ASTM C1311-2014 Standard Specification for Solvent Release Sealants《溶剂释放密封剂的标准规格》.pdf
《ASTM C1311-2014 Standard Specification for Solvent Release Sealants《溶剂释放密封剂的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM C1311-2014 Standard Specification for Solvent Release Sealants《溶剂释放密封剂的标准规格》.pdf(2页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: C1311 14Standard Specification forSolvent Release Sealants1This standard is issued under the fixed designation C1311; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses i
2、ndicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification describes the properties of a one-component solvent release sealant for use in building construc-tion. These sealants are generally formula
3、ted to withstand amaximum joint movement of 7.5 % in extension and 7.5 % incompression of the nominal joint width.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 The committee with jurisdiction of this specification isn
4、ot aware of any similar specification within ISO or any otherorganization.2. Referenced Documents2.1 ASTM Standards:2C661 Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a DurometerC712 Test Method for Bubbling of One-Part, Elastomeric,Solvent-Release Type SealantsC717
5、Terminology of Building Seals and SealantsC1193 Guide for Use of Joint SealantsC1216 Test Method for Adhesion and Cohesion of One-PartElastomeric Solvent Release SealantsC1257 Test Method for Accelerated Weathering of Solvent-Release-Type SealantsC1442 Practice for Conducting Tests on Sealants Using
6、Artificial Weathering ApparatusD2202 Test Method for Slump of SealantsD2203 Test Method for Staining from SealantsD2377 Test Method for Tack-Free Time of Caulking Com-pounds and SealantsD2452 Test Method for Extrudability of Oil- and Resin-BaseCaulking Compounds3. Terminology3.1 DefinitionsDefinitio
7、ns of the following terms used inthis specification are found in Terminology C717: adhesivefailure (adhesion loss), caulk (v), compound, durometer,hardness, joint, primer, seal, sealant, sealing material, solventrelease sealant, and standard conditions.4. Materials and Manufacture4.1 The sealing com
8、pound shall be a solvent release mate-rial compounded to conform to the requirements prescribed inthis specification.4.2 All material and workmanship shall be in accordancewith good commercial practice. The producer is permitted awide latitude in choice of raw materials for making theseproducts. Con
9、sequently, there is no implication that the com-pounds are equivalent in all physical properties.4.3 The manufacturing process shall be such as will ensurea homogeneous mix, free of defects that would affectserviceability, and of a consistency suitable for immediateapplication.5. General Requirement
10、s5.1 Standard ConditionsPerform all of the tests in acontrolled environment at standard conditions. Condition seal-ant samples for at least5hatthese conditions before any testsare performed.5.2 The sealant in the original container shall be suitable foruse for at least 12 months from the date of man
11、ufacture whenstored at a temperature neither below 5C (41.0F) norexceeding 27C (80.6F).5.3 The color of the sealant shall be as agreed upon betweenthe purchaser and the manufacturer.5.4 The sealant shall be intended for use only on clean, drysurfaces. When a primer is recommended by a manufacturerfo
12、r a specific substrate, all tests on that substrate shall includethe primer. The proper use of primers (or surface conditioners)with the application of sealants is described in detail in GuideC1193. This guide also describes proper methods for jointdesign, backup materials, surface preparation, tool
13、ing ofsealant, and other important procedures in sealant applicationin buildings.1This specification is under the jurisdiction of ASTM Committee C24 onBuilding Seals and Sealants and is the direct responsibility of Subcommittee C24.10on Specifications, Guides and Practices.Current edition approved J
14、une 1, 2014. Published July 2014. Originally approvedin 1995. Last previous edition approved in 2010 as C131110. DOI: 10.1520/C1311-14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume inf
15、ormation, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16. Significance and Use6.1 This specification describes solvent release sealants forgeneral caulking and sealing
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMC13112014STANDARDSPECIFICATIONFORSOLVENTRELEASESEALANTS 溶剂 释放 密封剂 标准 规格 PDF

链接地址:http://www.mydoc123.com/p-464181.html