ASTM B535-2006(2011) Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube《镍铁铬硅合金(UNS N08330和N08332)无缝管道和管用标准规范》.pdf

《ASTM B535-2006(2011) Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube《镍铁铬硅合金(UNS N08330和N08332)无缝管道和管用标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM B535-2006(2011) Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube《镍铁铬硅合金(UNS N08330和N08332)无缝管道和管用标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B535 06 (Reapproved 2011)Standard Specification forNickel-Iron-Chromium-Silicon Alloys (UNS N08330 andN08332) Seamless Pipe and Tube1This standard is issued under the fixed designation B535; the number immediately following the designation indicates the year oforiginal adoption or, in t

2、he case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification2covers alloys UNS N08330 andN08332 in the form of hot-finished an

3、d cold-finished seamlesspipe and tube intended for heat resisting applications andgeneral corrosive service.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are n

4、ot considered standard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (MSDS) for

5、this product/materialas provided by the manufacturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3B829 Specification for General Requirements for Nickeland Nickel Alloys Seamless

6、 Pipe and TubeB899 Terminology Relating to Non-ferrous Metals andAlloys3. Terminology3.1 Definitions:3.1.1 Definitions for terms defined in Terminology B899shall apply unless otherwise defined by the requirements of thisdocument.4. General Requirement4.1 Material furnished under this specification s

7、hall con-form to the applicable requirements of Specification B829unless otherwise provided herein.5. Ordering Information5.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for material ordered under thisspecification. Examples of such requirements include, b

8、ut arenot limited to, the following:5.1.1 Alloy name or UNS number,5.1.2 ASTM designation and year of issue,5.1.3 Dimensions:5.1.3.1 PipeSpecify standard pipe size and schedule,5.1.3.2 TubeSpecify outside diameter and nominal orminimum wall,5.1.3.3 Length (specific or random),5.1.4 Finish:5.1.4.1 Pi

9、peSpecify cold-worked or hot-worked,5.1.4.2 TubeSpecify cold-worked or hot-finished,5.1.5 Quantity (feet or meters or number of pieces),5.1.6 Hydrostatic Test or Nondestructive Electric TestSpecify type of test (see 8.4),5.1.7 CertificationState if certification is required,5.1.8 Samples for Product

10、 (Check) AnalysisState whethersamples for product analysis should be furnished, and5.1.9 Purchaser InspectionIf purchaser wishes to witnesstests or inspection of material at place of manufacture, thepurchase order must so state indicating which test or inspec-tions are to be witnessed.6. Materials a

11、nd Manufacture6.1 Heat TreatmentThe material shall be furnished in theannealed condition. The final heat treatment of UNS N08330shall be 1900F (1040C) minimum. The final heat treatmentof UNS N08332 shall be 2100F (1150C) minimum.7. Chemical Composition7.1 The material shall conform to the compositio

12、n limitsspecified in Table 1.7.1.1 A chemical analysis shall be made on each lot ofmaterial as described in Specification B829.1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel a

13、nd Cobalt and Their Alloys.Current edition approved June 1, 2011. Published June 2011. Originallyapproved in 1970. Last previous edition approved in 2006 as B535 06. DOI:10.1520/B0535-06R11.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SB-535 in Section II of that

14、 Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of th

15、is standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7.2 If a product (check) analysis is performed by thepurchaser, the material shall conform to the product analysisvariations prescribed in Specification B829.8. Mechanical an

16、d Other Properties8.1 The material shall conform to the mechanical propertieslisted in Table 2.8.1.1 One tension test shall be made on each lot of material.8.2 Grain SizeAnnealed alloy UNS N08332 shall con-form to an average grain size of ASTM No. 5 or coarser. Onetest per lot is required.8.3 Flatte

17、ning TestOne section of pipe or tube per lot, notless than 212 in. (63.5 mm) in length, shall be flattened coldbetween parallel plates in two steps. During the first step,which is test for ductility, no cracks or breaks on the inside,outside or end surfaces shall occur until the distance betweenthe

18、plates is less than the value H calculates as follows:H 5 1.09 t/0.09 1 t/D! (1)whereH = distance between parallel plates, in.,t = specified wall thickness, in., andD = nominal outside diameter, in.During the second step, which is a test for soundness, theflattening shall be continued until the spec

19、imen breaks or theopposite walls of the pipe or tube meet.8.4 Hydrostatic Test or Nondestructive Electric Test:8.4.1 Each pipe or tube shall be subjected to either thehydrostatic test or to a nondestructive electric test as perprescribed in Specification B829. The type of test to be usedshall be at

20、the option of the manufacturer, unless specified inthe purchase order.8.4.2 If any tube or pipe shows leak during hydrostatictesting, it shall be rejected.9. Dimensions and Permissible Variations9.1 The permissible variations in outside diameter for pipe,both cold-finished and hot-finished, are show

21、n in Table 3.Other dimensions and permissible variations are provided inSpecification B829.10. Keywords10.1 high-temperature alloy; seamless pipe; seamless tube;N08330; N08332TABLE 1 Chemical RequirementsElement Composition Limits, %C .AMn 2.00 maxP 0.03 maxS 0.03 maxSi 0.751.50Cr 17.020.0Ni 34.037.

22、0Cu 1.00 maxPb 0.005 maxSn 0.025 maxFe remainderBAAlloy UNS N08330: 0.08 max.Alloy UNS N08332: 0.05 to 0.10.BElement shall be determined arithmetically by difference.TABLE 2 Mechanical PropertiesAlloy ConditionTensile Strength,min, psi (MPa)Yield Strength, 0.2 % offset,min, psi (MPa)Elongation in 2

23、in. or 50mm, or 4D,min,%HardnessAUNS N08330 annealed 70 000 (483) 30 000 (207) 30 70 to 90 HRBUNS N08332 annealed 67 000 (462) 27 000 (186) 30 65 to 88 HRBAHardness values are informative only and not to be construed as the basis for acceptance.TABLE 3 Permissible Variations in Outside Diameter, Hot

24、-Finished and Cold-Finished PipeNominal Pipe Size, in.Permissible Variations in Outside DiameterOver Underin. mm in. mm18 to 112 , incl164 0.4132 0.8Over 112 to 4, incl132 0.8132 0.8Over 4 to 8, incl116 1.6132 0.8Over 8 to 18, incl332 2.4132 0.8B535 06 (2011)2SUMMARY OF CHANGESCommittee B02 has iden

25、tified the location of selected changes to this standard since the last issue (B535 - 04)that may impact the use of this standard. (Approved December 1, 2006.)(1) Clarifying of the nondestructive electric test in lieu ofhydrostatic test at the option of the manufacturer.(2) Revision of 5.1 and 8.4.A

26、STM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are

27、entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standard

28、sand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committe

29、e on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).B535 06 (2011)3