ASTM C223-1998(2003)e1 Standard Specification for Asbestos-Cement Siding《石棉水泥板壁标准规范》.pdf

《ASTM C223-1998(2003)e1 Standard Specification for Asbestos-Cement Siding《石棉水泥板壁标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM C223-1998(2003)e1 Standard Specification for Asbestos-Cement Siding《石棉水泥板壁标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C 223 98 (Reapproved 2003)e1Standard Specification forAsbestos-Cement Siding1This standard is issued under the fixed designation C 223; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numbe

2、r in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.e1NOTEAsbestos warning editorially added in February 2005.1. Scope1.1

3、This specification covers asbestos-cement siding, in-cluding accessories, designed to provide the weather-exposedsidewall surfaces of buildings. Siding in the following forms iscovered:1.1.1 Siding ShinglesUniform thickness, generally rectan-gular in shape and having wavy, random, thatched, straight

4、, orirregular butts.1.1.2 ClapboardsUniform thickness, generally longer andnarrower in shape than siding shingles, and usually with theexposed edge straight.1.1.3 SheetsUniform thickness, rectangular in shape,larger in unit sizes than shingles or clapboards.NOTE 1For additional information, see Spec

5、ification C 725 for Semi-dense Mineral Fiber Siding.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 WarningBreathing of asbestos dust is hazardous.Asbestos and asbestos products present demonstrated healthrisks for user

6、s and for those with whom they come into contact.In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For informa-tion on the safe use of chrysotile asbestos, refer to “Safe Use ofChrysotile: A Manual on Preventive and Control Measures.”22. Re

7、ferenced Documents2.1 ASTM Standards:3C 220 Specification for Flat Asbestos-Cement SheetsC 458 Test Method for Organic Fiber Content of Asbestos-Cement ProductsC 459 Test Methods for Asbestos-Cement Flat ProductsC 725 Specification for Semidense Mineral Fiber SidingC 1096 Test Method for Determinati

8、on of Wood Fiber inAsbestos Cement2.2 Federal Standard:4Fed. Std. No. 123 Marking for Domestic Shipment (CivilianAgencies)2.3 Military Standard:4MIL-STD-129 Marking for Shipment and Storage2.4 Other Documents:Uniform Freight Classification Rules5National Motor Freight Classification Rules63. Physica

9、l Requirements3.1 All measurements and tests necessary for determiningthe conformity of the asbestos-cement siding with this speci-fication shall be made in accordance with Test Methods C 459.3.2 Flexural StrengthThe average breaking load obtainedby loading equally and simultaneously at both one-thi

10、rd pointsof the test span as shown in Table 1.3.3 DeflectionThe average deflection at mid-span atmaximum load obtained by loading equally and simulta-neously at both one-third points of the test span as shown inTable 1.3.4 Water AbsorptionThe average water absorption shallnot exceed 30 % mass.4. Dim

11、ensions, Mass, and Permissible Variations4.1 Asbestos-cement siding supplied under this specifica-tion shall conform to the dimensions prescribed in Table 2.4.2 The unit dimensions and laps given in Table 2 are anindication of customary current manufacture and shall not be1This specification is unde

12、r the jurisdiction of ASTM Committee C-17 onFiber-Cement Products and is the direct responsibility of Subcommittee C17.03 onAsbestos-Cement Sheet Products and Accessories.Current edition approved Sept. 10, 1998. Published March 1999. Originallypublished as C 223 49. Last previous edition C 223 91(19

13、95)e1.2Available from The Asbestos Institute, http:/ referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Available fr

14、om Standardization Documents, Order Desk, Bldg. 4, Section D,700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.5Available from The Uniform Classification Commission, Room 1106, 222 S.Riverside Plaza, Chicago, IL 60606.6Available from National Motor Freight Inc., 1616 P. St., N.W., Washingto

15、n, DC20036.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.construed to limit or fix the width, length, or lap dimensions ofsiding units that conform to all other requirements of thisspecification. Siding units of one half normal len

16、gth may besupplied in an amount not exceeding two per bundle. Fifteenpercent of the clapboard units may be supplied shorter than thestandard length in multiples of 406 mm (16 in.).4.3 ThicknessThe average thickness of all units suppliedunder this specification shall be as shown in Table 1, and theav

17、erage thickness of any one unit shall not be less than theaverage of all units within the shipment by more than 10 %.For textured siding, the thickness shall be construed as thegross over-all measurement from the top of the textured surfaceto the back of the unit.4.4 Width and LengthThe permissible

18、variation from thenominal width or length shall be 3.2 mm (618 in.), asmeasured after 48 h at 23C (73F) and 50 % relative humidity.5. Workmanship, Finish, and Appearance5.1 WorkmanshipThe surface of the siding to be exposedshall be free of defects that impair appearance or serviceability.5.2 FinishT

19、he exposed surface of the siding may besmooth, grained, granuled, coated, or otherwise textured.5.3 ColorThe exposed surface of the siding may benatural color of the asbestos-cement product or may be coloredby the addition of mineral pigments, chemical impregnation,pigmented coatings, veneers, or em

20、bedded mineral granules.5.4 Holes for Nails and FastenersUnless otherwise speci-fied for special application methods, holes for nails andfasteners shall be provided and shall be so placed as to satisfythe top lap requirements given in Table 2.5.5 EfflorescenceEfflorescence that sometimes may ap-pear

21、 on asbestos-cement siding is not a defect and should notresult in a permanent change in color.6. Nails and Fasteners6.1 Face nails shall have small, flat heads with shanks sizedto enter the face nail holes provided in the units. They shall belong enough to hold the siding units securely to a wood l

22、umbernailing base, and be of nonstaining, corrosion-resistant mate-rial. Face nails shall be furnished with the siding by themanufacturer.6.2 Special fasteners for attaching siding units to other thana wood lumber nailing base must be purchased separately andare not furnished with the siding. Fasten

23、ers of this type shall beof the nonstaining corrosion-resistant type.6.3 Baker strips in sufficient quantity and proper size forflashing the vertical joining between siding units shall befurnished by the manufacturer with the siding. These stripsshould be made of an asphalt-(not coal tar-)saturated

24、andcoated material. Joint flashing materials are not furnished withsheets used for siding and must be purchased separately.7. Underlayment Sheet7.1 Underlayment sheet material for use in the applicationof asbestos-cement siding is not furnished, but must bepurchased separately.7.2 Asphalt-saturated

25、felt is suitable for underlayment use.Coal tar-saturated felt is not suitable. The felt shall weigh notless than 63.5 kg/100 m2(13 lb/100 ft2). Underlayment sheetmaterial for use with asbestos-cement siding shall be water-resistant and of the “breather” type, permeable to water vapor.8. Composition

26、Requirements8.1 Asbestos-cement siding shall be composed of a combi-nation of asbestos fiber and portland cement or portlandblast-furnace slag cement, and not more than 1 weight % oforganic fiber, (as determined by Test Methods C 458 orC 1096), with or without the addition of curing agents, water-re

27、pellent substances, mineral fillers, coatings, pigments, ormineral granules, formed under pressure and cured to meet thephysical requirements of this specification.9. Rejection and Retesting9.1 If the sample fails to conform to any one of therequirements of this specification, a second sample from t

28、hesame lot shall be prepared and tested. The results of the retestshall be averaged with the results of the original test todetermine compliance with this specification.9.2 Failure to conform to any one of the requirements of thisspecification, upon retest as prescribed above, shall constituteground

29、s for rejection. In case of rejection, the seller shall havethe right to reinspect the rejected shipment and resubmit the lotafter removal of the portion of the shipment not conforming tothe specified requirements, provided this is done within 20days after receipt of notice of the specific cause for

30、 rejection.10. Inspection10.1 Inspection of material shall be made at the point ofshipment. The inspector representing the purchaser shall havefree access to the carriers being loaded for shipment to thepurchaser. He shall be afforded all reasonable and availablefacilities at the point of shipment f

31、or sampling and inspectionof the material, which shall be so conducted as not to interfereunnecessarily with the loading of the carriers.TABLE 1 Typical Dimensions of Asbestos-Cement Sidingmm (in.)Type Width Minimum Top LapASiding shingles 200 to 405(8 to 16)610 to 1220(24to48)25 (1)Clapboards 200 t

32、o 405(8 to 16)1220 to 2440(48to96)25 (1)SheetsB405 to 1220(16to48)1220 to 3660(48 to 144)25 (1) unlessflashedATop lap is defined as the shortest distance between the lower edge of a courseof siding and the most proximate area of side wall not covered by the precedingcourse.BFlat sheets are also cove

33、red by Specification C 220.TABLE 2 Physical RequirementsThickness Minimum Breaking LoadMinimumDeflectionNominal MinimumStrongerDirectionWeakerDirectionmm (in.) mm (in.) N (lbf) N (lbf) mm (in.)4.5316 4.1 0.16 210 47 170 38 7 0.25614 5.7 0.22 370 83 310 70 5 0.21038 8.8 0.34 690 155 570 128 2.5 0.1C

34、223 98 (2003)e1211. Packaging and Shipping11.1 Commercial QuantitiesThe commercial unit is ap-proximately one square for marketing asbestos-cement siding.One square is sufficient material to cover 9.29 m2(100 ft2)ofwall area when applied according to the manufacturers direc-tions.11.2 Commercial Pac

35、kagingUnless otherwise specified,asbestos-cement siding shall be packaged in accordance withaccepted commercial practice, to ensure acceptance by com-mon carrier.11.3 Job ProtectionPackages of asbestos-cement sidingshall be stacked upon a raised, rigid, flat supporting base, andto avoid discoloratio

36、n shall be kept completely covered,protected from the weather, clean and dry, until applied.12. Keywords12.1 asbestos; asbestos-cement; asbestos-cement siding;clapboard; sheeting; sheets; shingles; siding; siding shinglesSUPPLEMENTARY REQUIREMENTSThe following supplementary requirements shall apply

37、when material is supplied under thisspecification for U.S. Government procurement.S1. PackagingS1.1 Unless otherwise specified in the contract, the materialshall be packaged in accordance with the producers standardpractice which will be acceptable to the carrier at lowest rates.Containers and packi

38、ng shall comply with Uniform FreightClassification Rules or National Motor Freight ClassificationRules. Marking for shipment of such material shall be inaccordance with Fed. Std. No. 123 for civil agencies andMIL-STD-129 for military agencies.S2. Responsibility for InspectionS2.1 Unless otherwise sp

39、ecified in the contract or purchaseorder, the producer is responsible for the testing of all materialto assure compliance with the test requirements specifiedherein. Except as otherwise specified in the contract or order,the producer may use his own or any other suitable facilities forthe performanc

40、e of the inspection and test requirements speci-fied herein, unless disapproved by the purchaser. The purchasershall have the right to perform any of the inspections and testsset forth in this specification where such inspections aredeemed necessary to assure that material conforms to pre-scribed re

41、quirements.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such

42、rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additio

43、nal standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the A

44、STM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).C 223 98 (2003)e13