ASTM D5486 D5486M-2006(2012) Standard Specification for Pressure-Sensitive Tape for Packaging Box Closure and Sealing 《包装、箱盒封闭和密封用压敏胶带标准规格》.pdf

《ASTM D5486 D5486M-2006(2012) Standard Specification for Pressure-Sensitive Tape for Packaging Box Closure and Sealing 《包装、箱盒封闭和密封用压敏胶带标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM D5486 D5486M-2006(2012) Standard Specification for Pressure-Sensitive Tape for Packaging Box Closure and Sealing 《包装、箱盒封闭和密封用压敏胶带标准规格》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D5486/D5486M 06 (Reapproved 2012)Standard Specification forPressure-Sensitive Tape for Packaging, Box Closure, andSealing1, 2This standard is issued under the fixed designation D5486/D5486M; the number immediately following the designation indicates theyear of original adoption or, in t

2、he case of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This

3、 specification covers film, paper, and cloth pressure-sensitive tapes used for box closure and sealing.1.2 The values stated in either inch-pound or SI units are tobe regarded separately as standard. The values stated in eachsystem may not be exact equivalents; therefore, each systemmust be used ind

4、ependently, without combining values in anyway.1.3 The following safety hazards caveat pertains only to thetest methods portion, Section 14, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the use

5、rof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:3D996 Terminology of Packaging and Distribution Environ-mentsD1974 Practice for Methods of Closing, Sealing, and Rei

6、n-forcing Fiberboard BoxesD2860/D2860M Test Method for Adhesion of Pressure-Sensitive Tape to Fiberboard at 90 Angle and ConstantStressD3330/D3330M Test Method for Peel Adhesion ofPressure-Sensitive TapeD3611 Practice forAcceleratedAging of Pressure-SensitiveTapesD3652/D3652M Test Method for Thickne

7、ss of Pressure-Sensitive TapesD3654/D3654M Test Methods for Shear Adhesion ofPressure-Sensitive TapesD3715/D3715M Practice for Quality Assurance ofPressure-Sensitive TapesD3759/D3759M Test Method for Breaking Strength andElongation of Pressure-Sensitive TapeD3811/D3811M Test Method for Unwind Force

8、ofPressure-Sensitive TapesD3815/D3815M Practice for Accelerated Weathering ofPressure-Sensitive Tapes by Open-Flame Carbon-Arc Ex-posure ApparatusD3816/D3816M Test Method for Water Penetration Rate ofPressure-Sensitive TapesD3833/D3833M Test Method forWaterVaporTransmissionof Pressure-Sensitive Tape

9、sD3951 Practice for Commercial PackagingD4727/D4727M Specification for Corrugated and SolidFiberboard Sheet Stock (Container Grade) and Cut ShapesD5570 Test Method for Water Resistance of Tape andAdhesives Used as Box Closure2.2 TAPPI Standard:T 414 Internal Tear Resistance of Paper (Elmendorf-TypeM

10、ethod)42.3 Federal Specifications:PPP-T-60 Tape: Packaging, Waterproof5PPP-T-76 Tape, Packaging, Paper (for Carton Sealing)5PPP-T-680 Tape, Pressure-Sensitive Adhesion: Packagingand Packing of5FED-STD-595 Colors52.4 ISO Standard:ISO 9000:2000 Quality Management SystemsFundamen-tals and Vocabulary6IS

11、O 9001:2000 Quality Management SystemsRequire-ments6ISO 9004:2000 Quality Management SystemsGuidelines1This specification is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.14 on Tape andLabels.Current edition approved April 1, 2012. Publ

12、ished May 2012. Originallyapproved in 1993. Last previous edition approved in 2006 as D5486/D5486M 06.DOI: 10.1520/D5486_D5486M-06R12.2This specification is intended to replace Federal Specifications PPP-T-60 andPPP-T-76.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact

13、 ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Available from Technical Association of the Pulp and Paper Industry (TAPPI),15 Technology Parkway South, Norcross, GA 30092, http:/www.tapp

14、i.org.5Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.6Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.1Copyright ASTM International, 100 B

15、arr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.for Performance Improvements6NOTE 1The following is a comparison of types and classes of thisspecification compared with PPP-T-60 and PPP-T-76:D5486/D5486M PPP-T-60 PPP-T-76Type I Type III N/AClass 1 Class 1Class 2 Class

16、2Type II N/A N/AType III N/A N/AType IV Type IV N/AType V N/A Same3. Terminology3.1 Definitions:3.1.1 General definitions for packaging and distributionenvironments are found in Terminology D996.4. Significance and Use4.1 Type I is a polyester film-backed pressure-sensitive tapeintended for box clos

17、ure and sealing applications wherestrength and resistance to sunlight, rain, and other deterioratingelements are required. It is usually used on weather-resistantfiberboard (Class WR or WWVR of Specification D4727/D4727M). The tape is intended for H-type closure or sealing ofregular slotted boxes (C

18、losure Method 2B3 and 2B4 of PracticeD1974), and other applications where the tape will be over-lapped onto itself. Type I, Class 2 transparent tape can also beused for label attachment and covering applications whereweather resistance is needed.4.2 Type II is a polyester film-backed pressure-sensit

19、ivetape intended for box closure applications where strength andwater-resistance are required. It is usually used on domesticgrade fiberboard (Class D of Specification D4727/D4727M).The tape is most suited for center seam closure of regular orregular slatted boxes (Closure Method 2B4 of Practice D19

20、74)and other applications where the tape will not be overlappedonto itself. Type II, Class 2 tape is also used for labelattachment and covering applications where water resistance isdesired.4.3 Type III is a polypropylene film-backed pressure-sensitive tape intended for box closure applications wher

21、e ageneral purpose water-resistant tape is desired. It is used ondomestic grade fiberboard (Class D of Specification D4727/D4727M). The tape is suited for center seam closure of regularslotted boxes (Closure Method 2B4 of Practice D1974).4.4 Type IV is a woven cloth-backed pressure-sensitive tapefor

22、 less critical packaging applications where a cloth-backedtape is desired.4.5 Type V is a paper-backed weather-resistant, water-resistant pressure-sensitive tape for box closure and sealingapplications where weather resistance and water resistance arerequired. It may be used on weather-resistant or

23、domesticfiberboard (Classes WR, WWVR, and D of SpecificationD4727/D4727M). The tape is suited for center seam andH-type closures or sealing of regular slotted boxes (ClosureMethods 2B3, 2B4, and 2B7 of Practice D1974) and otherapplications where it may be overlapped onto itself.5. Classification5.1

24、Types and Classes:5.1.1 Type IWaterproof, weather-resistant, polyester-backed:5.1.1.1 Class 1Colored.5.1.1.2 Class 2Transparent.5.1.2 Type IIWater-resistant polyester backed.5.1.2.1 Class 1Tan.5.1.2.2 Class 2Transparent.5.1.3 Type IIIWater-resistant polypropylene.5.1.4 Type IVWater-resistant woven c

25、loth backed.5.1.5 Type VWeather-resistant paper backed.6. Ordering Information6.1 The inquiry or order shall include the following:6.1.1 ASTM Designation and date of issue;6.1.2 Type and Class required (see 5.1);6.1.3 Roll width and length (see 9.1);6.1.4 Color where applicable (see 10.1);6.1.5 When

26、 backing certification is required (see 17.1);6.1.6 When testing and inspection certification is required(see 17.2);6.1.7 Level of packaging and packing if other than commer-cial (see Section 18);6.1.8 For packaging and packing for shipments to the U.S.Government (see 18.2); and6.1.9 When core marki

27、ng is required (see 18.3).7. Materials and Manufacture7.1 The materials used in the construction of the tape shallbe such as to assure performance of the tape over thetemperature range from 65 to 160F 55 to 71C and shallconform to the requirements of this specification.7.2 Backing:7.2.1 Type I backi

28、ng shall be polyester film.7.2.2 Type II backing shall be a polyester film.7.2.3 Type III backing shall be a polypropylene film.7.2.4 Type IV backing shall be a woven cloth.7.2.5 Type V backing shall be a treated paper.7.3 AdhesiveThe adhesive shall be pressure-sensitivewater-insoluble and shall req

29、uire no moisture heat or otherpreparation prior to or after application to clean, dry surfaces.The adhesive shall be coated in a smooth and evenly distrib-uted layer on one side of the backing.7.4 RollsThe tape shall be evenly wound in rolls, adhe-sive side in, on cores made of paper-fiber or plasti

30、c. The coreshall have sufficient rigidity to prevent distortion of the rollunder normal conditions of transportation and use. The insidediameter of the core shall be 7.6, 0, + 1.6 mm 3, 0, +116in. When the roll is unwound, the backing shall not tear, theadhesive shall not transfer nor split from the

31、 face of the tapebacking to the adjacent layer before or after aging (see Table1).8. Physical Properties8.1 The tape shall comply with the physical property re-quirements listed in Table 2 and the water-solubility require-ment of Test Method D5570.D5486/D5486M 06 (2012)29. Dimensions, Mass, and Perm

32、issible Variations9.1 The width of the roll shall be 48 or 72 mm 2 or 3 in.or other commercially available widths, as specified (see6.1.3).9.1.1 A width tolerance of 1.5 mm 6116 in. shall beallowed on all widths.NOTE 2Uses of pressure-sensitive tapes in closure and sealing appli-cations call for com

33、monly available commercial widths. The widthscommon in the inch-pound system are not identical to the available SIreplacement widths. The most frequent width conversions are:Inch-Pound, in. SI, mm1241.5 3624837249NOTE 3The effect of this width difference on packaging performanceis not considered sig

34、nificant.79.2 Length:9.2.1 Types I, II, III, and IVThe length of the roll shall be50 or 55 m 55 or 60 yd, or other commercially availablelengths, as specified (see 6.1.3).9.2.2 Type VThe length of the roll shall be 100 m 120yd, or other commercially available length, as specified (see6.1.3).9.3 Spli

35、cesThe roll shall consist of a single length of tape,except any single roll of Types I, II, III, and IV may contain amaximum of one splice.Any single roll of Type V may containa maximum of four splices.9.3.1 Splices shall be such that they will not separate whenthe roll is unwound by hand or machine

36、 (see Table 1).10. Color10.1 Type I, Class 1 tape shall correspond reasonably inshade to the colors following gloss cards of FED-STD-595: red11136, olive drab 14087, dark green 14110, black 17038, andtan (no color card available for tan).10.2 Type II, Class 1 tape shall be tan in color.10.3 Type III

37、 color shall be as ordered in commerciallyavailable colors and transparent.10.4 Type IV tape shall correspond reasonably in shade tothe following lusterless color cards of FED-STD-595: red31116, olive drab X34087, dark green 34108, black 37038,white 37875 and tan 30450.10.5 Type V color shall be as

38、manufactured.10.6 Types I and II, Class 2 tapes shall be sufficiently clearand transparent to allow easy reading of 10-point type whentape is applied directly over printed matter.11. Workmanship, Finish, and Appearance11.1 The tape shall be uniformly constructed and free fromdefects that impair the

39、usefulness of the tape for the purposeintended (see Section 5). The tape adhesive coating shall beuniform, covering entirely one side of the tape. The edges shallbe clean, straight, and unbroken. The rolls shall be evenlywound. The finished product shall conform to the levels ofquality established h

40、erein.12. Sampling12.1 End Item ExaminationThe lot size for visual inspec-tion shall be in accordance with Practice D3715/D3715M.Sample size shall be one roll.12.2 End-Item Testing The lot size for end-item testingshall be in accordance with Practice D3715/D3715M. Theacceptable quality level (AQL) s

41、hall be 4.0 %.13. Specimen Preparation and Number of Tests13.1 Specimen preparation shall be as specified in theappropriate test method.13.2 Number of tests per unit of product shall be asspecified in the appropriate test method.13.3 First article of manufacture specimens shall consist ofat least fi

42、ve rolls of tape.14. Test Methods14.1 Responsibility for InspectionUnless otherwise speci-fied in the contract or order, the manufacturer is responsible forthe performance of all inspection requirements as specifiedherein.14.2 Responsibility for ComplianceAll items must meetall requirements of Secti

43、ons 7-18. The inspections set forth inthis specification shall become part of the manufacturersoverall inspection system or quality program for the contract ororder. The absence of any inspection requirement in thespecification shall not relieve the manufacturer of the respon-sibility of ensuring th

44、at all rolls of tape submitted for accep-tance comply with all the requirements of the contract or order.Sampling in quality conformance does not authorize submis-sion of known defective material, either indicated or actual, nordoes it commit the buyer to acceptance of defective material.14.3 Classi

45、fication of Inspections:14.3.1 First Article of ManufactureWhen a product is firstmanufactured in a plant, it shall be tested and inspected todetermine compliance with all examination and tests of thisspecification by an independent laboratory. First article ofmanufacture examinations need only be r

46、epeated when there isa change in materials, processes, or plant of manufacture.14.3.2 Quality Conformance InspectionsQuality confor-mance inspections shall consist of the following:14.3.2.1 Adhesion, as received,14.3.2.2 Shear adhesion to fiberboard at 73F, as received,7Supporting data have been fil

47、ed at ASTM International Headquarters and maybe obtained by requesting Research Report RR:D10-1004.TABLE 1 Test MethodsTest Method DesignationAdhesion, as Received and Aged D3330/D3330M Procedure AAdhesion to Fiberboard at 90Angle and Constant Stress D2860/D2860MProcedure AShear Adhesion D3654/D3654

48、M Procedure ABreak Strength D3759/D3759MTear Resistance TAPPI T414Thickness D3652/D3652MUnwind, As-Received and Aged D3811/D3811MWater-Penetration Rate D3816/D3816MWater-Solubility D5570Water-Vapor Transmission Rate D3833/D3833MWeathering, Types I and IV D3815/D3815MD5486/D5486M 06 (2012)314.3.2.3 S

49、hear adhesion to fiberboard at 150F, as received,14.3.2.4 Shear adhesion to steel at 150F. as received,14.3.2.5 Tear resistance,14.3.2.6 Break strength and elongation, and14.3.2.7 Unwind, as received.14.4 Test Methods:TABLE 2 Physical Property RequirementsNOTE 1N/A = not applicable.PropertyType I Type IIType III Type IV Type V Reference TestClass 1 Class 2 Class 1 Class 2Adhesion, minAs received (N/100 mm) 55 55 55 55 49 44 38 Table 1(oz/in.) 50 50 50 50 45 40 35Aged (N/100 mm) 49 49 49 49 49 33 38 Table 1 and(oz/in.) 45 45