ASTM D5869-2007a(2013) 3125 Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials《屋顶材料和防水材料的暗炉热暴露用标准实施规程》.pdf

《ASTM D5869-2007a(2013) 3125 Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials《屋顶材料和防水材料的暗炉热暴露用标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D5869-2007a(2013) 3125 Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials《屋顶材料和防水材料的暗炉热暴露用标准实施规程》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D5869 07a (Reapproved 2013)Standard Practice forDark Oven Heat Exposure of Roofing and WaterproofingMaterials1This standard is issued under the fixed designation D5869; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, t

2、he year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice establishes a procedure and conditions oftemperature and time for heat exposure of roofing an

3、d water-proofing materials and systems in the presence of air.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is t

4、heresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsD1079 Terminology Relating to Roofing and Waterp

5、roofingD1566 Terminology Relating to RubberE145 Specification for Gravity-Convection and Forced-Ventilation OvensE230 Specification and Temperature-Electromotive Force(EMF) Tables for Standardized ThermocouplesE1137/E1137M Specification for Industrial Platinum Resis-tance ThermometersE2251 Specifica

6、tion for Liquid-in-Glass ASTM Thermom-eters with Low-Hazard Precision Liquids3. Terminology3.1 DefinitionsFor definitions of terms used in thispractice, refer to Terminologies D883, D1079, and D1566.4. Summary of Practice4.1 Specimens of roofing and waterproofing materials areexposed to heat in a da

7、rk forced-ventilation oven at a specifiedelevated temperature for a known period of time.4.2 This practice specifies an exposure temperature of 70 63C (158 6 5F) in a forced-ventilation oven.4.3 This practice permits the selection of the duration ofheat exposure from three specified time periods, wh

8、ich are 35,90, and 180 6 0.25 consecutive days. The duration selectedmust be included in any report of results obtained by using thispractice.NOTE 1The time period to be used should be specified in any standardthat refers to this practice. European standards for polymer-modifiedbituminous materials

9、specify 180 days at 70C. For research purposes,selection of other time periods and temperatures are permitted, providedthat the precise duration is stated in any report of results.4.4 This practice is also used to condition test specimens fortime periods much shorter than 35 days for the purpose ofc

10、onditioning material before testing. When used for thispurpose, the shorter conditioning time shall be specified in anyreport of test results.5. Significance and Use5.1 Roofing and waterproofing materials and systems un-dergo changes in physical properties as a result of beingsubjected to heat. They

11、 also undergo changes in physicalproperties as they age in service. Since service conditions varywidely, any relationship between changes observed in thispractice and changes in service must be established by the userof this practice.6. Apparatus6.1 OvenThe oven shall have forced ventilation, shall

12、beelectrically heated, and shall conform to the requirements ofSpecification E145, Type IIB. The oven shall be of sufficientsize to accommodate the size and number of specimensselected by the user of this practice.6.2 ThermometerThe thermometer shall be an ASTMthermometer, conforming to the requirem

13、ents for thermometerS12C (or S12F) in accordance with Specification E2251.Asanalternate, any other thermometric device used shall be at least:(1) of equal accuracy to that of the thermometer specified in1This practice is under the jurisdiction ofASTM Committee D08 on Roofing andWaterproofing and is

14、the direct responsibility of Subcommittee D08.02 on SteepRoofing Products and Assemblies.Current edition approved May 1, 2013. Published May 2013. Originallyapproved in 1995. Last previous edition approved in 2007 as D5869 07a. DOI:10.1520/D5869-07AR13.2For referenced ASTM standards, visit the ASTM

15、website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United S

16、tates1Specification E2251,(2) capable of indicating temperature towithin 1C (2F), and (3) stable to within 1C (2F) for theduration of the exposure.6.2.1 When used, platinum resistance thermometers shall bein accordance with the requirements of Specification E1137/E1137M.6.2.2 When used, thermocouple

17、s shall be in accordancewith the requirements of Specification E230.7. Specimens7.1 The number, geometry, and size of specimens shall bedetermined by the user of this practice.8. Heat Exposure8.1 Expose the specimens in a forced-ventilation oven at 706 3C (158 6 5F ).8.2 The specimens shall be suppo

18、rted in the oven onshelves, plates, or other containers appropriate to the specimenbeing studied. Specimens shall be separated on shelves toallow free access of air. The specimen orientation, vertical,horizontal, and so forth, shall be determined by the user of thispractice.8.3 The duration of expos

19、ure of the specimens to the heatshall be selected by the user of this practice from the followingoptions: (1)356 0.25 consecutive days; (2)906 0.25consecutive days; or (3) 180 6 0.25 consecutive days. (Seealso 4.4.)9. Report9.1 Report the following information:9.1.1 State the geometry of the specime

20、n, orientation duringthe exposure, and nature of support.9.1.2 Report the duration of exposure to the heat.10. Keywords10.1 dark oven exposure; heat exposure ; roofing andwaterproofing materialsASTM International takes no position respecting the validity of any patent rights asserted in connection w

21、ith any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible tec

22、hnical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful considera

23、tion at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr H

24、arbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D5869 07a (2013)2