ASTM D2466-2015 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings Schedule 40《聚氯乙烯 (PVC) 塑料管配件 (表单40) 的标准规格》.pdf

《ASTM D2466-2015 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings Schedule 40《聚氯乙烯 (PVC) 塑料管配件 (表单40) 的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM D2466-2015 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings Schedule 40《聚氯乙烯 (PVC) 塑料管配件 (表单40) 的标准规格》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D2466 13D2466 15Standard Specification forPoly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule401This standard is issued under the fixed designation D2466; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year

2、 of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification covers p

3、oly(vinyl chloride) (PVC) Schedule 40 pipe fittings. Included are requirements for materials,workmanship, dimensions, and burst pressure.NOTE 1Socket-type CPVC plastic pipe fittings, Schedule 40, which were formerly included in this standard, are now covered by Specification F438.1.2 The products co

4、vered by this specification are intended for use with the distribution of pressurized liquids only, which arechemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems withcompressed air or other compressed gases, some manufacturers do not

5、 allow pneumatic testing of their products. Consult withspecific product/component manufacturers for their specific testing procedures prior to pneumatic testing.NOTE 2Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious saftey hazards s

6、houlda system fail for any reason.1.3 Fitting such as unions, flanges, special plastic-to-metal transitions and appurtenances intended for use with PVC piping arecovered under specification F1970.1.4 The text of this specification references notes, footnotes, and appendixes which provide explanatory

7、 material. These notesand footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided

8、 for information only and are not considered standard.1.6 The following safety hazards caveat pertains only to the test method portion, Section 7, of this specification.This standarddoes not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of t

9、he user of thisstandard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1599 Test Method for Resistance to Short-Time Hydraulic P

10、ressure of Plastic Pipe, Tubing, and FittingsD1600 Terminology for Abbreviated Terms Relating to PlasticsD1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)CompoundsD2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fitti

11、ngsD2749 Symbols for Dimensions of Plastic Pipe FittingsF412 Terminology Relating to Plastic Piping SystemsF438 Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40F1498 Specification for Taper Pipe Threads 60 for Thermoplastic Pipe and FittingsF19

12、70 Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) orChlorinated Poly (Vinyl Chloride) (CPVC) Systems1 This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcom

13、mittee F17.10 on Fittings.Current edition approved Aug. 1, 2013March 1, 2015. Published September 2013July 2015. Originally approved in 1965. Last previous edition approved in 20062013 asD2466 06.D2466 13. DOI: 10.1520/D2466-13.10.1520/D2466-15.2 For referencedASTM standards, visit theASTM website,

14、www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of

15、what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered

16、the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States12.2 NSF Standards:Standard No. 14 for Plastic Piping Components and Related Materials3Standard No.

17、61 for Drinking Water Systems ComponentsHealth Effects33. Terminology3.1 GeneralDefinitions are in accordance with Terminology F412, and abbreviations are in accordance with TerminologyD1600, unless otherwise indicated. The abbreviation for poly(vinyl chloride) plastic is PVC.4. Classification4.1 Ge

18、neralThis specification covers Schedule 40 PVC pipe fittings, made from four PVC plastic compounds and intendedfor use with Iron Pipe Size (IPS) outside-diameter plastic pipe.4.1.1 Fittings covered by this specification are normally molded. In-line fittings, such as couplings, bushings, caps, nipple

19、s, etc.,shall be molded or machined from extruded stock.4.1.2 Fittings fabricated by welding are not included in this specification.5. Materials5.1 This specification covers PVC pipe fittings made from five PVC plastics as classified in Specification D1784.These are PVC12454, 12454, 13354, 11443, an

20、d 14333.5.2 CompoundThe PVC plastic compound shall meet the requirements of PVC 12454, 12454, 11443, or 14333, as describedin Specification D1784.NOTE 3Mechanical strength, heat resistance, flammability, and chemical resistance requirements are covered in Specification D1784.5.3 Rework MaterialThe m

21、anufacturers shall use only their own clean rework fitting material and the fittings produced shallmeet all the requirements of this specification.6. Requirements6.1 Dimensions and Tolerances:6.1.1 Fitting sockets inside diameters (waterways), minimum wall thicknesses, and dimensions shall be as sho

22、wn in Table 1,Table 2, and Table 3 when measured in accordance with Test Method D2122.6.1.2 When multistep reducer bushings are cored out, the inner socket shall be reinforced from the outer wall by a minimumof three ribs extending from the top of the inner socket to the deepest extremity of the cor

23、ing. The transition from D to DJ (Table3) shall be straight, tapered as shown, or radiused. A positive taper in the same direction of the taper in the socket on the outsidediameter of the bushing is optional (See XA/XB in Table 3). Any point measured along the outside diameter of the bushing(between

24、 points XA and XB) shall not fall below minimum pipe OD.6.1.3 The minimum wall thickness of fittings shall be 125 % of the minimum wall thickness of the corresponding size ofSchedule 40 pipe for which they are designed to be used, except that for the socket, the wall thickness shall be at least equa

25、l tothe minimum wall thickness of the corresponding size of Schedule 40 pipe. For any threaded fitting the minimum wall thicknessof the threaded portion shall be at least equal to the thickness of material under the thread root of threaded Schedule 80 pipe ofthe same size.6.1.4 The minimum inside di

26、ameter of the fittings shall be not less than the minimum specified inside diameter of thecorresponding size of Schedule 40 pipe. Any fitting having a male thread shall have an internal diameter not larger than Schedule80 pipe of the same size.6.1.5 Minimum dimensions have zero negative tolerance. T

27、olerances on other dimensions are shown in Table 1 and Table 3.6.2 ThreadsFor all fittings having taper pipe threads, threads shall conform to Specification F1498 and be gaged in accordancewith 8.4.6.3 Burst Pressure:6.3.1 The minimum burst strength of the fittings shall be not less than that calcul

28、ated for the size and wall thickness of the pipewith which it is to be used, when calculated from the following equation:S 5PDO 2t!/2t (1)where:S = hoop stress, psi (or MPa),P = internal pressure, psi (or MPa),DO = average outside diameter, in. (or mm), andt = minimum wall thickness, in. (or mm).3 A

29、vailable from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140.48113-0140, http:/www.nsf.org.D2466 152Fittings tested in accordance with 8.5 shall withstand the minimum burst pressure shown in Table 4.6.3.2 Pressures shown are minimum burst pressures and do not imply

30、rated working pressures. The burst pressure shall be usedonly as an indication of quality.7. Workmanship, Finish, and Appearance7.1 The fittings shall be homogeneous throughout and free of cracks, holes, foreign inclusions, or other defects.The fittings shallbe as uniform as commercially practicable

31、 in color, opacity, density, and other physical properties.8. Test Methods8.1 ConditioningCondition the test specimens at 73 6 3.6F (23 6 2C) and 50 6 5 %10 % relative humidity for not lessthan 40 h prior to test in accordance with Procedure A of Practice D618, for those tests where conditioning is

32、required.8.2 Test ConditionsConduct tests in the Standard Laboratory Atmosphere of 73 6 3.6F (23 6 2C) and 50 6 5 %10 %relative humidity, unless otherwise specified in the test methods or in this specification.TABLE 1 Tapered Sockets for PVC Pipe Fittings, Schedule 40, in.ANominalPipeSizeASocket Ent

33、rance DiameterBSocket Bottom Diameter CBSocketLength,minDCInsideDiameter,minWall Thickness, min MinOutsideDiameterof Hub, MEntrance, minDiameterToleranceonDiameterMaxOut-of-RoundDiameterToleranceonDiameterMaxOut-of-RoundE F EW EX, EZ18 0.417 0.004 0.016(0.41)0.401 0.004 0.016(0.41)0.500 0.225 0.068

34、0.085 0.526 164 16414 0.552 0.004 0.016(0.41)0.536 0.004 0.016(0.41)0.500 0.320 0.088 0.110 0.672 164 16438 0.687 0.004 0.016(0.41)0.671 0.004 0.016(0.41)0.594 0.449 0.091 0.114 0.821 132 13212 0.848 0.004 0.016(0.41)0.836 0.004 0.016(0.41)0.688 0.578 0.109 0.136 0.998 132 13234 1.058 0.004 0.020(0.

35、51)1.046 0.004 0.020(0.51)0.719 0.740 0.113 0.141 1.221 132 1321 1.325 0.005 0.020(0.51)1.310 0.005 0.020(0.51)0.875 0.990 0.133 0.166 1.504 116 116114 1.670 0.005 0.024(0.61)1.655 0.005 0.024(0.61)0.938 1.335 0.140 0.175 1.871 116 116112 1.912 0.006 0.024(0.61)1.894 0.006 0.024(0.61)1.094 1.564 0.1

36、45 0.181 2.127 116 1162 2.387 0.006 0.024(0.61)2.369 0.006 0.024(0.61)1.156 2.021 0.154 0.193 2.634 116 116212 2.889 0.007 0.030(0.76)2.868 0.007 0.030(0.76)1.750 2.414 0.203 0.254 3.170 332 183 3.516 0.008 0.030(0.76)3.492 0.008 0.030(0.76)1.875 3.008 0.216 0.270 3.841 332 18312 4.016 0.008 0.030(0

37、.76)3.992 0.008 0.030(0.76)2.000 3.486 0.226 0.283 4.374 332 184 4.518 0.009 0.030(0.76)4.491 0.009 0.030(0.76)2.000 3.961 0.237 0.296 4.907 332 185 5.583 0.010 0.060(1.52)5.553 0.010 0.060(1.52)3.000 4.975 0.258 0.323 6.039 332 186 6.647 0.011 0.060(1.52)6.614 0.011 0.060(1.52)3.000 5.986 0.280 0.3

38、50 7.203 18 3168 8.655 0.015 0.090(2.29)8.610 0.015 0.090(2.29)4.000 7.888 0.322 0.403 9.320 18 31610 10.780 0.015 0.100(3.05)10.735 0.015 0.100(3.05)5.000 9.917 0.365 0.456 11.614 18 31612 12.780 0.015 0.120(3.81)12.735 0.015 0.120(3.81)6.000 11.825 0.406 0.508 13.786 18 316A The sketches and desig

39、ns of fittings are illustrative only.BSocket depth, measured from socket entrance face to socket bottom face.C See 6.1.4.D2466 1538.3 SamplingA sufficient quantity of fittings as agreed upon between the seller and the purchaser shall be selected at randomfrom each lot or shipment and tested to deter

40、mine that the basic design is in conformance with this specification.NOTE 4For individual orders or specifications, only those tests and numbers of tests specifically agreed upon between the purchaser and the sellerneed be conducted.8.4 ThreadsAll taper pipe threads shall be gaged in accordance with

41、 Specification F1498.8.5 Burst PressureDetermine the minimum burst pressure in accordance with Test Method D1599. The pressure shall beapplied at a uniform rate such that the minimum allowable burst pressure is attained in 60 or 70 s.NOTE 5The time-to-failure may exceed 70 s.8.5.1 ApparatusFittings

42、shall be tested while held in a test jig constructed in such a manner as to seal the socket by meansof O-rings, or gaskets but not to reinforce or support the fittings, except where contact is necessary because of the shape of thefitting to keep the fitting in the test jig. Such contact shall be hel

43、d to the minimum. The socket plug portion of the test fixture mustextend one third to two thirds of the socket depth. Failure of any part of the test apparatus does not constitute failure of the fittings.9. Retest and Rejection9.1 If the results of any test(s) do not meet the requirements of this sp

44、ecification, the tests(s) shall be conducted again only byagreement between the purchaser and seller. Under such agreement, minimum requirements shall not be lowered, changed, ormodified, nor shall specification limits be changed. If upon retest, failure occurs, the quantity of product represented b

45、y the test(s)does not meet the requirements of this specification.10. Marking10.1 Fittings shall be marked with the following:10.1.1 Manufacturers name or trademark,TABLE 2 Minimum Dimension from Center to End of Sockets(Laying Length) for Couplings, Tees, 90 and 45 Elbows, PVCSocket-Type Pipe Fitti

46、ngs, Schedule 40, in.ANominalPipe SizeG, min J, min N, min18 14 18 11614 516 532 11638 38 316 33212 12 14 33234 916 516 3321 1116 516 332114 78 38 332112 1 716 3322 114 58 332212 112 1116 3163 11316 34 316312 218 1 3164 2516 1 3165 3 138 3166 312 134 148 412 2 1410 51316 2916 1412 61516 3116 14A The

47、 sketches and designs of fittings are illustrative only.D2466 15410.1.2 Material designation PVC I for PVC 12454-B, PVC 12 for PVC 12454-C, PVC 13 for PVC 13354-C and 11443-B, andPVC II for PVC 14333-D,TABLE 3 Dimensions of Reducer Bushings, PVC Socket-Type Pipe Fittings, Schedule 40,A in. (mm)Nomin

48、al Size Outside DiameterXATolerance onOutside DiameterOutside DiameterXBTolerance onOutside DiameterMaximum Out-of-Roundness(max, minus min.)14 by 18 0.540 (13.72) +0.007 0.004 (0.18 0.10) 0.540 (13.72) 0.004 (0.10) 0.016 (0.41)38 by 14, 18 0.675 (17.41) +0.007 0.004 (0.18 0.10) 0.675 (17.41) 0.004

49、(0.10) 0.016 (0.41)12 by 38, 14 0.840 (21.34) +0.007 0.004 (0.18 0.10) 0.840 (21.34) 0.004 (0.10) 0.016 (0.41)34 by 12, 38, 14 1.050 (26.67) +0.007 0.004 (0.18 0.10) 1.050 (26.67) 0.004 (0.10) 0.020 (0.51)1 by 12, 34 1.315 (33.40) +0.008 0.005 (0.20 0.13) 1.315 (33.40) 0.005 (0.13) 0.020 (0.51)114 by 12, 34, 1 1.660 (42.16) +0.008 0.005 (0.20 0.13) 1.660 (42.16) 0.0