ASTM D2484-2006 Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating Tape《聚酯薄膜压敏电绝缘带的标准规范》.pdf
《ASTM D2484-2006 Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating Tape《聚酯薄膜压敏电绝缘带的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM D2484-2006 Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating Tape《聚酯薄膜压敏电绝缘带的标准规范》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D 2484 06An American National StandardStandard Specification forPolyester Film Pressure-Sensitive Electrical Insulating Tape1This standard is issued under the fixed designation D 2484; the number immediately following the designation indicates the year oforiginal adoption or, in the cas
2、e of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers electrical insulating tape con-sisting of a polyester plastic f
3、ilm coated on one side with apressure-sensitive adhesive.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parenthesis are provided forinformation only.NOTE 1This standard and IEC 6045432 and 3 are similar but notequivalent in all details.2. Referenced Document
4、s2.1 ASTM Standards:2D 876 Test Methods for Nonrigid Vinyl Chloride PolymerTubing Used for Electrical InsulationD 1000 Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applica-tionsD 1711 Terminology Relating to Electrical InsulationD 2305 Test Methods for
5、 Polymeric Films Used for Elec-trical Insulation2.2 IEC Standard:Publication 604543 Specifications for Pressure-SensitiveAdhesive Tapes for Electrical Purposes. Sheet 2: Require-ments for Polyester Film Tapes (PETP) with Thermoset-ting Adhesive. Sheet 3: Requirements for Polyester FilmTapes (PETP) w
6、ith Non-Thermosetting Adhesive33. Terminology3.1 Definitions For definitions of terms used in thisspecification, refer to Terminology D 1711.4. Classification4.1 This specification includes the requirements for fourtypes as follows:4.1.1 Type 1General-purpose tape, nominal thickness0.06 mm (0.0025 i
7、n.) and coated with a thermoplastic adhesivewhich is not chemically heat reactive.4.1.2 Type 2General-purpose tape, nominal thickness0.06 mm (0.0025 in.) and coated with a heat-reactive thermo-setting adhesive.4.1.3 Type 3General-purpose tape, nominal thickness0.09 mm (0.0035 in.) and coated with a
8、heat-reactive thermo-setting adhesive.4.1.4 Type 4General-purpose tape, nominal thickness0.025 mm (0.0010 in.) and coated with a heat-reactive ther-mosetting adhesive.5. Materials and Manufacture5.1 The polymer used as the backing shall be clear polyeth-ylene terephthalate sheet.5.2 The pressure-sen
9、sitive adhesive coating shall be freefrom lumps and bare spots. There shall be no adhesive transferwhen tape is unwound from the roll.5.3 Both transparent and colored tapes are available.5.3.1 Type 1Transparent.5.3.2 Types 2, 3, and 4Transparent and colors.6. Standard Rolls6.1 The standard widths an
10、d lengths shall be selected fromthe following:6.1.1 Widths:mm in. mm in.614 2278938 25 11212 30 1141558 38 1121934 50 2Widths greater than 50 mm (2 in.) shall be agreed uponbetween the purchaser and the seller.6.1.2 Lengths:mft33 10850 16455 18066 2166.2 Non-standard widths and lengths are permissib
11、le ifagreed upon between the purchaser and seller.1This specification is under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Insulating Materials and is the direct responsibility ofSubcommittee D09.07 on Flexible and Rigid Insulating Materials.Current edition approved Oct. 1, 20
12、06. Published October 2006. Originallyapproved in 1966. Last previous edition approved in 2000 as D 2484 00.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the stan
13、dards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD24842006STANDARDSPECIFICATIONFORPOLYESTERFILMPRESSURESENSITIVEELECTRICALINSULATINGTAPE 聚酯 薄膜 压敏电

链接地址:http://www.mydoc123.com/p-512931.html