ASTM B630-1988(2010) Standard Practice for Preparation of Chromium for Electroplating with Chromium《电镀用铬的制备的标准实施规程》.pdf
《ASTM B630-1988(2010) Standard Practice for Preparation of Chromium for Electroplating with Chromium《电镀用铬的制备的标准实施规程》.pdf》由会员分享,可在线阅读,更多相关《ASTM B630-1988(2010) Standard Practice for Preparation of Chromium for Electroplating with Chromium《电镀用铬的制备的标准实施规程》.pdf(2页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B630 88 (Reapproved 2010)Standard Practice forPreparation of Chromium for Electroplating with Chromium1This standard is issued under the fixed designation B630; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year
2、of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice is intended to serve as a process guide (notas a standard procedure) for producing adherent electrode
3、positsof chromium on chromium for engineering use.1.2 Only well-known, generally practical methods usinghexavalent chromium plating baths have been included. Someof the newer proprietary chromium plating processes producechromium plating for which this process is unsuitable. Suppli-ers of the proces
4、ses should be consulted.1.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this st
5、andard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B177 Guide for Engineering Chromium Electroplating3. Significance and Use3.1 Electrodeposits of chromium on chromium are pro
6、ducedin cases where it is desired to obtain a better performingcoating, to reclaim plated parts that are defective, or restoreworn chromium coatings to original dimensions.4. Preparation of Surface4.1 Surface FinishingThe smoothness of the chromiumcoating before electroplating with chromium should c
7、loselyapproximate the requirements of the finished part. It is usuallyachieved by appropriate grinding with a diamond wheel.4.2 Stripping and Basis MetalWith previously electro-plated parts where the chromium deposit has been wornthrough, or where grinding has exposed the basis metal,preferred resul
8、ts are obtained by stripping the remainingchromium completely. However, it is possible to obtain satis-factory deposits on such substrates by careful attention todetails in the pretreatment and electroplating process steps.4.3 Stripping may be done by several methods, includingproprietary processes
9、or inhibited hydrochloric acid solution(10 to 20 % by volume), or anodic treatment at 55 to 800 A/m2(5 to 75 A/ft2) in a solution of 35 to 50 g/L (5 to 7 oz/gal) ofsodium hydroxide or 60 to 75 g/L (8 to 10 oz/gal) of sodiumcarbonate at 20 to 25C (70 to 80F).4.4 Process Outline:4.4.1 Preclean (see 5.
10、1.1 and 5.1.2),4.4.2 Alkaline electrolytic clean (see 5.1.3),4.4.3 Rinse (cold water),4.4.3.1 Rinse (hot water),4.4.3.2 Dry,4.4.3.3 Mask (see 5.2),4.4.4 Activate (see 5.3),4.4.5 Chromium electroplate,4.4.6 Rinse (cold water),4.4.7 Rinse (hot water), and4.4.8 Dry.5. Procedure5.1 CleaningThe following
11、 cleaning treatments may beused for all conditions and types of electrodeposited chro-mium. The choice of the procedures will be governed largelyby the condition of the surface.5.1.1 PrecleaningWhen considerable amounts of greaseand oil are present on the surface, precleaning (emulsion oralkaline sp
12、ray or soak) is necessary to remove the bulk of thesoil.5.1.2 Abrasive CleaningOxide and other films may beremoved by mechanical techniques using such abrasives as fineemery on a cloth or a wheel, pumice slurry, or greaselessbuffing compounds. Grit blasting, shot blasting, wet blasting,1This practic
13、e is under the jurisdiction of ASTM Committee B08 on Metallicand Inorganic Coatings and is the direct responsibility of Subcommittee B08.02 onPre Treatment.Current edition approved Nov. 1, 2010. Published November 2010. Originallyapproved in 1977. Last previous edition approved in 2006 as B630 88 (2
14、006).DOI: 10.1520/B0630-88R10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International,
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB63019882010STANDARDPRACTICEFORPREPARATIONOFCHROMIUMFORELECTROPLATINGWITHCHROMIUM 电镀 制备 标准 实施 规程

链接地址:http://www.mydoc123.com/p-461807.html