ASTM B535-2006 Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube《镍铁铬硅合金(UNS N08330和N08332)无缝管道和管用标准规范》.pdf
《ASTM B535-2006 Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube《镍铁铬硅合金(UNS N08330和N08332)无缝管道和管用标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM B535-2006 Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube《镍铁铬硅合金(UNS N08330和N08332)无缝管道和管用标准规范》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B 535 06Standard Specification forNickel-Iron-Chromium-Silicon Alloys (UNS N08330 andN08332) Seamless Pipe and Tube1This standard is issued under the fixed designation B 535; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revis
2、ion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification2covers alloys UNS N08330 andN08332 in the form of hot-finished and cold-finished
3、 seamlesspipe and tube intended for heat resisting applications andgeneral corrosive service.1.2 The values stated in inch-pound units are to be consid-ered as the standard. The values given in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concern
4、s, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and heal
5、th practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3B 829 Specification for General Requirements for Nickeland Nickel Alloys Seamless Pipe and TubeB 899 Terminology Relating to Non-ferrous Metals andAlloys3. Terminology3.1 De
6、finitions:3.1.1 Definitions for terms defined in Terminology B 899shall apply unless otherwise defined by the requirements of thisdocument.4. General Requirement4.1 Material furnished under this specification shall con-form to the applicable requirements of Specification B 829unless otherwise provid
7、ed herein.5. Ordering Information5.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for material ordered under thisspecification. Examples of such requirements include, but arenot limited to, the following:5.1.1 Alloy name or UNS number,5.1.2 ASTM designation
8、 and year of issue,5.1.3 Dimensions:5.1.3.1 PipeSpecify standard pipe size and schedule,5.1.3.2 TubeSpecify outside diameter and nominal orminimum wall,5.1.3.3 Length (specific or random),5.1.4 Finish:5.1.4.1 PipeSpecify cold-worked or hot-worked,5.1.4.2 TubeSpecify cold-worked or hot-finished,5.1.5
9、 Quantity (feet or meters or number of pieces),5.1.6 Hydrostatic Test or Nondestructive Electric TestSpecify type of test (see 8.4),5.1.7 CertificationState if certification is required,5.1.8 Samples for Product (Check) AnalysisState whethersamples for product analysis should be furnished, and5.1.9
10、Purchaser InspectionIf purchaser wishes to witnesstests or inspection of material at place of manufacture, thepurchase order must so state indicating which test or inspec-tions are to be witnessed.6. Materials and Manufacture6.1 Heat TreatmentThe material shall be furnished in theannealed condition.
11、 The final heat treatment of UNS N08330shall be 1900F (1040C) minimum. The final heat treatmentof UNS N08332 shall be 2100F (1150C) minimum.7. Chemical Composition7.1 The material shall conform to the composition limitsspecified in Table 1.1This specification is under the jurisdiction of ASTM Commit
12、tee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and Their Alloys.Current edition approved Dec. 1, 2006. Published January 2007. Originallyapproved in 1970. Last previous edition approved in 2004 as B 535 04.2For ASME Boiler a
13、nd Pressure Vessel Code applications see related Specifi-cation SB-535 in Section II of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Docu
14、ment Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7.1.1 A chemical analysis shall be made on each lot ofmaterial as described in Spe
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB5352006STANDARDSPECIFICATIONFORNICKELIRONCHROMIUMSILICONALLOYSUNSN08330ANDN08332SEAMLESSPIPEANDTUBE

链接地址:http://www.mydoc123.com/p-461492.html