ASTM D2397 D2397M-2013 Standard Specification for Cationic Emulsified Asphalt《阳离子乳化沥青标准规格》.pdf

《ASTM D2397 D2397M-2013 Standard Specification for Cationic Emulsified Asphalt《阳离子乳化沥青标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM D2397 D2397M-2013 Standard Specification for Cationic Emulsified Asphalt《阳离子乳化沥青标准规格》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D2397/D2397M 13Standard Specification forCationic Emulsified Asphalt1This standard is issued under the fixed designation D2397/D2397M; the number immediately following the designation indicates theyear of original adoption or, in the case of revision, the year of last revision. A number

2、 in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This specification covers seven grades of cationic emul

3、-sified asphalt for use in pavement construction in the mannerdesignated.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other

4、. Combiningvalues from the two systems may result in non-conformancewith the standard.2. Referenced Documents2.1 ASTM Standards:2D5 Test Method for Penetration of Bituminous MaterialsD113 Test Method for Ductility of Bituminous MaterialsD140 Practice for Sampling Bituminous MaterialsD244 Test Method

5、s and Practices for Emulsified AsphaltsD2042 Test Method for Solubility of Asphalt Materials inTrichloroethyleneD3910 Practices for Design, Testing, and Construction ofSlurry SealD6930 Test Method for Settlement and Storage Stability ofEmulsified AsphaltsD6933 Test Method for Oversized Particles in

6、EmulsifiedAsphalts (Sieve Test)D6935 Test Method for Determining Cement Mixing ofEmulsified AsphaltD6936 Test Method for Determining Demulsibility of Emul-sified AsphaltD6997 Test Method for Distillation of Emulsified AsphaltD7226 Test Method for Determining the Viscosity of Emul-sified Asphalts Usi

7、ng a Rotational Paddle ViscometerD7402 Practice for Identifying Cationic Emulsified AsphaltsD7496 Test Method for Viscosity of Emulsified Asphalt bySaybolt Furol ViscometerD7553 Test Method for Solubility of Asphalt Materials inN-Propyl Bromide3. Requirements3.1 The emulsified asphalt shall be teste

8、d within 14 days ofdelivery. The emulsified asphalt shall be homogeneous afterthorough mixing provided separation has not been caused byfreezing. Emulsions separated by freezing shall not be tested.3.2 Emulsified asphalt shall conform to the requirementsprescribed in Table 1 or Table 2. If no table

9、is specified, thedefault is Table 1.4. Sampling4.1 Samples of emulsified asphalt shall be taken in accor-dance with Practice D140.4.2 Samples shall be stored in clean, airtight sealed contain-ers at a temperature of not less than 4C 39.2F until tested.5. Test Methods5.1 The properties of the emulsif

10、ied asphalts given in Table1 or Table 2 shall be determined in accordance with thefollowing ASTM test methods:5.1.1 ViscosityTest Method D7496 for Table 1 or TestMethod D7226 for Table 2.5.1.2 Storage StabilityTest Method D6930.5.1.3 DemulsibilityTest Method D6936.5.1.4 Coating Ability and Water Res

11、istanceTest MethodsD244.5.1.5 Particle ChargeTest Method D7402.5.1.6 Sieve TestTest Method D6933, except use distilledwater in all wetting and washing operations in place of thenonionic surfactant solution (1 %).5.1.7 Cement MixingTest Method D6935.5.1.8 DistillationTest Method D6997.5.1.9 Tests on

12、Residue from DistillationTest Methods D5,D113, D2042, and D7553.1This specification is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.41 onEmulsified Asphalt Specifications.Current edition approved Dec. 1, 2013. Published

13、 January 2014. Originallyapproved in 1965. Last previous edition approved in 2012 as D2397 12. DOI:10.1520/D2397_D2397M-13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, re

14、fer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1TABLE1RequirementsforCationicEmulsifiedAsphaltTypeRapid-SettingMedium-SettingSlow-SettingQuickSettingGradeCRS-1CRS-2CMS-2CMS

15、-2hCSS-1CSS-1hCQS-1hAminmaxminmaxminmaxminmaxminmaxminmaxminmaxTestonemulsions:Viscosity,SayboltFurolat25C77FSFS201002010020100Viscosity,SayboltFurolat50C122FSFS201001004005045050450Storagestabilitytest,24-h,%B111111Demulsibility,35mL,0.8%dioctylsodiumsulfosuccinate,%40.40.Coatingabilityandwaterresi

16、stance:Coating,dryaggregateCoating,aftersprayingCoating,wetaggregategood fair fairgood fair fairCoating,aftersprayingfairfairParticlechargetestpositivepositivepositivepositivepositivepositivepositiveSievetest,%B0.100.100.100.100.100.100.10Cementmixingtest,%2.02.0N/ADistillation:Oildistillate,byvolum

17、eofemulsion,%331212Residue,%60656565575757Testsonresiduefromdistillationtest:Penetration,25C77F,100g,5s100250100250100250409010025040904090Ductility,25C77F,5cm/min,cm40404040404040Solubilityintrichloroethylene,orN-PropylBromide%97.597.597.597.597.597.597.5ACQS-1hisusedforQuickSetSlurrySealsystems.CQ

18、S-1hemulsifiedasphaltsshallmeettherequirementsoutlinedinPracticesD3910.BThistestrequirementonrepresentativesamplesiswaivedifsuccessfulapplicationofthematerialhasbeenachievedinthefield.D2397/D2397M 132TABLE2RequirementsforCationicEmulsifiedAsphaltTypeRapid-SettingMedium-SettingSlow-SettingQuickSettin

19、gGradeCRS-1CRS-2CMS-2CMS-2hCSS-1CSS-1hCQS-1hAminmaxminmaxminmaxminmaxminmaxminmaxminmaxTestonemulsions:Viscosity,RotationalPaddleViscometerat25C77FmPas452204522045220Viscosity,RotationalPaddleViscometerat50C122FmPas45220220880110990110990Storagestabilitytest,24-h,%B111111Demulsibility,35mL,0.8%dioct

20、ylsodiumsulfosuccinate,%40.40.Coatingabilityandwaterresistance:Coating,dryaggregateCoating,aftersprayingCoating,wetaggregategood fair fairgood fair fairCoating,aftersprayingfairfairParticlechargetestpositivepositivepositivepositivepositivepositivepositiveSievetest,%B0.100.100.100.100.100.100.10Cemen

21、tmixingtest,%2.02.0N/ADistillation:Oildistillate,byvolumeofemulsion,%331212Residue,%60656565575757Testsonresiduefromdistillationtest:Penetration,25C77F,100g,5s100250100250100250409010025040904090Ductility,25C77F,5cm/min,cm40404040404040Solubilityintrichloroethylene,orN-PropylBromide%97.597.597.597.5

22、97.597.597.5ACQS-1hisusedforQuickSetSlurrySealsystems.CQS-1hemulsifiedasphaltsshallmeettherequirementsoutlinedinPracticesD3910.BThistestrequirementonrepresentativesamplesiswaivedifsuccessfulapplicationofthematerialhasbeenachievedinthefield.D2397/D2397M 1336. Keywords6.1 cationic; emulsified asphalt;

23、 emulsion; medium setting;rapid setting; slow settingASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent ri

24、ghts, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either fo

25、r revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearin

26、g you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard ma

27、y be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D2397/D2397M 134