClass SpecialNotesASTMD 7193III 2 mil - Color to beRoyal BlueFor this example, the line call-out would be: ASTM D 7193,III, 2 MIL, Color to be Royal Blue

19、, that would specify anunsintered wire and cable tape, 2 mil thick, and would have allof the properties listed for that type and grade in the appropri-ate specified properties, tables, or both, in the specificationidentified. A comma is used as the separator between thestandard number and the type.

20、Separators are not neededbetween the type and grade because they are, in turn, Romannumerals and Arabic digits as provided in Section B8. of theForm elongation; extruded; film; fluorocar-bon film; pigmented; PTFE; PTFE tape; tape; tensile; threadseal tape; unsinteredASTM International takes no posit

21、ion respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibilit

22、y.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM

23、 International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address s

24、hown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-8

25、32-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 2 Type II Low Density TapeAwith an Apparent Density of 0.60 to 0.80 g/cm3Grade Apparent Density, g/cm3Thickness Tensile Strength at Yield Elongation at Maximum StrengthMin Max mm Tol (in.) Tol MPa psi Min per

26、cent4 Mil 0.60 0.80 0.102 60.0076 0.004 60.0003 13.10 1900 405 Mil 0.60 0.80 0.127 60.0102 0.005 60.0004 13.10 1900 4010 Mil 0.60 0.80 0.254 60.0127 0.010 60.0005 8.27 1200 40AThe values in this table are the default values for Type II pigmented tape in the thickness listed. Other low apparent densi

27、ty products that do not fall into these rangesare available. Agreement between manufacturer and consumer regarding test values that differ from those seen in this table are acceptable.TABLE 3 Type III Wire and Cable TapeAwith an Apparent Density of 1.40 to 1.65 g/cm3Grade Apparent Density, g/cm3Thic

28、kness Tensile Strength at Yield Elongation at Maximum StrengthMin Max mm Tol (in.) Tol MPa psi Min percent2 Mil 1.4 1.65 0.050 60.0076 0.002 60.0003 12.41 1800 253 Mil 1.4 1.65 0.076 60.0076 0.003 60.0003 11.03 1600 254 Mil 1.4 1.65 0.102 60.0076 0.004 60.0003 10.34 1500 255 Mil 1.4 1.65 0.127 60.00

29、76 0.005 60.0003 9.65 1400 256 Mil 1.4 1.65 0.152 60.0102 0.006 60.0004 7.58 1100 257 Mil 1.4 1.65 0.178 60.0102 0.007 60.0004 6.89 1000 258 Mil 1.4 1.65 0.203 60.0102 0.008 60.0004 6.21 900 259 Mil 1.4 1.65 0.229 60.0102 0.009 60.0004 5.52 800 2510 Mil 1.4 1.65 0.254 60.0127 0.010 60.0005 4.83 700

30、5011 Mil 1.4 1.65 0.279 60.0152 0.011 60.0006 4.48 650 5012 Mil 1.4 1.65 0.305 60.0229 0.012 60.0009 4.14 600 5013 Mil 1.4 1.65 0.330 60.0279 0.013 60.0011 3.79 550 5014 Mil 1.4 1.65 0.356 60.0330 0.014 60.0013 3.10 450 5015 Mil 1.4 1.65 0.381 60.0381 0.015 60.0015 2.76 400 5016 Mil 1.4 1.65 0.406 6

31、0.0406 0.016 60.0016 2.76 400 5017 Mil 1.4 1.65 0.432 60.0432 0.017 60.0017 2.76 400 5018 Mil 1.4 1.65 0.457 60.0457 0.018 60.0018 2.76 400 5019 Mil 1.4 1.65 0.483 60.0483 0.019 60.0019 2.76 400 5020 Mil 1.4 1.65 0.508 60.0508 0.020 60.0020 2.76 400 50AIn cases where actual product thickness is between thickness values called out in this table, the actual thickness shall be rounded to the nearest defined incrementusing guidelines found in Practice E29, and the corresponding requirements applied.D7193053