ASTM D2911-2010 Standard Specification for Dimensions and Tolerances for Plastic Bottles《塑料瓶的尺寸和公差的标准规范》.pdf

《ASTM D2911-2010 Standard Specification for Dimensions and Tolerances for Plastic Bottles《塑料瓶的尺寸和公差的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D2911-2010 Standard Specification for Dimensions and Tolerances for Plastic Bottles《塑料瓶的尺寸和公差的标准规范》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D2911 10Standard Specification forDimensions and Tolerances for Plastic Bottles1This standard is issued under the fixed designation D2911; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A nu

2、mber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the thread configuration anddimensions for finishes for plastic bottles with screw-typeclosures, having a maxim

3、um capacity of 18.9 L (5 gal) and amaximum bottle dimension of 305 mm (12 in.). Included aretolerances for bottle capacity and body dimensions.1.2 The values stated in SI units are to be regarded as thestandard.1.3 The following precautionary caveat pertains only to thetest methods portion, Section

4、8 of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to u

5、se.NOTE 1There is no known ISO equivalent to this standard.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1898 Practice for Sampling of Plastics33. Terminology3.1 Definitions:3.1.1 bottle finishthe configuration of the neck or openingof the bottle whic

6、h serves to engage specific parts of theclosure in order to securely attach it to the bottle.3.1.2 bottle heightthe maximum dimension of a bottle ina plane perpendicular to the bottle base when the bottle issetting in its normal upright position.3.1.3 bottle thicknessthe smaller dimension in a plane

7、parallel to the bottle base.3.1.4 bottle widththe larger dimension in a plane parallelto the bottle base.4. Dimensions and Recommended Variations4.1 Recommended Variations in Overflow CapacityInoverflow capacity recommended variations of plastic bottles upto 18.9 L (5 gal) in size shall be in accord

8、ance with Table 1.4.2 Recommended Variations in Body DimensionsTherecommended variations in the body dimensions of plasticbottles covered by this specification shall be in accordance withTable 2.4.3 Finish Dimensions and DesignThe bottle finish di-mensions and design for the nine finishes covered by

9、 thisspecification shall be in accordance with Figs. 1-8 and Tables3-10.5. Sampling5.1 A batch or lot shall be considered as a unit of manufac-ture.5.2 Unless otherwise agreed upon between manufacturerand purchaser, the material shall be sampled in accordancewith the procedure described in Section 9

10、 of Practice D1898.Adequate statistical sampling prior to packaging shall beconsidered an acceptable alternative.6. Conditioning6.1 ConditioningCondition the test specimens at 23 62C (73.4 6 3.6F) and 50 6 5% relative humidity for not lessthan 40 h prior to test in accordance with Procedure A ofPrac

11、tice D618 for those tests where conditioning is required. Incases of disagreement, the tolerances shall be 6 1C (61.8F)and 62 % relative humidity.6.2 Test ConditionsConduct tests in the standard labora-tory atmosphere of 23 6 2C (73.4 6 3.6F) and 50 6 5%relative humidity, unless otherwise specified

12、in the test meth-ods or in this specification. In cases of disagreement, thetolerances shall be 61C (61.8F) and 62 % relative humid-ity.7. Apparatus7.1 For Determining Bottle Capacity:7.1.1 Balance, having an accuracy of 60.1 % or better atrated capacity (full scale).7.1.2 Pipet, Graduated Cylinder,

13、 and Beaker, as required.1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.19 on Molded andExtruded Products.Current edition approved July 1, 2010. Published September 2010. Originallyapproved in 1970. Last previous ed

14、ition approved in 2005 as D2911 - 94 (2005).DOI: 10.1520/D2911-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM web

15、site.3Withdrawn.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7.1.3 Conditioned water at 23 6 2.0C (73.46 3.6F)containing a wetting agent sufficient to flatten the meniscus andeliminate air bubbles.NOTE 2It is acceptable to use any

16、 liquid detergent as the wettingagent.7.1.4 Stop Watch.7.2 For Determining Finish and Body Dimensions:7.2.1 Micrometers, Vernier Height Gages, or Vernier Cali-pers with an accuracy of 60.025 mm (60.001 in.).7.2.2 Internal Micrometers or Telescoping Gages with anaccuracy of 60.025 mm (60.001 in.).7.2

17、.3 Commercial Scale, good quality calibrated in 1-mm or132-in. increments.8. Test Methods8.1 Bottle Capacity:8.1.1 Weigh the empty bottle and record the weight ingrams.8.1.2 Fill the bottle to overflow capacity with conditionedwater containing the wetting agent, adjusting the meniscus byuse of a pip

18、et, if necessary, until the meniscus is tangent to thetop of the finish surface. No more than 2 min shall be allowedfor filling the bottle and no additional water shall be added afterthe bottle is filled to overflow and free of air bubbles.8.1.3 If the time exceeds 2 min, discard the sample and star

19、tover.NOTE 3The capacity of the container is somewhat time-dependent inthat the force of the water in the container will cause the container sidesto bulge with time and additional water will be needed to adjust tooverflow capacity.8.1.4 Weigh the filled bottle and record the weight in grams.8.1.5 Ca

20、lculate the bottle volume as follows:BvmL! 5 Bf2 Be!/0.997where:Bv= volume of bottle, mL,Bf= weight of filled bottle, g,Be= weight of empty bottle, g, and0.997 = weight of water (g/mL) at 23 6 2.0C (73.4 63.6F).Bvfluid oz! 5 Bf2 Be!/29.50where: 29.50 = weight of water (g/fluid oz) at 23 6 2.0C(73.4

21、6 3.6F).8.1.6 Determine the volume in millilitres (fluid ounces) foreach test specimen.TABLE 1 Bottle Overflow Capacity Tolerances for Plastic BottlesFluid Ounces MillilitresBottle Overflow Capacity Tolerance (6) Bottle Overflow Capacity Tolerance (6)less than 0.75 0.05 less than 22 1.50.75 and less

22、 than 1.2 0.07 22 and less than 35 2.01.2 and less than 1.6 0.08 35 and less than 47 2.51.6 and less than 2.1 0.10 47 and less than 62 3.02.1 and less than 2.8 0.12 62 and less than 83 3.52.8 and less than 3.9 0.14 83 and less than 115 43.9 and less than 5.4 0.17 115 and less than 159 55.4 and less

23、than 7.4 0.20 159 and less than 218 67.4 and less than 9.8 0.24 218 and less than 289 79.8 and less than 13 0.30 289 and less than 384 913 and less than 18 0.37 384 and less than 531 1118 and less than 26 0.44 531 and less than 767 1326 and less than 37 0.51 767 and less than 1092 1537 and less than

24、 51 0.68 1092 and less than 1505 2051 and less than 72 0.81 1505 and less than 2125 2472 and less than 98 1.01 2125 and less than 2892 3098 and less than 119 1.30 2892 and less than 3512 38119 and less than 139 1.50 3512 and less than 4103 44139 and less than 160 1.80 4103 and less than 4723 53160 a

25、nd less than 180 2.00 4723 and less than 5313 59180 and less than 210 2.20 5313 and less than 6199 65210 to 5 gallons 1 % of capacity 6199 to 18.89 litres 1 % of capacityTABLE 2 Body Dimensional ToleranceRange of Specific Dimensions Height Dimensions Width and Depth Dimensionsin. mm in. mm in. mm0 u

26、p to but not including 1 0 to 25.40 0.030 0.76 0.030 0.761 up to but not including 2 25.40 to 50.80 0.030 0.76 0.050 1.272 up to but not including 4 50.80 to 101.60 0.050 1.27 0.060 1.524 up to but not including 6 101.60 to 152.40 0.050 1.27 0.080 2.036 up to but not including 8 152.40 to 203.20 0.0

27、60 1.52 0.090 2.298 up to but not including 10 203.20 to 254.00 0.060 1.52 0.110 2.7910 up to but not including 12 254.00 to 304.80 0.080 2.03 0.120 3.0512 up to but not including 15 304.80 to 381.00 0.090 2.29 0.150 3.8115 up to but not including 18 381.00 to 457.20 0.110 2.79 0.150 3.81D2911 102“L

28、” Style “M” StyleAll-Purpose Thread(Plastic or Metal Closures)Modified Buttress Thread(Plastic Closures)Threads/in. abc Threads/in. abc5 in. 0.120 0.060 0.051 5 in. 0.120 0.060 0.049mm 3.05 1.52 1.30 mm 3.05 1.52 1.246 in. 0.094 0.047 0.040 6 in. 0.094 0.047 0.039mm 2.39 1.19 1.02 mm 2.39 1.19 0.998

29、 in. 0.084 0.042 0.036 8 in. 0.084 0.042 0.035mm 2.13 1.07 0.91 mm 2.13 1.07 0.89Example Thread Nomenclature“L” Style: L28SP400“M” Style: M28SP400NOTE 1T and E dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by thecontainer sup

30、plier and container customer, as necessary.NOTE 2Dimension H is measured from the top of the finish to the point where diameter T, extended parallel to the centerline, intersects the beador shoulder.NOTE 3Contour of bead, undercut or shoulder is optional.NOTE 4Unless otherwise specified, I min appli

31、es to the full length of the opening.NOTE 5Concentricity of I min with respect to diameters T and E is not included. I min is specified for filler tube only.NOTE 6A minimum of 1 full turn of thread shall be maintained.NOTE 7Corresponding dimensions and finish details are shown in Table 3.NOTE 8Consi

32、deration must be given to the sealing surface width for the sealing system being used.NOTE 9Many child resistant closures, etc.FIG. 1 SP 400 Finish Thread Cross SectionsD2911 1038.1.7 Report the arithmetic average volume of the speci-mens tested as the bottle capacity of the batch or lot fromwhich t

33、he samples were chosen.8.2 Body Dimensions:8.2.1 Using a suitable micrometer, a vernier height gauge,or a scale, measure the height of the bottle.8.2.1.1 If the top of the finish is parallel to the base of thecontainer and the height must be measured from the top of thefinish, and a commercial scale

34、 is used, one method is to placethe bottle on a flat surface and a straightedge across the top ofthe bottle finish. Then measure the perpendicular distancebetween the straightedge and the surface upon which the bottleis setting. Make four measurements, each 90 apart, and use themaximum as the bottle

35、 height.8.2.2 Using a suitable micrometer or vernier caliper, mea-sure the width and thickness of the bottle.“L” Style “M” StyleAll-Purpose Thread(Plastic or Metal Closures)Modified Buttress Thread(Plastic Closures)Threads/in. abc Threads/in. abc6 in. 0.094 0.047 0.040 6 in. 0.094 0.047 0.039mm 2.39

36、 1.19 1.02 mm 2.39 1.19 0.998 in. 0.084 0.042 0.036 8 in. 0.084 0.042 0.035mm 2.13 1.07 0.91 mm 2.13 1.07 0.89Example Thread Nomenclature:“L” Style: L22SP410“M” Style: M22SP410NOTE 1Construction of neck from B to D must be held within the shaded area shown.NOTE 2A minimum of 112 turns of thread shal

37、l be maintained.NOTE 3Unless otherwise specified, I min applies to the full length of the opening.NOTE 4Concentricity of I min with respect to diameters T and E is not included. I min is specified for filler tube only.NOTE 5T and E dimensions are the average of two measurements across the major and

38、minor axis. The limits of ovality will be determined by thecontainer supplier and container customer, as necessary.NOTE 6Consideration must be given to the sealing surface width for the sealing system being used.NOTE 7When valve style closures are used with this finish, special consideration must be

39、 given to a specific controlled inside diameter. In addition,it is acceptable to vary the dimensions indicated with asterisk (*) to ensure adequate material for finishing the inside diameter.NOTE 8Corresponding dimensions and details shown in Table 4.FIG. 2 SP 410 Finish Thread Cross SectionsD2911 1

40、048.2.2.1 In the case of a rectangular container, use themidpoints of the sides as the measuring points.8.2.2.2 For a cylindrical container, make one measurementon the parting line and another measurement 90 from theparting line. Use the average of these two measurements as thecontainer width.(1) If

41、, because of the shape of the container, there is somequestion about where the measurements are to be taken,agreement shall be reached between the purchaser and theseller.“L” Style “M” StyleAll-Purpose Thread(Plastic or Metal Closures)Modified Buttress Thread(Plastic Closures)Threads/in. abcdfThread

42、s/in. abcdf6 in. 0.094 0.047 0.040 0.020 0.020 6 in. 0.094 0.047 0.039 0.030 0.030mm 2.39 1.19 1.02 0.51 0.51 mm 2.39 1.19 0.99 0.76 0.768 in. 0.084 0.042 0.036 0.020 0.020 8 in. 0.084 0.042 0.035 0.030 0.030mm 2.13 1.07 0.91 0.51 0.51 mm 2.13 1.07 0.89 0.76 0.7612 in. 0.045 0.030 0.011 0.015 0.005

43、12 in. 0.051 0.030 0.016 0.020 0.008mm 1.14 0.76 0.28 0.38 0.13 mm 1.29 0.76 0.41 0.51 0.22Example Thread Nomenclature:“L” Style: L22SP415“M” Style: M22SP415NOTE 1Construction of neck from B to D must be held within the shaded area shown.NOTE 2A minimum of 2 turns of thread shall be maintained.NOTE

44、3Unless otherwise specified, I min applies to the full length of the opening.NOTE 4Concentricity of I min with respect to diameters T and E is not included. I min is specified for filler tube only.NOTE 5T and E dimensions are the average of two measurements across the major and minor axis. The limit

45、s of ovality will be determined by thecontainer supplier and container customer, as necessary.NOTE 6Consideration must be given to the sealing surface width for the sealing system being used.NOTE 7When valve style closures are used with this finish, special consideration must be given to a specific

46、controlled inside diameter. In addition,it is acceptable to vary the dimensions indicated with asterisk (*) to ensure adequate material for finishing the inside diameter.NOTE 8Corresponding dimensions and finish details are shown in Table 5.FIG. 3 SP 415 Finish Thread Cross SectionsD2911 1058.3 Fini

47、sh DimensionsUsing suitable micrometers, ver-nier calipers, or telescoping gages, measure the finish dimen-sions of the bottle.9. Retest and Rejection9.1 If the results of any test do not conform to the require-ments of this specification, it is acceptable for retesting todetermine conformity to be

48、performed as agreed upon betweenthe purchaser and the seller.NOTE 1Contour of bead, undercut, or shoulder is optional.“L” Style “M” StyleAll-Purpose Thread (Plastic or Metal Closures) Modified Buttress Thread (Plastic Closures)Threads/in. ab Threads/in. abc12 in. 0.045 0.030 12 in. 0.051 0.030 0.016

49、mm 1.14 0.76 mm 1.29 0.76 0.4112 in. 0.045 0.030 12 in. 0.051 0.030 0.016mm 1.14 0.76 mm 1.29 0.76 0.41NOTE 2Example Thread Nomenclature“L” Style: L15SP425 or“ M” Style M15SP425NOTE 3Corresponding dimensions and finish details are shown in Table 6.FIG. 4 SP 425 Finish Thread Cross SectionsD2911 106*(See Footnote, e, Table 7 and Table 8)NOTE 1Construction of neck from B to D must be held within the shaded area shown.NOTE 2A minimum of 118 turns of thread shall be maintained.NOTE 3Unless otherwise specified, I mi