ASTM D6806-2002(2017) 3125 Standard Practice for Analysis of Halogenated Organic Solvents and Their Admixtures by Gas Chromatography《利用气相色谱法对卤化有机溶剂及其混合物分析的标准实施规程》.pdf

《ASTM D6806-2002(2017) 3125 Standard Practice for Analysis of Halogenated Organic Solvents and Their Admixtures by Gas Chromatography《利用气相色谱法对卤化有机溶剂及其混合物分析的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6806-2002(2017) 3125 Standard Practice for Analysis of Halogenated Organic Solvents and Their Admixtures by Gas Chromatography《利用气相色谱法对卤化有机溶剂及其混合物分析的标准实施规程》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D6806 02 (Reapproved 2017)Standard Practice forAnalysis of Halogenated Organic Solvents and TheirAdmixtures by Gas Chromatography1This standard is issued under the fixed designation D6806; the number immediately following the designation indicates the year oforiginal adoption or, in the

2、 case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the determination of impurities,stabilizers and assay of halogenat

3、ed organic solvents and theiradmixtures by gas chromatography.1.2 It is not the intent of this practice to provide a specificmethod of gas chromatography. The intent of this practice is todefine what is required for a user to demonstrate that a methodto be used is valid. The reason for this approach

4、, as opposed tostating a method, is that gas chromatography is such a dynamicfield that methods are often obsolete by the time they arevalidated. The use of this practice allows the user to use mosteffective technology and demonstrate that the method in usecomplies with a standard practice and is va

5、lid for the analysisof halogenated organic solvents and their admixtures.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practice

6、s and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Re

7、com-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standard:2E180 Practice for Determining the Precision of ASTMMethods for Analysis and Testing of Industrial and Spe-cialty Chemicals (Withdrawn 2009)33. Terminology3.1 Pur

8、ity and assay are used interchangeably in this stan-dard.3.1.1 Purity or assay are defined as 100 sum(impurities +stabilizer) when impurities and stabilizers are expressed in %;3.1.2 Or 100 sum(impurities + stabilizer)/10 000 whenimpurities are expressed in ppm.3.2 Accuracy is defined per A2.2.1 of

9、Practice E180 or theagreement between an experimentally determined value andthe accepted reference value.3.3 Precision is defined per A2.1.7 of Practice E180 or thedegree of agreement of repeated measurements of the sameproperty. It is generally expressed in standard deviations orpercent relative st

10、andard deviation (s/X) 100, also known ascoefficient of variation.4. Summary of Practice4.1 This practice will define the requirements for a gaschromatographic (GC) method to be valid for the determina-tion of impurities, stabilizers and assay of halogenated organicsolvents and their admixtures.1Thi

11、s practice is under the jurisdiction of ASTM Committee D26 on Haloge-nated Organic Solvents and Fire Extinguishing Agents and is the direct responsi-bility of Subcommittee D26.04 on Test Methods.Current edition approved Nov. 1, 2017. Published December 2017. Originallyapproved in 2002. Last previous

12、 edition approved in 2012 as D6806 - 02 (2012).DOI: 10.1520/D6806-02R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe AS

13、TM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized prin

14、ciples on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15. Method Requirements5.1 The GC method must give adequate separation of t

15、heimpurities and stabilizers common to the product in question sothat the instrument response (area counts, millivolts, etc.) to theindividual impurities or stabilizers can be measured withadequate precision and accuracy as defined in Section 6.Process knowledge from the supplier or manufacturer of

16、theproduct is a resource of information as to what those impuritiesand stabilizers are. GC-Mass Spectrometry (GC-MS) is an-other resource to initially determine what components arepresent to be measured. See Table 1 for a list of possibleimpurities and stabilizers for each product.5.2 Non polar capi

17、llary columns of about 0.32 mm by 30 mgenerally work well. Table 2 provides a list of columns thatmay prove suitable for the analysis of the halogenated organicproducts.5.3 Instrument ConditionsThe following GC conditionsare often appropriate for the analysis of halogenated organicproducts and their

18、 admixtures though actual conditions shouldbe optimized for the analysis being performed.5.4 The separation is determined to be adequate by prepar-ing standards of known amounts of the impurities and stabi-lizers in concentrations near enough to the expected concen-trations in the sample for the ins

19、trument response to be linearover the concentration range of interest. Repeated injections(minimum of three) of this standard are made and the accuracyand precision of the method for the individual impurities andstabilizers are determined.5.5 Response to components must not be out of range of thedet

20、ector and should be sufficiently Gaussian (symmetrical) toallow adequate measurement as defined by Section 6. Out ofrange response can be corrected by changing the range of theinstrument or changing sample size.5.6 Purity or assay of unblended halogenated organic sol-vents will be determined by dete

21、rmining the amounts of theindividual impurities and stabilizers and subtracting the total ofthose impurities and stabilizers from 100 %. Purity or assaywill, unless otherwise stated, be determined by subtractingfrom 100, the sum of impurities (as determined by gaschromatography) and stabilizers only

22、. The values for water,acidity, non-volatile matter and other such components will notbe subtracted from 100 % to determine the purity or assay ofthe material in question unless the specifications call for theseitems to be included in the total to be subtracted from 100.5.7 Area percent is generally

23、 not suitable for halogenatedorganic products as the sensitivity to a flame ionizationdetector varies greatly between components, particularly sta-bilizers which do not contain chlorine. Calibration of theinstrument should be done using a standard containing thecomponents of interest in concentratio

24、ns similar to that ex-pected in the sample being analyzed.5.8 Precision for the assay is determined by performingstatistical analysis of the purity or assay of individual injectionswhich is determined by 100 % sum(stabilizers + impurities).The units for assay or purity will be weight percent unlesso

25、therwise specified.6. Precision and Bias46.1 Adequate precision and bias is defined by the needs ofthe user of the method.4A research report is available from ASTM Headquarters. Request RR:D26-1018.TABLE 1 Impurities and StabilizerProductPossible Impuritiesand StabilizersMethylene Chloride Methyl Ch

26、lorideVinyl ChlorideEthyl ChlorideVinylidene ChlorideTrans 1,2-DichloroethyleneCis 1,2-DichloroethyleneChloroformCarbon Tetrachloride2-Methyl-2-ButeneCyclohexaneCyclohexenePropylene OxidePerchloroethylene TrichloroethyleneCarbon Tetrachloride1,1,2-Trichloroethane1,1,2,2-tetrachloroethane1,1,1,2-tetr

27、achloroethanePenta ChloroethaneHexachloroethaneN-Methyl MorpholinePara Tertiary Amyl PhenolCyclohexene OxideBHTN-Methyl PyrroleEthoxy PropionitrileTrichloroethylene Cis and trans 1,2-dichloroethylene1,1,2-trichloroethaneCarbon tetrachloride1,1,2,2-tetrachloroethane1,1,1,2-tetrachloroethaneEthylene D

28、ichloridePropylene DichlorideDiisopropyl AmineButylene OxideThymolN-Methyl PyrroleEthyl AcetateDiisobutyleneTABLE 2 Suggested GC ColumnsDB 624DB 5DB 1701TABLE 3 Instrument ConditionsDetectorFlame ionization detector orother detectorof sufficient sensitivity toaccuratelymeasure components ofinterestI

29、njector Temperature 200 CDetector Temperature 200 COven Temperature for Isothermal 80 CProgrammed Oven Temperature 50 to 200 CCarrier Gas Helium or hydrogenCarrier Gas Flow Rate 1 to 3 mL/minSample Size 0.5 to 1.0 Split Ratio 50:1D6806 02 (2017)26.2 As a general guideline, the following table showsp

30、recision of a good gas chromatographic method. These valueswere determined experimentally in a round robin betweendifferent laboratories in different companies. Automatic injec-tors were in common use in all participating laboratories andwere used in the round robin.6.3 The average and standard devi

31、ation of recovery (aver-age of 3 or 4 results) has been determined to be 100.29 68.02 % with 99.7 % falling between 76 and 124 %. Eighty fivepercent were found to fall between 95 and 105 % recovery.6.4 The lower detection limit can be assumed to be threetimes the noise level of the chromatogram. The

32、 lower quanti-fication limit can be assumed to be ten times the noise level.The noise level is determined by starting a run without aninjection and allowing the run to go to completion through thenormal temperature program and time. Take an average of allof the area counts seen in three such blank r

33、uns. This averagearea count will be the background noise for the method.7. Keywords7.1 accuracy; gas chromatography; halogenated organic sol-vent; precisionASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard

34、. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed

35、every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible te

36、chnical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshoh

37、ocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to pho

38、tocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 4 Expected PrecisionConcentration% RelativeStandard Deviation1to25ppm 1225 to 100 ppm 2100 to 10 000 11to25% 0.825 to 75 % 0.575 to 100 % Direct MeasurementBy Difference0.50.1D6806 02 (2017)3